[ Upstream commit 3a3acf839b2cedf092bdd1ff65b0e9895df1656b ]

Commit 223a3b82834f ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.

Fix this by applying the same conditional to determine which register
should be read.

This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.

This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).

Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 61978807b00f8a1817b0e5580981af1cd2f428a5 ]

The POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN and
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN values should be immutable
properties of the battery, but for this driver they are writable values
and used as the minimum and maximum values for charging. Remove the
DESIGN designation from these values.

Fixes: 46c202b5f25f ("power: supply: add battery driver for AXP20X and AXP22X PMICs")
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-3-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Pull power sequencing fix from Bartosz Golaszewski:
 "A follow-up fix for the power sequencing subsystem. It turned out the
  previous fix for this driver was incomplete and broke the WLAN support
  on some platforms. This addresses the issue.

   - set the direction of the wlan-enable GPIO to output after
     requesting it as-is"

* tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  power: sequencing: qcom-wcn: set the wlan-enable GPIO to output

Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.

Fixes: a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is")
Link: https://lore.kernel.org/r/20240823115500.37280-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Pull ARM SoC fixes from Arnd Bergmann:
 "There is a fairly large number of bug fixes for Qualcomm platforms,
  most of them addressing issues with the devicetree files for the newly
  added Snapdragon X1 based laptops to make them more reliable.

  The Qualcomm driver changes address a few build-time issues as well as
  runtime problems in the tzmem and scm firmware, the USB Type-C driver,
  and the cmd-db and pmic_glink soc drivers.

  The NXP i.MX usually gets a bunch of devicetree fixes that is
  proportional to the number of supported machines. This includes both
  warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
  layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
  board.

  The other changes are the usual minor changes, including an update to
  the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
  (risc-v)"

* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
  firmware: microchip: fix incorrect error report of programming:timeout on success
  soc: qcom: pd-mapper: Fix singleton refcount
  firmware: qcom: tzmem: disable sdm670 platform
  soc: qcom: pmic_glink: Actually communicate when remote goes down
  usb: typec: ucsi: Move unregister out of atomic section
  soc: qcom: pmic_glink: Fix race during initialization
  firmware: qcom: qseecom: remove unused functions
  firmware: qcom: tzmem: fix virtual-to-physical address conversion
  firmware: qcom: scm: Mark get_wq_ctx() as atomic call
  arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
  arm64: dts: qcom: disable GPU on x1e80100 by default
  arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
  arm64: dts: imx95: correct L3Cache cache-sets
  arm64: dts: imx95: correct a55 power-domains
  arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
  arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
  ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
  arm64: dts: imx93: update default value for snps,clk-csr
  arm64: dts: freescale: tqma9352: Fix watchdog reset
  arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
  ...

Qualcomm driver fixes for v6.11

This corrects the tzmem virt-to-phys conversion, which caused issues for
the uefisecapp implementation of EFI variable access. SDM670 is excluded
from tzmem usage due to reported issues.

The SCM get wait queue context call is corrected to be marked ATOMIC and
some dead code in qseecom, following the tzmem conversion, is removed.

The memory backing command DB is remapped writecombined, to avoid XPU
violations when Linux runs without the Qualcomm hypervisor.

Two compile fixes are added for pd-mapper, and the broken reference
count is corrected, to make pd-mapper deal with remoteprocs going away.

In pmic_glink a race condition where the client callbacks might be
called before we returned the client handle is corrected. The broken conditions
for when to signal that the firmware is going down is also corrected.

In the pmic_glink UCSI driver, the ucsi_unregister() is moved out of the
pdr callback, as this is being invoked in atomic context.

Konrad's email address is updated in MAINTAINERS, and related mailmap
entries are added.

* tag 'qcom-drivers-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  soc: qcom: pd-mapper: Fix singleton refcount
  firmware: qcom: tzmem: disable sdm670 platform
  soc: qcom: pmic_glink: Actually communicate when remote goes down
  usb: typec: ucsi: Move unregister out of atomic section
  soc: qcom: pmic_glink: Fix race during initialization
  firmware: qcom: qseecom: remove unused functions
  firmware: qcom: tzmem: fix virtual-to-physical address conversion
  firmware: qcom: scm: Mark get_wq_ctx() as atomic call
  MAINTAINERS: Update Konrad Dybcio's email address
  mailmap: Add an entry for Konrad Dybcio
  soc: qcom: pd-mapper: mark qcom_pdm_domains as __maybe_unused
  soc: qcom: cmd-db: Map shared memory as WC, not WB
  soc: qcom: pd-mapper: Depend on ARCH_QCOM || COMPILE_TEST

Link: https://lore.kernel.org/r/20240826145209.1646159-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull power sequencing fix from Bartosz Golaszewski:

 - request the wlan-enable GPIO "as-is" to fix an issue with the wifi
   module being already powered up before linux boots

* tag 'pwrseq-fixes-for-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  power: sequencing: request the WLAN enable GPIO as-is

As pointed out by Stephen Boyd it is possible that during initialization
of the pmic_glink child drivers, the protection-domain notifiers fires,
and the associated work is scheduled, before the client registration
returns and as a result the local "client" pointer has been initialized.

The outcome of this is a NULL pointer dereference as the "client"
pointer is blindly dereferenced.

Timeline provided by Stephen:
 CPU0                               CPU1
 ----                               ----
 ucsi->client = NULL;
 devm_pmic_glink_register_client()
  client->pdr_notify(client->priv, pg->client_state)
   pmic_glink_ucsi_pdr_notify()
    schedule_work(&ucsi->register_work)
    <schedule away>
                                    pmic_glink_ucsi_register()
                                     ucsi_register()
                                      pmic_glink_ucsi_read_version()
                                       pmic_glink_ucsi_read()
                                        pmic_glink_ucsi_read()
                                         pmic_glink_send(ucsi->client)
                                         <client is NULL BAD>
 ucsi->client = client // Too late!

This code is identical across the altmode, battery manager and usci
child drivers.

Resolve this by splitting the allocation of the "client" object and the
registration thereof into two operations.

This only happens if the protection domain registry is populated at the
time of registration, which by the introduction of commit '1ebcde047c54
("soc: qcom: add pd-mapper implementation")' became much more likely.

Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/all/CAMi1Hd2_a7TjA7J9ShrAbNOd_CoZ3D87twmO5t+nZxC9sX18tA@mail.gmail.com/
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/ZqiyLvP0gkBnuekL@hovoldconsulting.com/
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://lore.kernel.org/all/CAE-0n52JgfCBWiFQyQWPji8cq_rCsviBpW-m72YitgNfdaEhQg@mail.gmail.com/
Fixes: 58ef4ece1e41 ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-1-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

If the WCN module is powered up before linux boots and the ath11k driver
probes at the same time as the power sequencing driver, we may end up
driving the wlan-enable GPIO low in the latter, breaking the start-up of
the WLAN module. Request the wlan-enable GPIO as-is so that if the WLAN
module is already starting/started, we leave it alone.

Fixes: 2f1630f437df ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Reported-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20240813190751.155035-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Pull power supply fixes from Sebastian Reichel:
 "rt5033:
   - fix driver regression causing kernel oops

  axp288-charger:
   - fix charge voltage setup

  qcom-battmgr:
   - fix thermal zone spamming errors
   - fix init on Qualcomm X Elite"

* tag 'for-v6.11-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: qcom_battmgr: Ignore extra __le32 in info payload
  power: supply: qcom_battmgr: return EAGAIN when firmware service is not up
  power: supply: axp288_charger: Round constant_charge_voltage writes down
  power: supply: axp288_charger: Fix constant_charge_voltage writes
  power: supply: rt5033: Bring back i2c_set_clientdata