linux-stable.git/drivers/pinctrl, branch v5.8.2 Linux kernel stable tree pinctrl-single: fix pcs_parse_pinconf() return value 2020-08-19T06:26:57+00:00 Drew Fustini drew@beagleboard.org 2020-06-08T12:51:43+00:00 a75fc224ebe8088595883dd1f30ff8ee1a20d5e5 [ Upstream commit f46fe79ff1b65692a65266a5bec6dbe2bf7fc70f ] This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2. Analysis: ========= The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2: 980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs, 981 struct device_node *np, 982 struct pinctrl_map **map, 983 unsigned *num_maps, 984 const char **pgnames) 985 { <snip> 1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP; 1054 (*map)->data.mux.group = np->name; 1055 (*map)->data.mux.function = np->name; 1056 1057 if (PCS_HAS_PINCONF && function) { 1058 res = pcs_parse_pinconf(pcs, np, function, map); 1059 if (res) 1060 goto free_pingroups; 1061 *num_maps = 2; 1062 } else { 1063 *num_maps = 1; 1064 } However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940: 895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np, 896 struct pcs_function *func, 897 struct pinctrl_map **map) 898 899 { 900 struct pinctrl_map *m = *map; <snip> 917 /* If pinconf isn't supported, don't parse properties in below. */ 918 if (!PCS_HAS_PINCONF) 919 return 0; 920 921 /* cacluate how much properties are supported in current node */ 922 for (i = 0; i < ARRAY_SIZE(prop2); i++) { 923 if (of_find_property(np, prop2[i].name, NULL)) 924 nconfs++; 925 } 926 for (i = 0; i < ARRAY_SIZE(prop4); i++) { 927 if (of_find_property(np, prop4[i].name, NULL)) 928 nconfs++; 929 } 930 if (!nconfs) 919 return 0; 932 933 func->conf = devm_kcalloc(pcs->dev, 934 nconfs, sizeof(struct pcs_conf_vals), 935 GFP_KERNEL); 936 if (!func->conf) 937 return -ENOMEM; 938 func->nconfs = nconfs; 939 conf = &(func->conf[0]); 940 m++; This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single". The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added. Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties. [0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/ Fixes: 9dddb4df90d1 ("pinctrl: single: support generic pinconf") Signed-off-by: Drew Fustini <drew@beagleboard.org> Acked-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1 Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f46fe79ff1b65692a65266a5bec6dbe2bf7fc70f ]

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no
pinctrl_map is added.  The current behavior is to return 0 when
!PCS_HAS_PINCONF or !nconfs.  Thus pcs_parse_one_pinctrl_entry()
incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf()
if PCS_HAS_PINCONF is enabled.  The function pcs_parse_pinconf()
returns 0 to indicate there was no error and num_maps is then set to 2:

 980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;
1056
1057         if (PCS_HAS_PINCONF && function) {
1058                 res = pcs_parse_pinconf(pcs, np, function, map);
1059                 if (res)
1060                         goto free_pingroups;
1061                 *num_maps = 2;
1062         } else {
1063                 *num_maps = 1;
1064         }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or
!nconfs.  I believe these conditions should indicate that no map was
added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry()
will set num_maps = 2 even though no maps were successfully added, as
it does not reach "m++" on line 940:

 895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
 896                              struct pcs_function *func,
 897                              struct pinctrl_map **map)
 898
 899 {
 900         struct pinctrl_map *m = *map;
<snip>
 917         /* If pinconf isn't supported, don't parse properties in below. */
 918         if (!PCS_HAS_PINCONF)
 919                 return 0;
 920
 921         /* cacluate how much properties are supported in current node */
 922         for (i = 0; i < ARRAY_SIZE(prop2); i++) {
 923                 if (of_find_property(np, prop2[i].name, NULL))
 924                         nconfs++;
 925         }
 926         for (i = 0; i < ARRAY_SIZE(prop4); i++) {
 927                 if (of_find_property(np, prop4[i].name, NULL))
 928                         nconfs++;
 929         }
 930         if (!nconfs)
 919                 return 0;
 932
 933         func->conf = devm_kcalloc(pcs->dev,
 934                                   nconfs, sizeof(struct pcs_conf_vals),
 935                                   GFP_KERNEL);
 936         if (!func->conf)
 937                 return -ENOMEM;
 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black
(AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi
has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF
or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no
map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish
between -ENOSUPP and other errors.  In the case of -ENOSUPP, num_maps
is set to 1 as it is valid for pinconf to be enabled and a given pin
group to not any pinconf properties.

