linux-stable.git/drivers/phy, branch v4.19.100

phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal

2020-01-27T13:50:54+00:00

[ Upstream commit d9e100829fca6cbd270d7e005b0c0bb2d14924b8 ]

We are not destroying the sysfs attribute groupe we registered during
the probe function which will make subsequent probe calls to that
driver fail. Correct that with adding a remove function which only
removes those attributes since the reference counting on clocks did its
job already.

Fixes: 415060b21f31 ("phy: usb: phy-brcm-usb: Add ability to force DRD mode to host or device")
Signed-off-by: Florian Fainelli 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable

2020-01-27T13:50:52+00:00

[ Upstream commit d98010817a26eba8d4d1e8a639e0b7d7f042308a ]

The error return from the call to clk_prepare_enable is not being assigned
to variable ret even though ret is being used to check if the call failed.
Fix this by adding in the missing assignment.

Addresses-Coverity: ("Logically dead code")
Fixes: 891a96f65ac3 ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Colin Ian King 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: cpcap-usb: Fix flakey host idling and enumerating of devices

2020-01-14T19:07:08+00:00

commit 049226b9fd7442149dcbcf55f15408f5973cceda upstream.

We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.

Cc: Jacopo Mondi 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Acked-by: Pavel Machek 
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Greg Kroah-Hartman

phy: cpcap-usb: Fix error path when no host driver is loaded

2020-01-14T19:07:08+00:00

commit 4acb0200ab2b07843e3ef5599add3454c7440f03 upstream.

If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.

Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.

Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().

Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Signed-off-by: Tony Lindgren 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Greg Kroah-Hartman

phy: qcom-usb-hs: Fix extcon double register after power cycle

2019-12-31T15:35:30+00:00

[ Upstream commit 64f86b9978449ff05bfa6c64b4c5439e21e9c80b ]

Commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().

This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:

	double register detected
	WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
	Call trace:
	 ...
	 extcon_register_notifier+0x74/0xb8
	 devm_extcon_register_notifier+0x54/0xb8
	 qcom_usb_hs_phy_power_on+0x1fc/0x208
	 ...

... and USB stops working after plugging the cable out and in
another time.

The easiest way to fix this is to make a partial revert of
commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.

Fixes: f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: renesas: rcar-gen3-usb2: Fix sysfs interface of "role"

2019-12-17T19:34:45+00:00

commit 4bd5ead82d4b877ebe41daf95f28cda53205b039 upstream.

Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().

Reported-by: Pavel Machek 
Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc:  # v4.10+
Signed-off-by: Yoshihiro Shimoda 
Reviewed-by: Geert Uytterhoeven 
Acked-by: Pavel Machek 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Greg Kroah-Hartman

phy: lantiq: Fix compile warning

2019-11-20T17:47:35+00:00

[ Upstream commit 3a00dae006623d799266d85f28b5f76ef07d6b6c ]

This local variable is unused, remove it.

Fixes: dea54fbad332 ("phy: Add an USB PHY driver for the Lantiq SoCs using the RCU module")
Signed-off-by: Hauke Mehrtens 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: phy-twl4030-usb: fix denied runtime access

2019-11-20T17:47:24+00:00

[ Upstream commit 6c7103aa026094a4ee2c2708ec6977a6dfc5331d ]

When runtime is not enabled, pm_runtime_get_sync() returns -EACCESS,
the counter will be incremented but the resume callback not called,
so enumeration and charging will not start properly.
To avoid that happen, disable irq on suspend and recheck on resume.

Practically this happens when the device is woken up from suspend by
plugging in usb.

Signed-off-by: Andreas Kemnade 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: renesas: rcar-gen3-usb2: fix vbus_ctrl for role sysfs

2019-11-20T17:47:24+00:00

[ Upstream commit 09938ea9d136243e8d1fed6d4d7a257764f28f6d ]

This patch fixes and issue that the vbus_ctrl is disabled by
rcar_gen3_init_from_a_peri_to_a_host(), so a usb host cannot
supply the vbus.

Note that this condition will exit when the otg irq happens
even if we don't apply this patch.

Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Signed-off-by: Yoshihiro Shimoda 
Reviewed-by: Simon Horman 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin

phy: brcm-sata: allow PHY_BRCM_SATA driver to be built for DSL SoCs

2019-11-20T17:47:23+00:00

[ Upstream commit 26728df4b254ae06247726a9a6e64823e39ac504 ]

Broadcom ARM-based DSL SoCs (BCM63xx product line) have the same
Broadcom SATA PHY that other SoCs are using, make it possible to select
that driver on these platforms.

Signed-off-by: Florian Fainelli 
Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Sasha Levin