linux-stable.git/drivers/pinctrl/qcom, branch v4.19.321

pinctrl: qcom: msm8916: Allow CAMSS GP clocks to be muxed

2022-08-25T09:15:37+00:00

commit 44339391c666e46cba522d19c65a6ad1071c68b7 upstream.

GPIO 31, 32 can be muxed to GCC_CAMSS_GP(1,2)_CLK respectively but the
function was never assigned to the pingroup (even though the function
exists already).

Add this mode to the related pins.

Fixes: 5373a2c5abb6 ("pinctrl: qcom: Add msm8916 pinctrl driver")
Signed-off-by: Nikita Travkin 
Link: https://lore.kernel.org/r/20220612145955.385787-4-nikita@trvn.ru
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: qcom: ssbi-gpio: fix gpio-hog related boot issues

2019-12-13T07:51:26+00:00

[ Upstream commit 7ed07855773814337b9814f1c3e866df52ebce68 ]

When attempting to setup up a gpio hog, device probing will repeatedly
fail with -EPROBE_DEFERED errors. It is caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.

See Christian Lamparter's commit a86caa9ba5d7 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.

I did not test this change against any hardware supported by this
particular driver, however I was able to validate this same fix works
for pinctrl-spmi-gpio.c using a LG Nexus 5 (hammerhead) phone.

Signed-off-by: Brian Masney 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin

pinctrl: qcom: spmi-gpio: fix gpio-hog related boot issues

2019-12-01T08:17:32+00:00

[ Upstream commit 149a96047237574b756d872007c006acd0cc6687 ]

When attempting to setup up a gpio hog, device probing would repeatedly
fail with -EPROBE_DEFERED errors. It was caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.

See Christian Lamparter's commit a86caa9ba5d7 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.

Signed-off-by: Brian Masney 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin

pinctrl: ssbi-gpio: Fix pm8xxx_pin_config_get() to be compliant

2018-11-13T19:08:29+00:00

[ Upstream commit b432414b996d32a1bd9afe2bd595bd5729c1477f ]

If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.

The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem.  Let's fix it there too.

Fixes: b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Douglas Anderson 
Reviewed-by: Stephen Boyd 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: spmi-mpp: Fix pmic_mpp_config_get() to be compliant

2018-11-13T19:08:29+00:00

[ Upstream commit 0d5b476f8f57fcb06c45fe27681ac47254f63fd2 ]

If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.

The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem.  Let's fix it there too.

NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute.  If the last element (has_arg) is false then you need
to do the -EINVAL trick.

ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that.  It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.

Fixes: cfb24f6ebd38 ("pinctrl: Qualcomm SPMI PMIC MPP pin controller driver")
Signed-off-by: Douglas Anderson 
Reviewed-by: Stephen Boyd 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: qcom: spmi-mpp: Fix drive strength setting

2018-11-13T19:08:28+00:00

[ Upstream commit 89c68b102f13f123aaef22b292526d6b92501334 ]

It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.

Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Cc: Doug Anderson 
Signed-off-by: Stephen Boyd 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: qcom: spmi-mpp: Fix err handling of pmic_mpp_set_mux

2018-11-13T19:08:27+00:00

[ Upstream commit 69f8455f6cc78fa6cdf80d0105d7a748106271dc ]

'ret' should be returned while pmic_mpp_write_mode_ctl fails.

Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Signed-off-by: YueHaibing 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: msm: Really mask level interrupts to prevent latching

2018-08-29T07:38:50+00:00

The interrupt controller hardware in this pin controller has two status
enable bits. The first "normal" status enable bit enables or disables
the summary interrupt line being raised when a gpio interrupt triggers
and the "raw" status enable bit allows or prevents the hardware from
latching an interrupt into the status register for a gpio interrupt.
Currently we just toggle the "normal" status enable bit in the mask and
unmask ops so that the summary irq interrupt going to the CPU's
interrupt controller doesn't trigger for the masked gpio interrupt.

For a level triggered interrupt, the flow would be as follows: the pin
controller sees the interrupt, latches the status into the status
register, raises the summary irq to the CPU, summary irq handler runs
and calls handle_level_irq(), handle_level_irq() masks and acks the gpio
interrupt, the interrupt handler runs, and finally unmask the interrupt.
When the interrupt handler completes, we expect that the interrupt line
level will go back to the deasserted state so the genirq code can unmask
the interrupt without it triggering again.

If we only mask the interrupt by clearing the "normal" status enable bit
then we'll ack the interrupt but it will continue to show up as pending
in the status register because the raw status bit is enabled, the
hardware hasn't deasserted the line, and thus the asserted state latches
into the status register again. When the hardware deasserts the
interrupt the pin controller still thinks there is a pending unserviced
level interrupt because it latched it earlier. This behavior causes
software to see an extra interrupt for level type interrupts each time
the interrupt is handled.

Let's fix this by clearing the raw status enable bit for level type
interrupts so that the hardware stops latching the status of the
interrupt after we ack it. We don't do this for edge type interrupts
because it seems that toggling the raw status enable bit for edge type
interrupts causes spurious edge interrupts.

Signed-off-by: Stephen Boyd 
Reviewed-by: Douglas Anderson 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Linus Walleij

pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant

2018-07-09T11:16:01+00:00

If you do this on an sdm845 board:
  grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE.  Oops.

Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson 
Signed-off-by: Linus Walleij

pinctrl: msm: Fix msm_config_group_get() to be compliant

2018-07-09T11:14:09+00:00

If you do this on an sdm845 board:
  cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias bus hold, input bias disabled, input bias pull down, input bias pull up

That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver")
Signed-off-by: Douglas Anderson 
Signed-off-by: Linus Walleij