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes: 9dddb4df90d1 ("pinctrl: single: support generic pinconf")
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Merge tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl 2020-08-01T17:11:42+00:00 Linus Torvalds torvalds@linux-foundation.org 2020-08-01T17:11:42+00:00 d52daa8620c65960e1ef882adc1f92061326bd7a Pull pin control fix from Linus Walleij: "A single last minute pin control fix to the Qualcomm driver fixing missing dual edge PCH interrupts" * tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180 
Pull pin control fix from Linus Walleij:
 "A single last minute pin control fix to the Qualcomm driver fixing
  missing dual edge PCH interrupts"

* tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180
pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180 2020-07-16T13:41:41+00:00 Douglas Anderson dianders@chromium.org 2020-07-14T15:04:17+00:00 c3c0c2e18d943ec4a84162ac679970b592555a4a Depending on how you look at it, you can either say that: a) There is a PDC hardware issue (with the specific IP rev that exists on sc7180) that causes the PDC not to work properly when configured to handle dual edges. b) The dual edge feature of the PDC hardware was only added in later HW revisions and thus isn't in all hardware. Regardless of how you look at it, let's work around the lack of dual edge support by only ever letting our parent see requests for single edge interrupts on affected hardware. NOTE: it's possible that a driver requesting a dual edge interrupt might get several edges coalesced into a single IRQ. For instance if a line starts low and then goes high and low again, the driver that requested the IRQ is not guaranteed to be called twice. However, it is guaranteed that once the driver's interrupt handler starts running its first instruction that any new edges coming in will cause the interrupt to fire again. This is relatively commonplace for dual-edge gpio interrupts (many gpio controllers require software to emulate dual edge with single edge) so client drivers should be setup to handle it. Fixes: e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200714080254.v3.1.Ie0d730120b232a86a4eac1e2909bcbec844d1766@changeid Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Depending on how you look at it, you can either say that:
a) There is a PDC hardware issue (with the specific IP rev that exists
   on sc7180) that causes the PDC not to work properly when configured
   to handle dual edges.
b) The dual edge feature of the PDC hardware was only added in later
   HW revisions and thus isn't in all hardware.

Regardless of how you look at it, let's work around the lack of dual
edge support by only ever letting our parent see requests for single
edge interrupts on affected hardware.

NOTE: it's possible that a driver requesting a dual edge interrupt
might get several edges coalesced into a single IRQ.  For instance if
a line starts low and then goes high and low again, the driver that
requested the IRQ is not guaranteed to be called twice.  However, it
is guaranteed that once the driver's interrupt handler starts running
its first instruction that any new edges coming in will cause the
interrupt to fire again.  This is relatively commonplace for dual-edge
gpio interrupts (many gpio controllers require software to emulate
dual edge with single edge) so client drivers should be setup to
handle it.

