linux-stable.git/drivers/phy/st, branch v5.16.2

phy: stm32: fix st,slow-hs-slew-rate with st,decrease-hs-slew-rate

2021-11-16T09:58:51+00:00

st,decrease-hs-slew-rate is described in phy-stm32-usbphyc.yaml. Then
fix the property name in driver.

Fixes: 2f5e9f815a2f ("phy: stm32: add phy tuning support")
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211026154817.198937-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: add phy tuning support

2021-10-26T11:06:22+00:00

It can be necessary to adjust the phys settings to compensate parasitics.
This patch adds support of new optional properties to configure the tune
interface of the phys of stm32-usbphyc.
Properties are optional, that's why each property is skipped if not
found (-EINVAL).
Phy tuning is restored on resume because if deep low power state is
achieved, phy tuning configuration is reset.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211015161427.220784-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: restore utmi switch on resume

2021-10-26T11:06:22+00:00

UTMI switch value can be lost during suspend/resume, depending on the power
state reached.
This patch adds resume function to usbphyc, to reconfigure utmi switch
after suspend.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211015161427.220784-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy/drivers/stm32: use HZ macros

2021-09-08T18:50:26+00:00

HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.

Link: https://lkml.kernel.org/r/20210816114732.1834145-11-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano 
Reviewed-by: Andy Shevchenko 
Cc: Chanwoo Choi 
Cc: Christian Eggers 
Cc: Guenter Roeck 
Cc: Jonathan Cameron 
Cc: Jonathan Cameron 
Cc: Kyungmin Park 
Cc: Lars-Peter Clausen 
Cc: Lukasz Luba 
Cc: Maxime Coquelin 
Cc: Miquel Raynal 
Cc: MyungJoo Ham 
Cc: Peter Meerwald 
Cc: "Rafael J. Wysocki" 
Cc: Zhang Rui 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

phy: stm32: manage optional vbus regulator on phy_power_on/off

2021-05-31T08:38:58+00:00

This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210517120821.26466-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: register usbphyc as clock provider of ck_usbo_48m clock

2021-03-15T09:55:29+00:00

ck_usbo_48m is generated by usbphyc PLL and used by OTG controller
for Full-Speed use cases with dedicated Full-Speed transceiver.

ck_usbo_48m is available as soon as the PLL is enabled.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210208114659.15269-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: rework PLL Lock detection

2021-01-13T15:10:21+00:00

USBPHYC has a register per phy to control and monitor the debug interface
of the HS PHY through a digital debug access.
With this register, it is possible to know if PLL Lock input to phy is
high. That means the PLL is ready for HS operation.
Instead of using an hard-coded delay after PLL enable and PLL disable, use
this bit to ensure good operating of the HS PHY.
Also use an atomic counter (n_pll_cons) to count the actual number of PLL
consumers and get rid of stm32_usbphyc_has_one_phy_active.
The boolean active in the usbphyc_phy structure is kept, because we need to
know in remove if a phy_exit is required to properly disable the PLL.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210105090525.23164-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: ensure phy are no more active when removing the driver

2021-01-13T15:10:21+00:00

To ensure a good balancing of regulators, and allow PLL disabling when the
driver is removed, call stm32_usbphyc_phy_exit on each ports to set phys
inactive and disable PLL.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210105090525.23164-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: ensure pll is disabled before phys creation

2021-01-13T15:10:21+00:00

To ensure a good balancing of regulators, force PLL disable either by
reset or by clearing the PLLEN bit.
If waiting the powerdown pulse delay isn't enough, return -EPROBE_DEFER
instead of polling the PLLEN bit, which will be low at the next probe.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210105090525.23164-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul

phy: stm32: replace regulator_bulk* by multiple regulator_*

2021-01-13T15:10:21+00:00

Due to async_schedule_domain call in regulator_bulk_enable,
scheduling while atomic bug can raise if regulator_bulk_enable is called
under atomic context.
To avoid this issue, this patch replaces all regulator_bulk* by regulator_
per regulators.

Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20210105090525.23164-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul