[ Upstream commit e9945b2633deccda74a769d94060df49c53ff181 ]

The interrupt controller can detect only link changes. So in case an
external device generated a level based interrupt, then the interrupt
controller detected correctly the first edge. But the problem was that
the interrupt controller was detecting also the edge when the interrupt
was cleared. So it would generate another interrupt.
The fix for this is to clear the second interrupt but still check the
interrupt line status.

Fixes: c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20221018070959.1322606-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d21f4b7ffc22c009da925046b69b15af08de9d75 ]

Back in the description of commit e440e30e26dd ("arm64: dts: qcom:
sc7180: Avoid glitching SPI CS at bootup on trogdor") we described a
problem that we were seeing on trogdor devices. I'll re-summarize here
but you can also re-read the original commit.

On trogdor devices, the BIOS is setting up the SPI chip select as:
- mux special function (SPI chip select)
- output enable
- output low (unused because we've muxed as special function)

In the kernel, however, we've moved away from using the chip select
line as special function. Since the kernel wants to fully control the
chip select it's far more efficient to treat the line as a GPIO rather
than sending packet-like commands to the GENI firmware every time we
want the line to toggle.

When we transition from how the BIOS had the pin configured to how the
kernel has the pin configured we end up glitching the line. That's
because we _first_ change the mux of the line and then later set its
output. This glitch is bad and can confuse the device on the other end
of the line.

The old commit e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid
glitching SPI CS at bootup on trogdor") fixed the glitch, though the
solution was far from elegant. It essentially did the thing that
everyone always hates: encoding a sequential program in device tree,
even if it's a simple one. It also, unfortunately, got broken by
commit b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf
separately"). After that commit we did all the muxing _first_ even
though the config (set the pin to output high) was listed first. :(

I looked at ideas for how to solve this more properly. My first
thought was to use the "init" pinctrl state. In theory the "init"
pinctrl state is supposed to be exactly for achieving glitch-free
transitions. My dream would have been for the "init" pinctrl to do
nothing at all. That would let us delay the automatic pin muxing until
the driver could set things up and call pinctrl_init_done(). In other
words, my dream was:

  /* Request the GPIO; init it 1 (because DT says GPIO_ACTIVE_LOW) */
  devm_gpiod_get_index(dev, "cs", GPIOD_OUT_LOW);
  /* Output should be right, so we can remux, yay! */
  pinctrl_init_done(dev);

Unfortunately, it didn't work out. The primary reason is that the MSM
GPIO driver implements gpio_request_enable(). As documented in
pinmux.h, that function automatically remuxes a line as a GPIO. ...and
it does this remuxing _before_ specifying the output of the pin. You
can see in gpiod_get_index() that we call gpiod_request() before
gpiod_configure_flags(). gpiod_request() isn't passed any flags so it
has no idea what the eventual output will be.

We could have debates about whether or not the automatic remuxing to
GPIO for the MSM pinctrl was a good idea or not, but at this point I
think there is a plethora of code that's relying on it and I certainly
wouldn't suggest changing it.

Alternatively, we could try to come up with a way to pass the initial
output state to gpio_request_enable() and plumb all that through. That
seems like it would be doable, but we'd have to plumb it through
several layers in the stack.

This patch implements yet another alternative. Here, we specifically
avoid glitching the first time a pin is muxed to GPIO function if the
direction of the pin is output. The idea is that we can read the state
of the pin before we set the mux and make sure that the re-mux won't
change the state.

NOTES:
- We only do this the first time since later swaps between mux states
  might want to preserve the old output value. In other words, I
  wouldn't want to break a driver that did:
     gpiod_set_value(g, 1);
     pinctrl_select_state(pinctrl, special_state);
     pinctrl_select_default_state();
     /* We should be driving 1 even if "special_state" made the pin 0 */
- It's safe to do this the first time since the driver _couldn't_ have
  explicitly set a state. In order to even be able to control the GPIO
  (at least using gpiod) we have to have requested it which would have
  counted as the first mux.
- In theory, instead of keeping track of the first time a pin was set
  as a GPIO we could enable the glitch-free behavior only when
  msm_pinmux_request_gpio() is in the callchain. That works an enables
  my "dream" implementation above where we use an "init" state to
  solve this. However, it's nice not to have to do this. By handling
  just the first transition to GPIO we can simply let the normal
  "default" remuxing happen and we can be assured that there won't be
  a glitch.

Before this change I could see the glitch reported on the EC console
when booting. It would say this when booting the kernel:
  Unexpected state 1 in CSNRE ISR

After this change there is no error reported.

Note that I haven't reproduced the original problem described in
e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at
bootup on trogdor") but I could believe it might happen in certain
timing conditions.

Fixes: b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf separately")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20221014103217.1.I656bb2c976ed626e5d37294eb252c1cf3be769dc@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 9989bc33c4894e0751679b91fc6eb585772487b9 upstream.

