linux-stable.git/drivers/phy, branch v5.5.7

phy: qualcomm: Adjust indentation in read_poll_timeout

2020-02-11T12:37:18+00:00

commit a89806c998ee123bb9c0f18526e55afd12c0c0ab upstream.

Clang warns:

../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
                 usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
                 ^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
                if (readl_relaxed(addr) & mask)
                ^
1 warning generated.

This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.

Fixes: 1de990d8a169 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY")
Link: https://github.com/ClangBuiltLinux/linux/issues/816
Signed-off-by: Nathan Chancellor 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Greg Kroah-Hartman

phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz

2019-12-31T10:16:08+00:00

Commit 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.

When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.

Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.

Fixes: 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman 
Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Drop extra write to usb2 register

2019-12-26T10:57:53+00:00

We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.

Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Acked-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Improve host vs docked mode detection

2019-12-26T10:57:53+00:00

When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.

Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.

With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.

We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.

Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Acked-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Prevent USB line glitches from waking up modem

2019-12-26T10:57:53+00:00

The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.

We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.

Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.

Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Acked-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

phy: mapphone-mdm6600: Fix uninitialized status value regression

2019-12-26T10:57:53+00:00

Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.

And let's also drop useless debug code accidentally left over while
at it.

Fixes: b9762bebc633 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi 
Cc: Janusz Krzysztofik 
Cc: Linus Walleij 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Fix flakey host idling and enumerating of devices

2019-12-26T10:57:53+00:00

We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.

Cc: Jacopo Mondi 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Acked-by: Pavel Machek 
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

phy: qcom-qmp: Increase PHY ready timeout

2019-12-20T11:43:59+00:00

It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.

Signed-off-by: Bjorn Andersson 
Tested-by: Evan Green 
Tested-by: Vinod Koul 
Signed-off-by: Vinod Koul 
Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Fix error path when no host driver is loaded

2019-12-20T11:29:28+00:00

If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.

Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.

Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().

Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2019-12-05T19:43:31+00:00

Pull ARM SoC driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - A larger set of work on Tegra 2/3 around memory controller and
     regulator features, some fuse cleanups, etc..

   - MMP platform drivers, in particular for USB PHY, and other smaller
     additions.

   - Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
     and ASV (adaptive voltage), allowing the platform to run at more
     optimal operating points.

   - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas

   - Clock/reset control driver for TI/OMAP

   - Meson-A1 reset controller support

   - Qualcomm sdm845 and sda845 SoC IDs for socinfo"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
  firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
  soc: fsl: add RCPM driver
  dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
  memory: tegra: Consolidate registers definition into common header
  memory: tegra: Ensure timing control debug features are disabled
  memory: tegra: Introduce Tegra30 EMC driver
  memory: tegra: Do not handle error from wait_for_completion_timeout()
  memory: tegra: Increase handshake timeout on Tegra20
  memory: tegra: Print a brief info message about EMC timings
  memory: tegra: Pre-configure debug register on Tegra20
  memory: tegra: Include io.h instead of iopoll.h
  memory: tegra: Adapt for Tegra20 clock driver changes
  memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
  memory: tegra: Add gr2d and gr3d to DRM IOMMU group
  memory: tegra: Set DMA mask based on supported address bits
  soc: at91: Add Atmel SFR SN (Serial Number) support
  memory: atmel-ebi: switch to SPDX license identifiers
  memory: atmel-ebi: move NUM_CS definition inside EBI driver
  soc: mediatek: Refactor bus protection control
  soc: mediatek: Refactor sram control
  ...