linux-stable.git/drivers/pci, branch v4.9.296

PCI/MSI: Clear PCI_MSIX_FLAGS_MASKALL on error

2021-12-22T08:05:14+00:00

commit 94185adbfad56815c2c8401e16d81bdb74a79201 upstream.

PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.

That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:

        Capabilities: [b0] MSI-X: Enable- Count=67 Masked+

Clear the bit in the error path to restore the reset state.

Fixes: 438553958ba1 ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese 
Signed-off-by: Thomas Gleixner 
Tested-by: Stefan Roese 
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas 
Cc: Michal Simek 
Cc: Marek Vasut 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Signed-off-by: Greg Kroah-Hartman

PCI/MSI: Destroy sysfs before freeing entries

2021-11-26T10:48:40+00:00

commit 3735459037114d31e5acd9894fad9aed104231a0 upstream.

free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.

Move the sysfs release ahead of freeing the entries.

Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner 
Reviewed-by: Greg Kroah-Hartman 
Cc: Bjorn Helgaas 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
Signed-off-by: Greg Kroah-Hartman

PCI: aardvark: Don't spam about PIO Response Status

2021-11-26T10:48:38+00:00

[ Upstream commit 464de7e7fff767e87429cd7be09c4f2cb50a6ccb ]

Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().

For example CRS is not an error status, it just says that the request
should be retried.

Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún 
Signed-off-by: Lorenzo Pieralisi 
Signed-off-by: Sasha Levin

PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG

2021-11-26T10:48:25+00:00

commit 95997723b6402cd6c53e0f9e7ac640ec64eaaff8 upstream.

The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.

Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár 
Signed-off-by: Marek Behún 
Signed-off-by: Lorenzo Pieralisi 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman

PCI: Mark Atheros QCA6174 to avoid bus reset

2021-11-26T10:48:23+00:00

commit e3f4bd3462f6f796594ecc0dda7144ed2d1e5a26 upstream.

When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.

Add a quirk to avoid bus resets on this device, which avoids the hang.

[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein 
Signed-off-by: Bjorn Helgaas 
Reviewed-by: Pali Rohár 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman

PCI: Use pci_update_current_state() in pci_enable_device_flags()

2021-09-22T09:43:04+00:00

[ Upstream commit 14858dcc3b3587f4bb5c48e130ee7d68fc2b0a29 ]

Updating the current_state field of struct pci_dev the way it is done
in pci_enable_device_flags() before calling do_pci_enable_device() may
not work.  For example, if the given PCI device depends on an ACPI
power resource whose _STA method initially returns 0 ("off"), but the
config space of the PCI device is accessible and the power state
retrieved from the PCI_PM_CTRL register is D0, the current_state
field in the struct pci_dev representing that device will get out of
sync with the power.state of its ACPI companion object and that will
lead to power management issues going forward.

To avoid such issues, make pci_enable_device_flags() call
pci_update_current_state() which takes ACPI device power management
into account, if present, to retrieve the current power state of the
device.

Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz 
Signed-off-by: Rafael J. Wysocki 
Tested-by: Maximilian Luz 
Signed-off-by: Sasha Levin

PCI: Return ~0 data on pciconfig_read() CAP_SYS_ADMIN failure

2021-09-22T09:43:04+00:00

commit a8bd29bd49c4156ea0ec5a97812333e2aeef44e7 upstream.

The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.

If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.

When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno.  But after
e4585da22ad0 ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.

Userspace may rely on the ~0 data to detect errors, but after e4585da22ad0,
that would not detect CAP_SYS_ADMIN errors.

Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.

[bhelgaas: commit log, fold in Nathan's fix
https://lore.kernel.org/r/20210803200836.500658-1-nathan@kernel.org]
Fixes: e4585da22ad0 ("pci syscall.c: Switch to refcounting API")
Link: https://lore.kernel.org/r/20210729233755.1509616-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński 
Signed-off-by: Bjorn Helgaas 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman

PCI: Restrict ASMedia ASM1062 SATA Max Payload Size Supported

2021-09-22T09:43:03+00:00

commit b12d93e9958e028856cbcb061b6e64728ca07755 upstream.

The ASMedia ASM1062 SATA controller advertises Max_Payload_Size_Supported
of 512, but in fact it cannot handle incoming TLPs with payload size of
512.

We discovered this issue on PCIe controllers capable of MPS = 512 (Aardvark
and DesignWare), where the issue presents itself as an External Abort.
Bjorn Helgaas says:

  Probably ASM1062 reports a Malformed TLP error when it receives a data
  payload of 512 bytes, and Aardvark, DesignWare, etc convert this to an
  arm64 External Abort. [1]

To avoid this problem, limit the ASM1062 Max Payload Size Supported to 256
bytes, so we set the Max Payload Size of devices that may send TLPs to the
ASM1062 to 256 or less.

[1] https://lore.kernel.org/linux-pci/20210601170907.GA1949035@bjorn-Precision-5520/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212695
Link: https://lore.kernel.org/r/20210624171418.27194-2-kabel@kernel.org
Reported-by: Rötti 
Signed-off-by: Marek Behún 
Signed-off-by: Bjorn Helgaas 
Reviewed-by: Krzysztof Wilczyński 
Reviewed-by: Pali Rohár 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman

PCI/MSI: Skip masking MSI-X on Xen PV

2021-09-22T09:43:03+00:00

commit 1a519dc7a73c977547d8b5108d98c6e769c89f4b upstream.

When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:

    BUG: unable to handle page fault for address: ffffc9004069100c
    #PF: supervisor write access in kernel mode
    #PF: error_code(0x0003) - permissions violation
    RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
     e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
     e1000_probe+0x41f/0xdb0 [e1000e]
     local_pci_probe+0x42/0x80
    (...)

The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.

Add the check to make this function XEN PV compatible.

Fixes: 7d5ec3d36123 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki 
Signed-off-by: Thomas Gleixner 
Acked-by: Bjorn Helgaas 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Signed-off-by: Greg Kroah-Hartman

PCI: PM: Enable PME if it can be signaled from D3cold

2021-09-22T09:43:00+00:00

[ Upstream commit 0e00392a895c95c6d12d42158236c8862a2f43f2 ]

PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().

[Note that if the device does not end up in D3cold and it cannot
 signal PME from the original target power state, it will not signal
 PME, so in that case the behavior does not change.]

Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e815 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg 
Reported-by: Utkarsh H Patel 
Reported-by: Koba Ko 
Signed-off-by: Rafael J. Wysocki 
Reviewed-by: Mika Westerberg 
Tested-by: Mika Westerberg 
Signed-off-by: Sasha Levin