Pull power supply and reset updates from Sebastian Reichel:

 - Add new Qualcomm PMI8998/PM660 SMB2 charger

 - bq256xx: support systems without thermistors

 - cros_pchg: fix peripheral device status after system resume

 - axp20x_usb_power: add support for AXP192

 - qcom-pon: add support for pm8941

 - at91-reset: prepare to expose reset reason to sysfs

 - switch all I2C drivers back to use .probe instead of .probe_new

 - convert some more DT bindings to YAML

 - misc cleanups

* tag 'for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
  MAINTAINERS: add documentation file for Microchip SAMA5D2 shutdown controller
  dt-bindings: power: reset: atmel,sama5d2-shdwc: convert to yaml
  dt-bindings: power: reset: atmel,at91sam9260-shdwc: convert to yaml
  power: reset: at91-reset: change the power on reason prototype
  power: reset: qcom-pon: add support for pm8941-pon
  dt-bindings: power: reset: qcom-pon: define pm8941-pon
  power: supply: add Qualcomm PMI8998 SMB2 Charger driver
  dt-bindings: power: supply: qcom,pmi8998-charger: add bindings for smb2 driver
  power: supply: rt9467: Make charger-enable control as logic level
  power: supply: Switch i2c drivers back to use .probe()
  power: reset: add HAS_IOPORT dependencies
  dt-bindings: power: supply: axp20x: Add AXP192 compatible
  power: supply: axp20x_usb_power: Add support for AXP192
  power: supply: axp20x_usb_power: Remove variant IDs from VBUS polling check
  power: supply: axp20x_usb_power: Use regmap field for VBUS disabling
  power: supply: axp20x_usb_power: Use regmap fields for USB BC feature
  power: supply: axp20x_usb_power: Use regmap fields for VBUS monitor feature
  power: supply: axp20x_usb_power: Simplify USB current limit handling
  power: supply: hwmon: constify pointers to hwmon_channel_info
  power: supply: twl4030_madc_battery: Refactor twl4030_madc_bat_ext_changed()
  ...

Pull LED updates from Lee Jones:
 "New Drivers:
   - Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
   - Add support for Awinic AW20036/AW20054/AW20072 LEDs

  New Device Support:
   - Add support for PMI632 LPG to QCom LPG
   - Add support for PMI8998 to QCom Flash
   - Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC

  New Functionality:
   - Implement the LP55xx Charge Pump
   - Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
   - Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
   - Enable per-pin resolution Pinctrl in LEDs GPIO

  Fix-ups:
   - Allow thread to sleep by switching from spinlock to mutex
   - Add lots of Device Tree bindings / support
   - Adapt relationships / dependencies driven by Kconfig
   - Switch I2C drivers from .probe_new() to .probe()
   - Remove superfluous / duplicate code
   - Replace strlcpy() with strscpy() for efficiency and overflow prevention
   - Staticify various functions
   - Trivial: Fixing coding style
   - Simplify / reduce code

  Bug Fixes:
   - Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
   - Repair race between led_set_brightness(LED_{OFF,FULL})
   - Fix Oops relating to sleeping in critical sections
   - Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
   - Do not leak resources in error handling paths
   - Fix unsigned comparison which can never be negative
   - Provide missing NULL terminating entries in tables
   - Fix misnaming issues"

* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
  leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
  leds: sgm3140: Add richtek,rt5033-led compatible
  dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
  dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
  dt-bindings: leds: Drop unneeded quotes
  leds: Fix config reference for AW200xx driver
  leds: leds-mt6323: Add support for WLEDs and MT6332
  leds: leds-mt6323: Add support for MT6331 leds
  leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
  leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
  leds: leds-mt6323: Specify registers and specs in platform data
  dt-bindings: leds: leds-mt6323: Document mt6332 compatible
  dt-bindings: leds: leds-mt6323: Document mt6331 compatible
  leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
  leds: simatic-ipc-leds-gpio: Split up into multiple drivers
  leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
  leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
  leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
  leds: cht-wcove: Remove unneeded semicolon
  leds: cht-wcove: Fix an unsigned comparison which can never be negative
  ...

Pull MFD updates from Lee Jones:
 "New Drivers:
   - Add support for TI TPS6594/TPS6593/LP8764 PMICs
   - Add support for Samsung RT5033 Battery Charger
   - Add support for Analog Devices MAX77540 and MAX77541 PMICs

  New Device Support:
   - Add support for SPI to Rockchip RK808 (and friends)
   - Add support for AXP192 PMIC to X-Powers AXP20X
   - Add support for AXP313a PMIC to X-Powers AXP20X
   - Add support for RK806 to Rockchip RK8XX

  Removed Device Support:
   - Removed MFD support for Richtek RT5033 Battery

  Fix-ups:
   - Remove superfluous code
   - Switch I2C drivers from .probe_new() to .probe()
   - Convert over to managed resources (devm_*(), etc)
   - Use dev_err_probe() for returning errors from .probe()
   - Add lots of Device Tree bindings / support
   - Improve cache efficiency by switching to Maple
   - Use own exported namespaces (NS)
   - Include missing and remove superfluous headers
   - Start using / convert to the new shutdown sys-off API
   - Trivial: variable / define renaming
   - Make use of of_property_read_reg() when requesting DT 'reg's

  Bug Fixes:
   - Fix chip revision readout due to incorrect data masking
   - Amend incorrect register and mask values used for charger state
   - Hide unused functionality at compile time
   - Fix resource leaks following error handling routines
   - Return correct error values and fix error handling in general
   - Repair incorrect device names - used for device matching
   - Remedy broken module auto-loading"

* tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (51 commits)
  dt-bindings: mfd: max77541: Add ADI MAX77541/MAX77540
  iio: adc: max77541: Add ADI MAX77541 ADC Support
  regulator: max77541: Add ADI MAX77541/MAX77540 Regulator Support
  dt-bindings: regulator: max77541: Add ADI MAX77541/MAX77540 Regulator
  mfd: Switch two more drivers back to use struct i2c_driver::probe
  dt-bindings: mfd: samsung,s5m8767: Simplify excluding properties
  mfd: stmpe: Only disable the regulators if they are enabled
  mfd: max77541: Add ADI MAX77541/MAX77540 PMIC Support
  dt-bindings: mfd: gateworks-gsc: Remove unnecessary fan-controller nodes
  mfd: core: Use of_property_read_reg() to parse "reg"
  mfd: stmfx: Nullify stmfx->vdd in case of error
  mfd: stmfx: Fix error path in stmfx_chip_init
  mfd: intel-lpss: Add missing check for platform_get_resource
  mfd: stpmic1: Add PMIC poweroff via sys-off handler
  mfd: stpmic1: Fixup main control register and bits naming
  dt-bindings: mfd: qcom,tcsr: Add the compatible for IPQ8074
  mfd: tps65219: Add support for soft shutdown via sys-off API
  mfd: pm8008: Drop bogus i2c module alias
  mfd: pm8008: Fix module autoloading
  mfd: tps65219: Add GPIO cell instance
  ...

It is quite uncommon to use a driver helper with parameters like *pdev
and __iomem *base. It is much cleaner and close to today's standards to
provide the per-device driver structure and then access its
internals. Let's do this with the helper which returns the power on
reason. While we change the parameters, we can as well rename the
function from at91_reset_status() to at91_reset_reason() to be more
accurate with what the helper actually does, and finally because we don't
really need the pdev argument in this helper besides for printing the
reset reason, we can move the dev_info() call into the probe.

All these modifications prepare the introduction of a sysfs entry to
access this information. This way the diff will be much smaller. Thus,
there is no intended functional change.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

For PM8941 we don't have a defined field to store the reset reason.
Support wrapping pwrkey and resin, but without writing the reset
reason.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add a driver for the SMB2 charger block found in the Qualcomm PMI8998
and PM660.

This driver is capable of utilising Qualcomm's Automatic Power Source
Detection (APSD) BC1.2 implementation, as well as Automatic Input
Current Limiting (AICL) to configure the maximum input current
limit of DCP (wall) chargers.

Quick Charge is not currently supported.

Most devices using the smb2 charger have a secondary dedicated charger
chip which is used in parallel to enable faster charger without
overheating. However, not all do, as a result to ensure safety until
these are supported, the maximum current is limited to ~1A via the
FAST_CHARGE_CURRENT_CFG register.

Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The rt5033-battery fuelgauge can't get a status by itself. The rt5033-charger
can, let's get this value.

To get the charger as a "supplier" from the devicetree, the "of_node" needs
to be initiated.

Additionally, in the probe function replace dev_err() with dev_err_probe(),
this will avoid printing an error for -EPROBE_DEFER when the battery driver
probes before the charger driver.

Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/a2015d257b145108a3ecdf107a3040362c887fc5.1684182964.git.jahau@rocketmail.com

Move struct rt5033_battery from the mfd header into the battery driver because
it's not used by others.

Within struct rt5033_battery, remove the line "struct rt5033_dev *rt5033;"
because it doesn't get used.

In rt5033.h, remove #include <linux/power_supply.h>, it's not necessary
anymore.

In rt5033_battery.c, remove #include <linux/mfd/rt5033.h>, it's not necessary
anymore either. Instead add #include <linux/regmap.h> and

Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/736e1cbee257853cb3d1da6f05c184e9a053263b.1684182964.git.jahau@rocketmail.com

This patch adds device driver of Richtek RT5033 PMIC. The driver supports
switching charger. rt5033 charger provides three charging modes. The charging
modes are pre-charge mode, fast charge mode and constant voltage mode. They
vary in charge rate, the charge parameters can be controlled by i2c interface.

Tested-by: Raymond Hackley <raymondhackley@protonmail.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/9556d4ebb30fd321e37aa0eb343554122e4720c9.1684182964.git.jahau@rocketmail.com