linux-stable.git/drivers/power, branch v3.16.45 Linux kernel stable tree power: supply: bq24190_charger: Handle fault before status on interrupt 2017-06-05T20:16:56+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:54+00:00 15367f1059f9e2831e56cb5a01fd6beaed334fb1 commit ba52e75718784fda1b683ee0bfded72a0b83b047 upstream. Reading both fault and status registers and logging any fault should take priority over handling status register update. Fix by moving the status handling to later in interrupt routine. Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit ba52e75718784fda1b683ee0bfded72a0b83b047 upstream.

Reading both fault and status registers and logging any fault should
take priority over handling status register update.

Fix by moving the status handling to later in interrupt routine.

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: bq24190_charger: Don't read fault register outside irq_handle_thread() 2017-06-05T20:16:56+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:53+00:00 57ab80e6f5a605910c402a416822c33f82eeb986 commit 68abfb8015832ddf728b911769659468efaf8bd9 upstream. Caching the fault register after a single I2C read may not keep an accurate value. Fix by doing two reads in irq_handle_thread() and using the cached value elsewhere. If a safety timer fault later clears itself, we apparently don't get an interrupt (INT), however other interrupts would refresh the register cache. From the data sheet: "When a fault occurs, the charger device sends out INT and keeps the fault state in REG09 until the host reads the fault register. Before the host reads REG09 and all the faults are cleared, the charger device would not send any INT upon new faults. In order to read the current fault status, the host has to read REG09 two times consecutively. The 1st reads fault register status from the last read [1] and the 2nd reads the current fault register status." [1] presumably a typo; should be "last fault" Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 68abfb8015832ddf728b911769659468efaf8bd9 upstream.

Caching the fault register after a single I2C read may not keep an accurate
value.

Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.

From the data sheet: "When a fault occurs, the charger device sends out INT
 and keeps the fault state in REG09 until the host reads the fault register.
 Before the host reads REG09 and all the faults are cleared, the charger
 device would not send any INT upon new faults. In order to read the
 current fault status, the host has to read REG09 two times consecutively.
 The 1st reads fault register status from the last read [1] and the 2nd reads
 the current fault register status."

[1] presumably a typo; should be "last fault"

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: bq24190_charger: Call power_supply_changed() for relevant component 2017-06-05T20:16:56+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:52+00:00 167dc75c2faf2a8b237d44de1d1770e59602c382 commit 2d9fee6a42ea170e4378b3363a7ad385d0e67281 upstream. We wrongly get uevents for bq24190-charger and bq24190-battery on every register change. Fix by checking the association with charger and battery before emitting uevent(s). Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2d9fee6a42ea170e4378b3363a7ad385d0e67281 upstream.

We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.

Fix by checking the association with charger and battery before
emitting uevent(s).

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: bq24190_charger: Change first_time flag reset condition 2017-06-05T20:16:56+00:00 Thomas Elste thomas.elste@imms.de 2015-05-28T09:05:32+00:00 d3b941b0085e560e1c522d920646833bf96d6606 commit cd054ee16580690830297dbda0abe9c184276d6a upstream. The initial register reset of BQ24190 generates a charger status change whose propagation via power_supply_changed is prevented using a flag. This flag gets never reset so all following events are ignored as well leading for example to userspace not detecting charger connects/disconnects. Therefor change the reset condition of first_time flag, so only the propagation of the first charger status change is prevented. Signed-off-by: Thomas Elste <thomas.elste@imms.de> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit cd054ee16580690830297dbda0abe9c184276d6a upstream.

The initial register reset of BQ24190 generates a charger status change
whose propagation via power_supply_changed is prevented using a flag.
This flag gets never reset so all following events are ignored as well
leading for example to userspace not detecting charger connects/disconnects.

Therefor change the reset condition of first_time flag, so only the
propagation of the first charger status change is prevented.

Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: bq24190_charger: Install irq_handler_thread() at end of probe() 2017-06-05T20:16:56+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:50+00:00 ebe8733e605cfbac3efa7c68e9fa3c13190ca628 commit d62acc5ef0621463446091ebd7a345e06e9ab80c upstream. The device specific data is not fully initialized on request_threaded_irq(). This may cause a crash when the IRQ handler tries to reference them. Fix the issue by installing IRQ handler at the end of the probe. Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d62acc5ef0621463446091ebd7a345e06e9ab80c upstream.

The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.

Fix the issue by installing IRQ handler at the end of the probe.

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: bq24190_charger: Call set_mode_host() on pm_resume() 2017-06-05T20:16:55+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:49+00:00 cddddea5a5ddae7cd61b54de55f91b3668c10eca commit e05ad7e0741ce0505e1df157c62b22b95172bb97 upstream. pm_resume() does a register_reset() which clears charger host mode. Fix by calling set_mode_host() after the reset. Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit e05ad7e0741ce0505e1df157c62b22b95172bb97 upstream.

pm_resume() does a register_reset() which clears charger host mode.

Fix by calling set_mode_host() after the reset.

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: bq24190_charger: Fix irq trigger to IRQF_TRIGGER_FALLING 2017-06-05T20:16:55+00:00 Liam Breck liam@networkimprov.net 2017-01-18T17:26:48+00:00 42a0e17be3a9c976c085b23271fa1bc7b37439ba commit 767eee362fd72bb2ca44cc80419ca4b38c6d8369 upstream. The interrupt signal is TRIGGER_FALLING. This is is specified in the data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us pulse to host to report charger device status and fault." Also the direction can be seen in the data sheet Figure 37 "BQ24190 with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k pull-up resistor installed for the sample configurations. Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 767eee362fd72bb2ca44cc80419ca4b38c6d8369 upstream.

The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."

Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.

Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: supply: max17042_battery: fix model download bug. 2016-11-20T01:17:10+00:00 Sven Van Asbroeck thesven73@gmail.com 2016-08-12T13:10:27+00:00 60a1618a6e8980b4e30916c4e645aa79b98caa39 commit 5381cfb6f0422da24cfa9da35b0433c0415830e0 upstream. The device's model download function returns the model data as an array of u32s, which is later compared to the reference model data. However, since the latter is an array of u16s, the comparison does not happen correctly, and model verification fails. This in turn breaks the POR initialization sequence. Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 5381cfb6f0422da24cfa9da35b0433c0415830e0 upstream.

The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.

Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
power: test_power: correctly handle empty writes 2016-02-02T19:47:55+00:00 Sasha Levin sasha.levin@oracle.com 2015-12-22T17:43:36+00:00 9b633ad428a989c35a83ecf78dc83353ef15f955 commit 6b9140f39c2aaf76791197fbab0839c0e4af56e8 upstream. Writing 0 length data into test_power makes it access an invalid array location and kill the system. Fixes: f17ef9b2d ("power: Make test_power driver more dynamic.") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com> 
commit 6b9140f39c2aaf76791197fbab0839c0e4af56e8 upstream.

Writing 0 length data into test_power makes it access an invalid array
location and kill the system.

Fixes: f17ef9b2d ("power: Make test_power driver more dynamic.")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
wm831x_power: Use IRQF_ONESHOT to request threaded IRQs 2015-12-13T17:49:27+00:00 Valentin Rothberg valentinrothberg@gmail.com 2015-09-22T17:00:40+00:00 95f16380b760ae890a0a89be95d30b1e39f76f62 commit 90adf98d9530054b8e665ba5a928de4307231d84 upstream. Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue. Fixes: b5874f33bbaf ("wm831x_power: Use genirq") Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com> 
commit 90adf98d9530054b8e665ba5a928de4307231d84 upstream.

Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.

scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.

Fixes: b5874f33bbaf ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>