linux-stable.git/drivers/pinctrl/sunxi, branch linux-4.6.y

pinctrl: sunxi: Fix A33 external interrupts not working

2016-03-30T08:57:52+00:00

pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.

However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.

Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.

This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

2016-03-18T04:05:32+00:00

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for kernel v4.6.  There is quite a
  lot of interesting stuff going on.

  The patches to other subsystems and arch-wide are ACKed as far as
  possible, though I consider things like per-arch  as
  essentially a part of the GPIO subsystem so it should not be needed.

  Core changes:

   - The gpio_chip is now a *real device*.  Until now the gpio chips
     were just piggybacking the parent device or (gasp) floating in
     space outside of the device model.

     We now finally make GPIO chips devices.  The gpio_chip will create
     a gpio_device which contains a struct device, and this gpio_device
     struct is kept private.  Anything that needs to be kept private
     from the rest of the kernel will gradually be moved over to the
     gpio_device.

   - As a result of making the gpio_device a real device, we have added
     resource management, so devm_gpiochip_add_data() will cut down on
     overhead and reduce code lines.  A huge slew of patches convert
     almost all drivers in the subsystem to use this.

   - Building on making the GPIO a real device, we add the first step of
     a new userspace ABI: the GPIO character device.  We take small
     steps here, so we first add a pure *information* ABI and the tool
     "lsgpio" that will list all GPIO devices on the system and all
     lines on these devices.

     We can now discover GPIOs properly from userspace.  We still have
     not come up with a way to actually *use* GPIOs from userspace.

   - To encourage people to use the character device for the future, we
     have it always-enabled when using GPIO.  The old sysfs ABI is still
     opt-in (and can be used in parallel), but is marked as deprecated.

     We will keep it around for the foreseeable future, but it will not
     be extended to cover ever more use cases.

  Cleanup:

   - Bjorn Helgaas removed a whole slew of per-architecture 
     includes.

     This dates back to when GPIO was an opt-in feature and no shared
     library even existed: just a header file with proper prototypes was
     provided and all semantics were up to the arch to implement.  These
     patches make the GPIO chip even more a proper device and cleans out
     leftovers of the old in-kernel API here and there.

     Still some cruft is left but it's very little now.

   - There is still some clamping of return values for .get() going on,
     but we now return sane values in the vast majority of drivers and
     the errorpath is sanitized.  Some patches for powerpc, blackfin and
     unicore still drop in.

   - We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
     implementations to use gpiochip_add_data() and cut down on code
     lines.

   - MPC8xxx is converted to use the generic GPIO helpers.

   - ATH79 is converted to use the generic GPIO helpers.

  New drivers:

   - WinSystems WS16C48

   - Acces 104-DIO-48E

   - F81866 (a F7188x variant)

   - Qoric (a MPC8xxx variant)

   - TS-4800

   - SPI serializers (pisosr): simple 74xx shift registers connected to
     SPI to obtain a dirt-cheap output-only GPIO expander.

   - Texas Instruments TPIC2810

   - Texas Instruments TPS65218

   - Texas Instruments TPS65912

   - X-Gene (ARM64) standby GPIO controller"

* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
  Revert "Share upstreaming patches"
  gpio: mcp23s08: Fix clearing of interrupt.
  gpiolib: Fix comment referring to gpio_*() in gpiod_*()
  gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
  gpio: xgene: Fix kconfig for standby GIPO contoller
  gpio: Add generic serializer DT binding
  gpio: uapi: use 0xB4 as ioctl() major
  gpio: tps65912: fix bad merge
  Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
  gpio: omap: drop dev field from gpio_bank structure
  gpio: mpc8xxx: Slightly update the code for better readability
  gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
  gpio: mpc8xxx: Fixup setting gpio direction output
  gpio: mcp23s08: Add support for mcp23s18
  dt-bindings: gpio: altera: Fix altr,interrupt-type property
  gpio: add driver for MEN 16Z127 GPIO controller
  gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
  gpio: timberdale: Switch to devm_ioremap_resource()
  gpio: ts4800: Add IMX51 dependency
  gpiolib: rewrite gpiodev_add_to_list
  ...

