commit 5bc28b93a36e3cb3acc2870fb75cb6ffb182fece upstream.

Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:

[    1.452598] power_supply_read_temp+0x78/0x80
[    1.458680] thermal_zone_get_temp+0x5c/0x11c
[    1.464765] thermal_zone_device_update+0x34/0xb4
[    1.471195] thermal_zone_device_register+0x87c/0x8cc
[    1.477974] __power_supply_register+0x364/0x424
[    1.484317] power_supply_register_no_ws+0x10/0x18
[    1.490833] bq27xxx_battery_setup+0x10c/0x164
[    1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[    1.503435] i2c_device_probe+0x174/0x240
[    1.509172] driver_probe_device+0x1fc/0x29c
[    1.515167] __driver_attach+0xa4/0xa8
[    1.520643] bus_for_each_dev+0x58/0x98
[    1.526204] driver_attach+0x20/0x28
[    1.531505] bus_add_driver+0x1c8/0x22c
[    1.537067] driver_register+0x68/0x108
[    1.542630] i2c_register_driver+0x38/0x7c
[    1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[    1.555321] do_one_initcall+0x38/0x12c
[    1.560886] kernel_init_freeable+0x148/0x1ec
[    1.566972] kernel_init+0x10/0xfc
[    1.572101] ret_from_fork+0x10/0x40

Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.

Fixes: 297d716f6260 ("power_supply: Change ownership from driver to core")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MFD updates from Lee Jones:
 "New Device Support:
   - Add support for 88pm860; 88pm80x
   - Add support for 24c08 EEPROM; at24
   - Add support for Broxton Whiskey Cove; intel*
   - Add support for RTS522A; rts5227
   - Add support for I2C devices; intel_quark_i2c_gpio

  New Functionality:
   - Add microphone support; arizona
   - Add general purpose switch support; arizona
   - Add fuel-gauge support; da9150-core
   - Add shutdown support; sec-core
   - Add charger support; tps65217
   - Add flexible serial communication unit support; atmel-flexcom
   - Add power button support; axp20x
   - Add led-flash support; rt5033

  Core Frameworks:
   - Supply a generic macro for defining Regmap IRQs
   - Rework ACPI child device matching

  Fix-ups:
   - Use Regmap to access registers; tps6105x
   - Use DEFINE_RES_IRQ_NAMED() macro; da9150
   - Re-arrange device registration order; intel_quark_i2c_gpio
   - Allow OF matching; cros_ec_i2c, atmel-hlcdc, hi6421-pmic, max8997, sm501
   - Handle deferred probe; twl6040
   - Improve accuracy of headphone detect; arizona
   - Unnecessary MODULE_ALIAS() removal; bcm590xx, rt5033
   - Remove unused code; htc-i2cpld, arizona, pcf50633-irq, sec-core
   - Simplify code; kempld, rts5209, da903x, lm3533, da9052, arizona
   - Remove #iffery; arizona
   - DT binding adaptions; many

  Bug Fixes:
   - Fix possible NULL pointer dereference; wm831x, tps6105x
   - Fix 64bit bug; intel_soc_pmic_bxtwc
   - Fix signedness issue; arizona"

* tag 'mfd-for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (73 commits)
  bindings: mfd: s2mps11: Add documentation for s2mps15 PMIC
  mfd: sec-core: Remove unused s2mpu02-rtc and s2mpu02-clk children
  extcon: arizona: Add extcon specific device tree binding document
  MAINTAINERS: Add binding docs for Cirrus Logic/Wolfson Arizona devices
  mfd: arizona: Remove bindings covered in new subsystem specific docs
  mfd: rt5033: Add RT5033 Flash led sub device
  mfd: lpss: Add Intel Broxton PCI IDs
  mfd: lpss: Add Broxton ACPI IDs
  mfd: arizona: Signedness bug in arizona_runtime_suspend()
  mfd: axp20x: Add a cell for the power button part of the, axp288 PMICs
  mfd: dt-bindings: Document pulled down WRSTBI pin on S2MPS1X
  mfd: sec-core: Disable buck voltage reset on watchdog falling edge
  mfd: sec-core: Dump PMIC revision to find out the HW
  mfd: arizona: Use correct type ID for device tree config
  mfd: arizona: Remove use of codec build config #ifdefs
  mfd: arizona: Simplify adding subdevices
  mfd: arizona: Downgrade type mismatch messages to dev_warn
  mfd: arizona: Factor out checking of jack detection state
  mfd: arizona: Factor out DCVDD isolation control
  mfd: Make TPS6105X select REGMAP_I2C
  ...

Pull power supply and reset updates from Sebastian Reichel:
 - new AXP20X USB Power driver
 - new Qualcomm SMBB driver
 - new TPS65217 Charger driver
 - BQ24257: add BQ24250/BQ24251 support
 - overhaul bq27x00 battery driver, rename to bq27xxx
 - misc fixes and cleanups

* tag 'for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
  power: bq27xxx_battery: Remove unneeded dependency in Kconfig
  power: bq27xxx_battery: move irq handler to i2c section
  power: bq27xxx_battery: fix platform probe
  twl4030_charger: add missing iio dependency
  power_supply: charger-manager: add missing of_node_put
  Documentation: power: bq24257: Document exported sysfs entries
  power: bq24257: Add various device-specific sysfs properties
  power: bq24257: Allow input current limit sysfs access
  power: bq24257: Add input DPM voltage threshold setting support
  power: bq24257: Add over voltage protection setting support
  power: bq24257: Add SW-based approach for Power Good determination
  power: bq24257: Allow manual setting of input current limit
  power: bq24257: Add bit definition for temp sense enable
  power: bq24257: Add basic support for bq24250/bq24251
  dt: power: bq24257-charger: Cover additional devices
  power: bq24257: Simplify bq24257_power_supply_init()
  power: bq24257: Use managed power supply register
  power: bq24257: Streamline input current limit setup
  power: bq24257: Remove IRQ config through stat-gpios
  power: bq27xxx_battery: fix signedness bug in bq27xxx_battery_read_health()
  ...

I2C is only required when using the config item BATTERY_BQ27XXX_I2C which
already depends on the I2C subsystem, remove the unneeded dependency from
BATTERY_BQ27XXX.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The IRQ handler is not used by the platform based
code resulting in a 'defined but not used' warning,
if CONFIG_BQ27XXX_I2C is not enabled.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>

Add missing initialization of register mapping table to
platform probe function.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>

This driver fails to link without CONFIG_IIO, since
there are no stubs for the iio_channels functions.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Marek Belisko <marek@goldelico.com>
Acked-by: Nikolaus Schaller <hns@goldelico.com>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This adds power supply driver support for the Fuel-Gauge part of
the DA9150 combined Charger and Fuel-Gauge device.

Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>