Fixes: e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200714080254.v3.1.Ie0d730120b232a86a4eac1e2909bcbec844d1766@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge tag 'intel-pinctrl-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes 2020-06-27T23:08:21+00:00 Linus Walleij linus.walleij@linaro.org 2020-06-27T23:08:21+00:00 f8e99dde21995d185e2379e34ea2b96acf85702b intel-pinctrl for v5.8-2 * Fix output pin value handling on Intel Baytrail The following is an automated git shortlog grouped by driver: baytrail: - Fix pin being driven low for a while on gpiod_get(..., GPIOD_OUT_HIGH) 
intel-pinctrl for v5.8-2

* Fix output pin value handling on Intel Baytrail

The following is an automated git shortlog grouped by driver:

baytrail:
 -  Fix pin being driven low for a while on gpiod_get(..., GPIOD_OUT_HIGH)
pinctrl: baytrail: Fix pin being driven low for a while on gpiod_get(..., GPIOD_OUT_HIGH) 2020-06-26T11:20:00+00:00 Hans de Goede hdegoede@redhat.com 2020-06-06T09:31:50+00:00 45c11a927606c612e4898a9484867b71318699f6 The pins on the Bay Trail SoC have separate input-buffer and output-buffer enable bits and a read of the level bit of the value register will always return the value from the input-buffer. The BIOS of a device may configure a pin in output-only mode, only enabling the output buffer, and write 1 to the level bit to drive the pin high. This 1 written to the level bit will be stored inside the data-latch of the output buffer. But a subsequent read of the value register will return 0 for the level bit because the input-buffer is disabled. This causes a read-modify-write as done by byt_gpio_set_direction() to write 0 to the level bit, driving the pin low! Before this commit byt_gpio_direction_output() relied on pinctrl_gpio_direction_output() to set the direction, followed by a call to byt_gpio_set() to apply the selected value. This causes the pin to go low between the pinctrl_gpio_direction_output() and byt_gpio_set() calls. Change byt_gpio_direction_output() to directly make the register modifications itself instead. Replacing the 2 subsequent writes to the value register with a single write. Note that the pinctrl code does not keep track internally of the direction, so not going through pinctrl_gpio_direction_output() is not an issue. This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is already on at boot (no external monitor connected), then the i915 driver does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The temporarily going low of that GPIO was causing the panel to reset itself after which it would not show an image until it was turned off and back on again (until a full modeset was done on it). This commit fixes this. This commit also updates the byt_gpio_direction_input() to use direct register accesses instead of going through pinctrl_gpio_direction_input(), to keep it consistent with byt_gpio_direction_output(). Note for backporting, this commit depends on: commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output") Cc: stable@vger.kernel.org Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> 
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.

The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.

But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!

Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.

Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.

Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.

This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.

This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().

Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")

Cc: stable@vger.kernel.org
Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
pinctrl: amd: fix npins for uart0 in kerncz_groups 2020-06-22T07:35:39+00:00 Jacky Hu hengqing.hu@gmail.com 2020-06-16T01:50:24+00:00 69339d083dfb7786b0e0b3fc19eaddcf11fabdfb uart0_pins is defined as: static const unsigned uart0_pins[] = {135, 136, 137, 138, 139}; which npins is wronly specified as 9 later { .name = "uart0", .pins = uart0_pins, .npins = 9, }, npins should be 5 instead of 9 according to the definition. Signed-off-by: Jacky Hu <hengqing.hu@gmail.com> Link: https://lore.kernel.org/r/20200616015024.287683-1-hengqing.hu@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
uart0_pins is defined as:
static const unsigned uart0_pins[] = {135, 136, 137, 138, 139};

which npins is wronly specified as 9 later
	{
		.name = "uart0",
		.pins = uart0_pins,
		.npins = 9,
	},

npins should be 5 instead of 9 according to the definition.

Signed-off-by: Jacky Hu <hengqing.hu@gmail.com>
Link: https://lore.kernel.org/r/20200616015024.287683-1-hengqing.hu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: single: fix function name in documentation 2020-06-20T20:41:32+00:00 Drew Fustini drew@beagleboard.org 2020-06-12T11:27:58+00:00 25fae752156db7253471347df08a2700501eafde Use the correct the function name in the documentation for "pcs_parse_one_pinctrl_entry()". "smux_parse_one_pinctrl_entry()" appears to be an artifact from the development of a prior patch series ("simple pinmux driver") which transformed into pinctrl-single. Signed-off-by: Drew Fustini <drew@beagleboard.org> Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1 Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Use the correct the function name in the documentation for
"pcs_parse_one_pinctrl_entry()".

"smux_parse_one_pinctrl_entry()" appears to be an artifact from the
development of a prior patch series ("simple pinmux driver") which
transformed into pinctrl-single.

Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: qcom: ipq6018 Add missing pins in qpic pin group 2020-06-20T20:05:24+00:00 Sivaprakash Murugesan sivaprak@codeaurora.org 2020-06-19T04:31:29+00:00 7f5f4de83ca30a4922bb178b80144e2778faad01 The patch adds missing qpic data pins to qpic pingroup. These pins are necessary for the qpic nand to work. Fixes: ef1ea54eab0e ("pinctrl: qcom: Add ipq6018 pinctrl driver") Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Link: https://lore.kernel.org/r/1592541089-17700-1-git-send-email-sivaprak@codeaurora.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
The patch adds missing qpic data pins to qpic pingroup. These pins are
necessary for the qpic nand to work.

Fixes: ef1ea54eab0e ("pinctrl: qcom: Add ipq6018 pinctrl driver")
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1592541089-17700-1-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Revert "pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'" 2020-06-20T20:04:39+00:00 Haibo Chen haibo.chen@nxp.com 2020-06-09T03:27:03+00:00 13f2d25b951f139064ec2dd53c0c7ebdf8d8007e This reverts commit ba403242615c2c99e27af7984b1650771a2cc2c9. After commit 26d8cde5260b ("pinctrl: freescale: imx: add shared input select reg support"). i.MX7D has two iomux controllers iomuxc and iomuxc-lpsr which share select_input register for daisy chain settings. If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call devm_request_mem_region() for the region <0x30330000-0x3033ffff> for the first time. Then, next time when probe the iomuxc, API devm_platform_ioremap_resource() will also use the API devm_request_mem_region() for the share region <0x30330000-0x3033ffff> again, then cause issue, log like below: [ 0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver [ 0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff] [ 0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16 Fixes: ba403242615c ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
This reverts commit ba403242615c2c99e27af7984b1650771a2cc2c9.

After commit 26d8cde5260b ("pinctrl: freescale: imx: add shared
input select reg support"). i.MX7D has two iomux controllers
iomuxc and iomuxc-lpsr which share select_input register for
daisy chain settings.
If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call
devm_request_mem_region() for the region <0x30330000-0x3033ffff>
for the first time. Then, next time when probe the iomuxc, API
devm_platform_ioremap_resource() will also use the API
devm_request_mem_region() for the share region <0x30330000-0x3033ffff>
again, then cause issue, log like below:

[    0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[    0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff]
[    0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16

Fixes: ba403242615c ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: mcp23s08: Split to three parts: fix ptr_ret.cocci warnings 2020-06-16T08:19:53+00:00 kernel test robot lkp@intel.com 2020-06-08T01:02:53+00:00 3e5b8f87994e1269a7a9ea1862df163b110932eb drivers/pinctrl/pinctrl-mcp23s08_spi.c:129:1-3: WARNING: PTR_ERR_OR_ZERO can be used Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR Generated by: scripts/coccinelle/api/ptr_ret.cocci Fixes: 0f04a81784fe ("pinctrl: mcp23s08: Split to three parts: core, I²C, SPI") Signed-off-by: kernel test robot <lkp@intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200608010253.GA79576@44f7ab9e8d59 Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
drivers/pinctrl/pinctrl-mcp23s08_spi.c:129:1-3: WARNING: PTR_ERR_OR_ZERO can be used

 Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci

Fixes: 0f04a81784fe ("pinctrl: mcp23s08: Split to three parts: core, I²C, SPI")
Signed-off-by: kernel test robot <lkp@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200608010253.GA79576@44f7ab9e8d59
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>