This reverts commit ad2bea79ef0144043721d4893eef719c907e2e63.

On systems with older PMUFW (Xilinx ZynqMP Platform Management Firmware)
using these pinctrl properties can cause system hang because there is
missing feature autodetection.
When this feature is implemented in the PMUFW, support for these two
properties should bring back.

Cc: stable@vger.kernel.org
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221017130303.21746-2-sai.krishna.potthuri@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 17747577bbcb496e1b1c4096d64c2fc1e7bc0fef upstream.

Fixes UART1 function bits and MMC groups typo.

For pins 0x97,0x99 function 0 is designated to PWM3/PWM5
respectively, function is 1 designated to the UART1.

Diff from v1:
 - sent separately
 - added tag Fixes

Cc: stable@vger.kernel.org
Fixes: b582b5a434d3 ("pinctrl: Ingenic: Add pinctrl driver for JZ4755.")
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016153548.3024209-1-lis8215@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3160b37e5cb695e866e06c3fdbc385846b569294 upstream.

Use dev_dbg instead of dev_warn for additional support of pinmux
feature.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20220830110525.1933198-1-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4635c0e2a7f7f3568cbfccae70121f9835efa62c upstream.

Before the split of gpio and pinctrl sections in their own driver,
rockchip_set_mux was called in pinmux_ops.gpio_set_direction for
configuring a pin in its GPIO function.

This is essential for cases where pinctrl is "bypassed" by gpio
consumers otherwise the GPIO function is not configured for the pin and
it does not work. Such was the case for the sysfs/libgpiod userspace
GPIO handling.

Let's re-implement the pinmux_ops.gpio_set_direction callback so that
the gpio subsystem can request from the pinctrl driver to put the pin in
its GPIO function.

Fixes: 9ce9a02039de ("pinctrl/rockchip: drop the gpio related codes")
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220930132033.4003377-2-foss+kernel@0leil.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When an external device generated a level based interrupt then the
interrupt controller could miss the interrupt. The reason is that the
interrupt controller can detect only link changes.

In the following example, if there is a PHY that generates an interrupt
then the following would happen. The GPIO detected that the interrupt
line changed, and then the 'ocelot_irq_handler' was called. Here it
detects which GPIO line saw the change and for that will call the
following:
1. irq_mask
2. phy interrupt routine
3. irq_eoi
4. irq_unmask

And this works fine for simple cases, but if the PHY generates many
interrupts, for example when doing PTP timestamping, then the following
could happen. Again the function 'ocelot_irq_handler' will be called
and then from here the following could happen:
1. irq_mask
2. phy interrupt routine
3. irq_eoi
4. irq_unmask

Right before step 3(irq_eoi), the PHY will generate another interrupt.
Now the interrupt controller will acknowledge the change in the
interrupt line. So we miss the interrupt.

A solution will be to use 'handle_level_irq' instead of
'handle_fasteoi_irq', because for this will change routine order of
handling the interrupt.
1. irq_mask
2. irq_ack
3. phy interrupt routine
4. irq_unmask

And now if the PHY will generate a new interrupt before irq_unmask, the
interrupt controller will detect this because it already acknowledge the
change in interrupt line at step 2(irq_ack).

But this is not the full solution because there is another issue. In
case there are 2 PHYs that share the interrupt line. For example phy1
generates an interrupt, then the following can happen:
1.irq_mask
2.irq_ack
3.phy0 interrupt routine
4.phy1 interrupt routine
5.irq_unmask

In case phy0 will generate an interrupt while clearing the interrupt
source in phy1, then the interrupt line will be kept down by phy0. So
the interrupt controller will not see any changes in the interrupt line.
The solution here is to update 'irq_unmask' such that it can detect if
the interrupt line is still active or not. And if it is active then call
again the procedure to clear the interrupts. But we don't want to do it
every time, only if we know that the interrupt controller has not seen
already that the interrupt line has changed.

While at this, add support also for IRQ_TYPE_LEVEL_LOW.

Fixes: be36abb71d878f ("pinctrl: ocelot: add support for interrupt controller")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220909145942.844102-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The name of A100 R_PIO driver should be sun50i-a100-r-pinctrl,
not sun50iw10p1-r-pinctrl.

Fixes: 473436e7647d6 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220819024541.74191-1-michael@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pin numbers for UFS_RESET and SDC2_* are not
consistent in the pinctrl driver for sc8180x.
So fix it.

Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec4b ("pinctrl: qcom: Add sc8180x TLMM driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-3-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently in the wakeirq_map, gpio36 and gpio37 have the same wakeirq
number, resulting in gpio37 being unable to trigger interrupts.
It looks like that this is a typo in the wakeirq map. So fix it.

Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec4b ("pinctrl: qcom: Add sc8180x TLMM driver")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-2-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>