linux-stable.git/drivers/pinctrl, branch v4.7.2

pinctrl: cherryview: prevent concurrent access to GPIO controllers

2016-08-20T16:10:50+00:00

commit 0bd50d719b004110e791800450ad204399100a86 upstream.

Due to a silicon issue on the Atom X5-Z8000 "Cherry Trail" processor
series, a common lock must be used to prevent concurrent accesses
across the 4 GPIO controllers managed by this driver.

See Intel Atom Z8000 Processor Series Specification Update
(Rev. 005), errata #CHT34, for further information.

Signed-off-by: Dan O'Donovan 
Acked-by: Mika Westerberg 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: baytrail: Fix mingled clock pins

2016-06-23T09:05:04+00:00

Fix plt clock 3, 4 and 5 pins, which were not in the proper order.

Signed-off-by: Cristina Ciocan 
Acked-by: Mika Westerberg 
Signed-off-by: Linus Walleij

pinctrl: tegra: Fix build dependency

2016-06-22T15:58:07+00:00

I got below build error:
ERROR: "tegra_xusb_padctl_legacy_probe"
 [drivers/phy/tegra/phy-tegra-xusb.ko] undefined!
with below build configuration:
CONFIG_ARCH_TEGRA=y
CONFIG_PINCTRL_TEGRA_XUSB=y
CONFIG_PHY_TEGRA_XUSB=y

The problem is below line in drivers/pinctrl/Makefile
obj-$(CONFIG_PINCTRL_TEGRA)     += tegra/

So even CONFIG_PINCTRL_TEGRA_XUSB=y is set, kbuild still does not compile
the code in drivers/pinctrl/tegra folder if !CONFIG_PINCTRL_TEGRA.

phy-tegra-xusb.c does not use any symbol from pinctrl-tegra.c,
so build pinctrl-tegra.c only when CONFIG_PINCTRL_TEGRA is set.

Signed-off-by: Axel Lin 
Acked-by: Jon Hunter 
Signed-off-by: Linus Walleij

pinctrl: single: Fix missing flush of posted write for a wakeirq

2016-06-22T15:58:07+00:00

With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.

Let's fix the issue with a flush of posted write with a readback.

Cc: stable@vger.kernel.org
Reported-by: Nishanth Menon 
Signed-off-by: Tony Lindgren 
Signed-off-by: Linus Walleij

pinctrl: imx: Do not treat a PIN without MUX register as an error

2016-06-22T15:58:06+00:00

Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.

Cc: stable@vger.kernel.org
Signed-off-by: Alexander Shiyan 
Signed-off-by: Linus Walleij

pinctrl: mediatek: fix dual-edge code defect

2016-05-31T08:13:45+00:00

When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.

Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao 
Reviewed-by: Matthias Brugger 
Signed-off-by: Linus Walleij

pinctrl: nomadik: fix inversion of gpio direction

2016-05-30T07:42:37+00:00

The input/output directions were inversed on the GPIO direction
read function. Loose a ! and it is correct.

Signed-off-by: Linus Walleij

drivers/pinctrl/intel/pinctrl-baytrail.c: fix build with gcc-4.4

2016-05-26T22:35:44+00:00

gcc-4.4 and thereabouts has issues with initializers of anonymous
unions, and it generates the following warnings:

  drivers/pinctrl/intel/pinctrl-baytrail.c:413: error: unknown field 'simple_funcs' specified in initializer
  drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: missing braces around initializer
  drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: (near initialization for 'byt_score_groups[0].')
  drivers/pinctrl/intel/pinctrl-baytrail.c:415: error: unknown field 'simple_funcs' specified in initializer
  drivers/pinctrl/intel/pinctrl-baytrail.c:417: error: unknown field 'simple_funcs' specified in initializer
  ...

Work around this.

Acked-by: Mika Westerberg 
Cc: Heikki Krogerus 
Cc: Linus Walleij 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2016-05-19T19:50:56+00:00

Pull pin control updates from Linus Walleij:
 "This kernel cycle was quite calm when it comes to pin control and
  there is really just one major change, and that is the introduction of
  devm_pinctrl_register() managed resources.

  Apart from that linear development, details below.

  Core changes:

   - Add the devm_pinctrl_register() API and switch all applicable
     drivers to use it, saving lots of lines of code all over the place.

  New drivers:

   - driver for the Broadcom NS2 SoC

   - subdriver for the PXA25x SoCs

   - subdriver for the AMLogic Meson GXBB SoC

  Driver improvements:

   - the Intel Baytrail driver now properly supports pin control

   - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
     callback in the GPIO portions

   - continued development and stabilization of several SH-PFC SoC
     subdrivers: r8a7795, r8a7790, r8a7794 etc"

* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
  Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
  pinctrl: meson: Fix eth_tx_en bit index
  pinctrl: tegra: avoid parked_reg and parked_bank
  pinctrl: tegra: Correctly check the supported configuration
  pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
  pinctrl: rockchip: fix pull setting error for rk3399
  pinctrl: stm32: Implement .pin_config_dbg_show()
  pinctrl: nomadik: hide nmk_gpio_get_mode when unused
  pinctrl: ns2: rename pinctrl_utils_dt_free_map
  pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
  pinctrl: at91: Make at91_gpio_template const
  pinctrl: baytrail: fix some error handling in debugfs
  pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
  pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
  pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
  pinctrl: nomadik: implement .get_direction()
  pinctrl: nomadik: use BIT() with offsets consequently
  pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
  pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
  pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
  ...

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2016-05-18T20:14:02+00:00

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, these contain various things that touch
  the drivers/ directory but got merged through arm-soc for practical
  reasons.

  For the most part, this is now related to power management
  controllers, which have not yet been abstracted into a separate
  subsystem, and typically require some code in drivers/soc or arch/arm
  to control the power domains.

  Another large chunk here is a rework of the NVIDIA Tegra USB3.0
  support, which was surprisingly tricky and took a long time to get
  done.

  Finally, reset controller handling as always gets merged through here
  as well"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
  arm-ccn: Enable building as module
  soc/tegra: pmc: Add generic PM domain support
  usb: xhci: tegra: Add Tegra210 support
  usb: xhci: Add NVIDIA Tegra XUSB controller driver
  dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
  dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
  PCI: tegra: Support per-lane PHYs
  dt-bindings: pci: tegra: Update for per-lane PHYs
  phy: tegra: Add Tegra210 support
  phy: Add Tegra XUSB pad controller support
  dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
  dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
  phy: core: Allow children node to be overridden
  clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
  drivers: firmware: psci: make two helper functions inline
  soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
  soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
  soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
  soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
  soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
  ...