commit dc7a06b0dbbafac8623c2b7657e61362f2f479a7 upstream.
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef37 ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Meson A1 SoC share the same register layout of pinmux with previous Meson-G12A, however there is difference for gpio and pin config register in A1. The main difference is that registers before A1 are grouped by function while those of A1 are by bank. The new register layout is as below: /* first bank */ /* addr */ - P_PADCTRL_GPIOP_I base + 0x00 << 2 - P_PADCTRL_GPIOP_O base + 0x01 << 2 - P_PADCTRL_GPIOP_OEN base + 0x02 << 2 - P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2 - P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2 - P_PADCTRL_GPIOP_DS base + 0x05 << 2 /* second bank */ - P_PADCTRL_GPIOB_I base + 0x10 << 2 - P_PADCTRL_GPIOB_O base + 0x11 << 2 - P_PADCTRL_GPIOB_OEN base + 0x12 << 2 - P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2 - P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2 - P_PADCTRL_GPIOB_DS base + 0x15 << 2 Each bank contains at least 6 registers to be configured, if one bank has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included. Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24 ,0x25 according to above register layout. For previous chips, registers are grouped according to their functions while registers of A1 are according to bank.Also note that there is no AO bank any more in A1. Current Meson pinctrl driver can cover such change by using base address of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen make wrong value to reg_ds for Socs that do not support drive-strength like AXG.To make things simple, add an extra dt parser function for a1 and remain the old dt parser function for only reg parsing. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and SoC relative fixup for AO. Several fixups in the same code make it hard to maintain, so move all fixups to each SoC's callback and make meson_pinctrl_parse_dt just do the reg parsing, separate these two parts.Overview of all current Meson SoCs fixup is as below: +------+--------------------------------------+--------------------------+ | | | | | SoC | EE domain | AO domain | +------+--------------------------------------+--------------------------+ |m8 | parse regs: | parse regs: | |m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)| |gxl | fixup: | fixup: | |gxbb | no | pull-enable = pull; | |axg | | | +------+--------------------------------------+--------------------------+ |g12a | parse regs: | parse regs: | |sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds | | | fixup: | fixup: | | | no | pull = gpio; | | | | pull-enable = gpio; | +------+--------------------------------------+--------------------------+ |a1 or | parse regs: | |later | gpio/mux (without ao domain) | |SoCs | fixup: | | | pull = gpio; pull-enable = gpio; ds = gpio; | +------+-----------------------------------------------------------------+ Since m8-axg share the same ao fixup, make a common function meson8_aobus_parse_dt_extra to do the job. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hi i tried to use the uart_C of the the odroid-c2.
I enabled it in the dts file. During boot it crashed when the
the sdcard slot is addressed.
After long search in the net i found this:
https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hilit=uart_C#p177856
After changing the pin definitions accordingly erverything works.
Uart_c is functioning and sdcard ist working.
Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins")
Signed-off-by: Otto Meier <gf435@gmx.net>
Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in the case of a return from the middle of the loop, there is no put, thus causing a memory leak. Hence add an of_node_put before the return. Issue found with Coccinelle. Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Link: https://lore.kernel.org/r/20190815060718.3286-1-nishkadg.linux@gmail.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing pinmux for the pwm_a function on the GPIOE_2 pin. Reviewed-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20190729125838.6498-1-narmstrong@baylibre.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation you should have received a copy of the gnu general public license along with this program if not see http www gnu org licenses extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 30 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>