Commit b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in
wiz driver") added support for USXGMII mode. In doing so, P0_REFCLK_SEL
was set to "pcs_mac_clk_divx1_ln_0" (0x3) and P0_STANDARD_MODE was set to
LANE_MODE_GEN1, which results in a data rate of 5.15625 Gbps. However,
since the USXGMII mode can support up to 10.3125 Gbps data rate, the
aforementioned fields should be set to "pcs_mac_clk_divx0_ln_0" (0x2) and
LANE_MODE_GEN2 respectively. The signal corresponding to the USXGMII lane
of the SERDES has been measured as 5 Gbps without the change and 10 Gbps
with the change. Hence, fix the configuration accordingly to support
USXGMII up to 10G.

Fixes: b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in wiz driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241012053937.3596885-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Pull phy updates from Vinod Koul:
 "New hw support:
   - Rcar usb2 support for RZ/G3S SoC
   - Nuvoton MA35 SoC USB 2.0 PHY driver

  Removed:
   - obsolete qcom,usb-8x16-phy bindings

  Updates:
   - 4 lane PCIe support for Qualcomm X1E80100
   - Constify structure in subsystem update
   - Subsystem simplification with scoped for each OF child loop update
   - Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
     bindings"

* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
  phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
  dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
  phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
  phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
  phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
  phy: ti: gmii-sel: Simplify with dev_err_probe()
  phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
  phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
  phy: mediatek: xsphy: Simplify with scoped for each OF child loop
  phy: mediatek: tphy: Simplify with scoped for each OF child loop
  phy: hisilicon: usb2: Simplify with scoped for each OF child loop
  phy: cadence: sierra: Simplify with scoped for each OF child loop
  phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
  phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
  phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
  dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
  phy: qcom: qmp-pcie: Configure all tables on port B PHY
  phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
  dt-bindings: phy: socionext,uniphier: add top-level constraints
  phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
  ...

The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.

This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.

This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-11-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Drop OF node reference immediately after using it in
syscon_node_to_regmap(), which is both simpler and typical/expected
code pattern.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-10-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Use dev_err_probe() to avoid dmesg flood on actual defer.  This makes
the code also simpler.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-9-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.

Unlike in other typical of_node_get+syscon_node_to_regmap cases, the
reference cannot be dropped immediately after syscon_node_to_regmap(),
because further part of probe() uses it.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-8-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Replace a comma between expression statements by a semicolon.

Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240710031626.2003110-1-nichen@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Pull phy updates from Vinod Koul:
 "New Support
   - Samsung Exynos gs101 drd combo phy
   - Qualcomm SC8180x USB uniphy, IPQ9574 QMP PCIe phy
   - Airoha EN7581 PCIe phy
   - Freescale i.MX8Q HSIO SerDes phy
   - Starfive jh7110 dphy tx

  Updates:
   - Resume support for j721e-wiz driver
   - Updates to Exynos usbdrd driver
   - Support for optional power domains in g12a usb2-phy driver
   - Debugfs support and updates to zynqmp driver"

* tag 'phy-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (56 commits)
  phy: airoha: Add dtime and Rx AEQ IO registers
  dt-bindings: phy: airoha: Add dtime and Rx AEQ IO registers
  dt-bindings: phy: rockchip-emmc-phy: Convert to dtschema
  dt-bindings: phy: qcom,qmp-usb: fix spelling error
  phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)
  phy: exynos5-usbdrd: convert Vbus supplies to regulator_bulk
  phy: exynos5-usbdrd: convert (phy) register access clock to clk_bulk
  phy: exynos5-usbdrd: convert core clocks to clk_bulk
  phy: exynos5-usbdrd: support isolating HS and SS ports independently
  dt-bindings: phy: samsung,usb3-drd-phy: add gs101 compatible
  phy: core: Fix documentation of of_phy_get
  phy: starfive: Correct the dphy configure process
  phy: zynqmp: Add debugfs support
  phy: zynqmp: Take the phy mutex in xlate
  phy: zynqmp: Only wait for PLL lock "primary" instances
  phy: zynqmp: Store instance instead of type
  phy: zynqmp: Enable reference clock correctly
  phy: cadence-torrent: Check return value on register read
  phy: Fix the cacography in phy-exynos5250-usb2.c
  phy: phy-rockchip-samsung-hdptx: Select CONFIG_MFD_SYSCON
  ...

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/60089a71-dad2-4a87-a304-a738e3334d4a@siemens.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>