linux-stable.git/drivers/pinctrl, branch v4.14.78

pinctrl: mcp23s08: fix irq and irqchip setup order

2018-10-18T07:16:24+00:00

commit f259f896f2348f0302f6f88d4382378cf9d23a7e upstream.

Since 'commit 02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")' the
irq request isn't the last devm_* allocation. Without a deeper look at
the irq and testing this isn't a good solution. Since this driver relies
on the devm mechanism, requesting a interrupt should be the last thing
to avoid memory corruptions during unbinding.

'Commit 02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")' fixed the
order for the interrupt-controller use case only. The
mcp23s08_irq_setup() must be split into two to fix it for the
interrupt-controller use case and to register the irq at last. So the
irq will be freed first during unbind.

Cc: stable@vger.kernel.org
Cc: Jan Kundrát 
Cc: Dmitry Mastykin 
Cc: Sebastian Reichel 
Fixes: 82039d244f87 ("pinctrl: mcp23s08: add pinconf support")
Fixes: 02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")
Signed-off-by: Marco Felsch 
Tested-by: Phil Reid 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant

2018-09-26T06:38:13+00:00

[ Upstream commit 1cf86bc21257a330e3af51f2a4e885f1a705f6a5 ]

If you do this on an sdm845 board:
  grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE.  Oops.

Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: msm: Fix msm_config_group_get() to be compliant

2018-09-26T06:38:13+00:00

[ Upstream commit 05e0c828955c1cab58dd71a04539442e5375d917 ]

If you do this on an sdm845 board:
  cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias bus hold, input bias disabled, input bias pull down, input bias pull up

That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver")
Signed-off-by: Douglas Anderson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: rza1: Fix selector use for groups and functions

2018-09-26T06:38:10+00:00

[ Upstream commit dc4003d260594aa300028c3c5d040c5719abd19b ]

We must use a mutex around the generic_add functions and save the
function and group selector in case we need to remove them. Otherwise
the selector use will be racy for deferred probe at least.

Fixes: 5a49b644b307 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Reported-by: H. Nikolaus Schaller 
Cc: Christ van Willegen 
Cc: Haojian Zhuang 
Cc: Paul Cercueil 
Cc: Sean Wang 
Acked-by: Jacopo Mondi 
Signed-off-by: Tony Lindgren 
Tested-By: H. Nikolaus Schaller 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl/amd: only handle irq if it is pending and unmasked

2018-09-19T20:43:42+00:00

[ Upstream commit 8bbed1eef001fdfc0ee9595f64cc4f769d265af4 ]

The AMD pinctrl driver demultiplexes GPIO interrupts and fires off their
individual handlers.

If one of these GPIO irqs is configured as a level interrupt, and its
downstream handler is a threaded ONESHOT interrupt, the GPIO interrupt
source is masked by handle_level_irq() until the eventual return of the
threaded irq handler.  During this time the level GPIO interrupt status
will still report as high until the actual gpio source is cleared - both
in the individual GPIO interrupt status bit (INTERRUPT_STS_OFF) and in
its corresponding "WAKE_INT_STATUS_REG" bit.

Thus, if another GPIO interrupt occurs during this time,
amd_gpio_irq_handler() will see that the (masked-and-not-yet-cleared)
level irq is still pending and incorrectly call its handler again.

To fix this, have amd_gpio_irq_handler() check for both interrupts status
and mask before calling generic_handle_irq().

Note: Is it possible that this bug was the source of the interrupt storm
on Ryzen when using chained interrupts before commit ba714a9c1dea85
("pinctrl/amd: Use regular interrupt instead of chained")?

Signed-off-by: Daniel Kurtz 
Acked-by: Thomas Gleixner 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: imx: off by one in imx_pinconf_group_dbg_show()

2018-09-19T20:43:42+00:00

[ Upstream commit b4859f3edb47825f62d1b2efdd75fe7945996f49 ]

The > should really be >= here.  It's harmless because
pinctrl_generic_get_group() will return a NULL if group is invalid.

Fixes: ae75ff814538 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Reported-by: Dong Aisheng 
Signed-off-by: Dan Carpenter 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: freescale: off by one in imx1_pinconf_group_dbg_show()

2018-09-05T07:26:39+00:00

commit 19da44cd33a3a6ff7c97fff0189999ff15b241e4 upstream.

The info->groups[] array is allocated in imx1_pinctrl_parse_dt().  It
has info->ngroups elements.  Thus the > here should be >= to prevent
reading one element beyond the end of the array.

Cc: stable@vger.kernel.org
Fixes: 30612cd90005 ("pinctrl: imx1 core driver")
Signed-off-by: Dan Carpenter 
Reviewed-by: Uwe Kleine-König 
Acked-by: Dong Aisheng 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: nsp: Fix potential NULL dereference

2018-08-24T11:09:17+00:00

[ Upstream commit c29e9da56bebb4c2c794e871b0dc0298bbf08142 ]

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.

This is detected by Coccinelle semantic patch.

@@
expression pdev, res, n, t, e, e1, e2;
@@

res = platform_get_resource(pdev, t, n);
+ if (!res)
+   return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);

Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Wei Yongjun 
Reviewed-by: Ray Jui 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: nsp: off by ones in nsp_pinmux_enable()

2018-08-24T11:09:17+00:00

[ Upstream commit f90a21c898db58eaea14b8ad7e9af3b9e15e5f8a ]

The > comparisons should be >= or else we read beyond the end of the
pinctrl->functions[] array.

Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Dan Carpenter 
Reviewed-by: Ray Jui 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: ingenic: Fix inverted direction for < JZ4770

2018-08-24T11:09:17+00:00

[ Upstream commit 0084a786ca8c84b443f67c4a697b4f2552761650 ]

The .gpio_set_direction() callback was setting inverted direction
for SoCs older than the JZ4770, this restores the correct behaviour.

Signed-off-by: Paul Cercueil 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman