Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
Add the tsin pinctrl definitions needed for integrated DVB hardware support on Meson GXBB/GXL/GXM boards. changes in v2 - fix ordering and numbering of uart_c ping flagged by Otto in [1] [1] http://lists.infradead.org/pipermail/linux-amlogic/2020-March/015906.html Signed-off-by: Igor Vavro <afl2001@gmail.com> [updated commit message] Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Link: https://lore.kernel.org/r/1583377666-13378-1-git-send-email-christianshewitt@gmail.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
GPIOH_5 and GPIOH_6 can have two Ethernet related functions:
- GPIOH_5 can be ETH_TXD1 or ETH_RXD3
- GPIOH_6 can be ETH_TXD0 or ETH_RXD2
Add the bits for eth_rxd3_h and eth_rxd2_h so the ETH_RXD function can
be disabled when using the ETH_TXD function of GPIOH_{5,6}. No problem
was observed so far, but in theory this could lead to two different
signals being routed to the same pad (which could break Ethernet).
These settings were found in the public "Amlogic Ethernet controller
user guide":
http://openlinux.amlogic.com/@api/deki/files/75/=Amlogic_Ethenet_controller_user_Guide.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20191226191425.3797490-1-martin.blumenstingl@googlemail.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef37 ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch corrects the SPDX License Identifier style in header file related Meson axg SoC pinctrl driver. It assigns explicit block comment for the SPDX License Identifier. Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Link: https://lore.kernel.org/r/bcb86aa22d8d8499502bbd8c54a364be24886a86.1574871463.git.nishadkamdar@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Meson A1 SoC share the same register layout of pinmux with previous Meson-G12A, however there is difference for gpio and pin config register in A1. The main difference is that registers before A1 are grouped by function while those of A1 are by bank. The new register layout is as below: /* first bank */ /* addr */ - P_PADCTRL_GPIOP_I base + 0x00 << 2 - P_PADCTRL_GPIOP_O base + 0x01 << 2 - P_PADCTRL_GPIOP_OEN base + 0x02 << 2 - P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2 - P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2 - P_PADCTRL_GPIOP_DS base + 0x05 << 2 /* second bank */ - P_PADCTRL_GPIOB_I base + 0x10 << 2 - P_PADCTRL_GPIOB_O base + 0x11 << 2 - P_PADCTRL_GPIOB_OEN base + 0x12 << 2 - P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2 - P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2 - P_PADCTRL_GPIOB_DS base + 0x15 << 2 Each bank contains at least 6 registers to be configured, if one bank has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included. Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24 ,0x25 according to above register layout. For previous chips, registers are grouped according to their functions while registers of A1 are according to bank.Also note that there is no AO bank any more in A1. Current Meson pinctrl driver can cover such change by using base address of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen make wrong value to reg_ds for Socs that do not support drive-strength like AXG.To make things simple, add an extra dt parser function for a1 and remain the old dt parser function for only reg parsing. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and SoC relative fixup for AO. Several fixups in the same code make it hard to maintain, so move all fixups to each SoC's callback and make meson_pinctrl_parse_dt just do the reg parsing, separate these two parts.Overview of all current Meson SoCs fixup is as below: +------+--------------------------------------+--------------------------+ | | | | | SoC | EE domain | AO domain | +------+--------------------------------------+--------------------------+ |m8 | parse regs: | parse regs: | |m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)| |gxl | fixup: | fixup: | |gxbb | no | pull-enable = pull; | |axg | | | +------+--------------------------------------+--------------------------+ |g12a | parse regs: | parse regs: | |sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds | | | fixup: | fixup: | | | no | pull = gpio; | | | | pull-enable = gpio; | +------+--------------------------------------+--------------------------+ |a1 or | parse regs: | |later | gpio/mux (without ao domain) | |SoCs | fixup: | | | pull = gpio; pull-enable = gpio; ds = gpio; | +------+-----------------------------------------------------------------+ Since m8-axg share the same ao fixup, make a common function meson8_aobus_parse_dt_extra to do the job. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hi i tried to use the uart_C of the the odroid-c2.
I enabled it in the dts file. During boot it crashed when the
the sdcard slot is addressed.
After long search in the net i found this:
https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hilit=uart_C#p177856
After changing the pin definitions accordingly erverything works.
Uart_c is functioning and sdcard ist working.
Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins")
Signed-off-by: Otto Meier <gf435@gmx.net>
Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>