drivers: pinctrl: add driver for Allwinner A64 SoC

2016-03-11T15:46:27+00:00

Based on the Allwinner A64 user manual and on the previous sunxi
pinctrl drivers this introduces the pin multiplex assignments for
the ARMv8 Allwinner A64 SoC.
Port A is apparently used for the fixed function DRAM controller, so
the ports start at B here (the manual mentions "n from 1 to 7", so
not starting at 0).

Signed-off-by: Andre Przywara 
Acked-by: Rob Herring 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

Merge tag 'v4.5-rc5' into devel

2016-03-10T02:29:25+00:00

Linux 4.5-rc5

pinctrl: sunxi: make A80 explicitly non-modular

2016-03-09T03:27:25+00:00

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN9I_A80_R
drivers/pinctrl/sunxi/Kconfig:  def_bool MACH_SUN9I

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Chen-Yu Tsai 
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

pinctrl: sunxi: does not need module.h

2016-03-09T03:22:47+00:00

This file is not modular, nor is it using modular functions. The
only thing close is the global THIS_MODULE which comes from export.h
so lets replace it appropriately and cut back on the amount of
header stuff we draw in by several thousand lines.

Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

pinctrl: sunxi: Change mux setting on PI irq pins

2016-03-08T09:02:27+00:00

While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".

This so called manual (A20 user manual v1.3 dated 2014-10-10) says:

Pin overview:
    Page 237:       EINT26 is on mux 5.
    Page 288:       EINT26 is on mux 6.

The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.

This patch is based on actual outcome of these tests and not what
the manual says.

Test procedure used:

Connect a 1 pulse per second (GPS) line to the pin.

echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge

Check /proc/interrupts if a irq was attached and if irq's where
received.

Hardware used:
Henry Paulissen: Cubietruck
Andere Przywara: BananaPi M1

Tested-by: Andre Przywara 
Reviewed-by: Andre Przywara 
Signed-off-by: Henry Paulissen 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

pinctrl: sunxi: Remove non existing irq's

2016-03-08T09:00:38+00:00

While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".

This so called manual (A20 user manual v1.3 dated 2014-10-10) says:

Pin overview:
    Page 233:       EINT12 is on pin PC19 mux6.
    Page 236:       EINT12 is on pin PH12 mux6.

Now, it is a bit strange to have the same IRQ on 2 different pins,
but I guess this could still be possible hardware wise. But then:

Pin registers:
    Page 253:       EINT12 is *not* on pin PC19.
    Page 281:       EINT12 is on pin PH12.

The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.

This patch is based on actual outcome of these tests and not what
the manual says.

Test procedure used:

Connect a 1 pulse per second (GPS) line to the pin.

echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge

Check /proc/interrupts if a irq was attached and if irq's where
received.

Signed-off-by: Henry Paulissen 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij

gpio/pinctrl: sunxi: stop poking around in private vars

2016-02-11T19:29:45+00:00

This kind of hacks disturbs the refactoring of the gpiolib.

The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.

Cc: Maxime Ripard 
Cc: Chen-Yu Tsai 
Signed-off-by: Linus Walleij

pinctrl: sunxi: Use pin number when calling sunxi_pmx_set

2016-02-11T13:30:29+00:00

sunxi_pmx_set accepts pin number and then calculates offset by
subtracting pin_base from it. sunxi_pinctrl_gpio_get, on the other hand,
gets offset so we have to convert it to pin number so we won't get
negative value in sunxi_pmx_set.

This was only used on A10 so far, where there is only one GPIO chip with
pin_base set to 0 so it didn't matter. However H3 also requires this
workaround but have two pinmux sections, triggering problem for PL port.

Signed-off-by: Krzysztof Adamski 
Acked-by: Chen-Yu Tsai 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij