Pull libata fixes from Tejun Heo:
 "I sat on them too long and it's quite a few this late, but nothing has
  a wide blast area. The changes are...

   - Fix corner cases in SG command handling.

   - Recent introduction of default powersaving mode config option
     exposed several devices with broken powersaving behaviors. A number
     of patches to update the blacklist accordingly.

   - Fix a kernel panic on SAS hotplug.

   - Other misc and device specific updates"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
  libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
  libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
  libata: Enable queued TRIM for Samsung SSD 860
  PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
  ahci: Add PCI-id for the Highpoint Rocketraid 644L card
  ata: do not schedule hot plug if it is a sas host
  libata: disable LPM for Crucial BX100 SSD 500GB drive
  libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
  libata: update documentation for sysfs interfaces
  ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
  libata: transport: cleanup documentation of sysfs interface
  sata_rcar: Reset SATA PHY when Salvator-X board resumes
  libata: don't try to pass through NCQ commands to non-NCQ devices
  libata: remove WARN() for DMA or PIO command without data
  libata: fix length validation of ATAPI-relayed SCSI commands
  ata: libahci: fix comment indentation
  ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
  libata: Fix compile warning with ATA_DEBUG enabled

Pull PCI fixes from Bjorn Helgaas:

 - fix sparc build issue when OF_IRQ not enabled (Guenter Roeck)

 - fix enumeration of devices below switches on DesignWare-based
   controllers (Koen Vandeputte)

* tag 'pci-v4.16-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: dwc: Fix enumeration end when reaching root subordinate
  PCI: Move of_irq_parse_and_map_pci() declaration under OF_IRQ

The subordinate value indicates the highest bus number which can be
reached downstream though a certain device.

Commit a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent") ensures that downstream devices cannot assign busnumbers higher
than the upstream device subordinate number, which was indeed illogical.

By default, dw_pcie_setup_rc() inits the Root Complex subordinate to a
value of 0x01.

Due to this combined with above commit, enumeration stops digging deeper
downstream as soon as bus num 0x01 has been assigned, which is always the
case for a bridge device.

This results in all devices behind a bridge bus remaining undetected, as
these would be connected to bus 0x02 or higher.

Fix this by initializing the RC to a subordinate value of 0xff, which is
not altering hardware behaviour in any way, but informs probing function
pci_scan_bridge() later on which reads this value back from register.

The following nasty errors during boot are also fixed by this:

  pci_bus 0000:02: busn_res: can not insert [bus 02-ff] under [bus 01] (conflicts with (null) [bus 01])
  ...
  pci_bus 0000:03: [bus 03] partially hidden behind bridge 0000:01 [bus 01]
  ...
  pci_bus 0000:04: [bus 04] partially hidden behind bridge 0000:01 [bus 01]
  ...
  pci_bus 0000:05: [bus 05] partially hidden behind bridge 0000:01 [bus 01]
  pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
  pci_bus 0000:02: busn_res: can not insert [bus 02-05] under [bus 01] (conflicts with (null) [bus 01])
  pci_bus 0000:02: [bus 02-05] partially hidden behind bridge 0000:01 [bus 01]

Fixes: a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent")
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org	# v4.15+
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>

The Highpoint RocketRAID 644L uses a Marvel 88SE9235 controller, as with
other Marvel controllers this needs a function 1 DMA alias quirk.

Note the RocketRAID 642L uses the same Marvel 88SE9235 controller and
already is listed with a function 1 DMA alias quirk.

Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Pull PCI fixes from Bjorn Helgaas:

 - Update pci.ids location (documentation only) (Randy Dunlap)

 - Fix a crash when BIOS didn't assign a BAR and we try to enlarge it
   (Christian König)

* tag 'pci-v4.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Allow release of resources that were never assigned
  PCI: Update location of pci.ids file

It is entirely possible that the BIOS wasn't able to assign resources to a
device. In this case don't crash in pci_release_resource() when we try to
resize the resource.

Fixes: 8bb705e3e79d ("PCI: Add pci_resize_resource() for resizing BARs")
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
CC: stable@vger.kernel.org	# v4.15+

We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help.  The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.

The right idea is to follow the kernel.org
commit 1c7de2b4ff88 ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.

The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor.  Thus PF4 can
be exported to a Virtual Machine and everything should work.

Fixes: 67e658794ca1 ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org>  # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.

Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups, a few new quirks, a couple of
  updates related to the handling of ACPI tables and ACPICA copyrights
  refreshment.

  Specifics:

   - Update the ACPICA kernel code to upstream revision 20180105
     including:
       * Assorted fixes (Jung-uk Kim)
       * Support for X32 ABI compilation (Anuj Mittal)
       * Update of ACPICA copyrights to 2018 (Bob Moore)

   - Prepare for future modifications to avoid executing the _STA
     control method too early (Hans de Goede)

   - Make the processor performance control library code ignore _PPC
     notifications if they cannot be handled and fix up the C1 idle
     state definition when it is used as a fallback state (Chen Yu,
     Yazen Ghannam)

   - Make it possible to use the SPCR table on x86 and to replace the
     original IORT table with a new one from initrd (Prarit Bhargava,
     Shunyong Yang)

   - Add battery-related quirks for Asus UX360UA and UX410UAK and add
     quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
     Heng Feng)

   - Address static checker warnings in the CPPC code (Gustavo Silva)

   - Avoid printing a raw pointer to the kernel log in the smart battery
     driver (Greg Kroah-Hartman)"

* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: sbshc: remove raw pointer from printk() message
  ACPI: SPCR: Make SPCR available to x86
  ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
  ACPI / tables: Add IORT to injectable table list
  ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
  ACPICA: Update version to 20180105
  ACPICA: All acpica: Update copyrights to 2018
  ACPI / processor: Set default C1 idle state description
  ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
  ACPI: processor_perflib: Do not send _PPC change notification if not ready
  ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
  ACPI / bus: Do not call _STA on battery devices with unmet dependencies
  PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
  ACPI: export acpi_bus_get_status_handle()
  ACPICA: Add a missing pair of parentheses
  ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
  ACPICA: Avoid NULL pointer arithmetic
  ACPICA: Linux: add support for X32 ABI compilation
  ACPI / video: Use true for boolean value

Pull PCI updates from Bjorn Helgaas:

 - skip AER driver error recovery callbacks for correctable errors
   reported via ACPI APEI, as we already do for errors reported via the
   native path (Tyler Baicar)

 - fix DPC shared interrupt handling (Alex Williamson)

 - print full DPC interrupt number (Keith Busch)

 - enable DPC only if AER is available (Keith Busch)

 - simplify DPC code (Bjorn Helgaas)

 - calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
   Helgaas)

 - enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
   Helgaas)

 - move ASPM internal interfaces out of public header (Bjorn Helgaas)

 - allow hot-removal of VGA devices (Mika Westerberg)

 - speed up unplug and shutdown by assuming Thunderbolt controllers
   don't support Command Completed events (Lukas Wunner)

 - add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
   Jay Cornwall)

 - expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)

 - clean up PCI DMA interface usage (Christoph Hellwig)

 - remove PCI pool API (replaced with DMA pool) (Romain Perier)

 - deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
   Kaya)

 - move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)

 - add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)

 - remove warnings on sysfs mmap failure (Bjorn Helgaas)

 - quiet ROM validation messages (Alex Deucher)

 - remove redundant memory alloc failure messages (Markus Elfring)

 - fill in types for compile-time VGA and other I/O port resources
   (Bjorn Helgaas)

 - make "pci=pcie_scan_all" work for Root Ports as well as Downstream
   Ports to help AmigaOne X1000 (Bjorn Helgaas)

 - add SPDX tags to all PCI files (Bjorn Helgaas)

 - quirk Marvell 9128 DMA aliases (Alex Williamson)

 - quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)

 - fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
   Cassel)

 - use DMA API to get MSI address for DesignWare IP (Niklas Cassel)

 - fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)

 - fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)

 - add support for ARTPEC-7 SoC (Niklas Cassel)

 - add endpoint-mode support for ARTPEC (Niklas Cassel)

 - add Cadence PCIe host and endpoint controller driver (Cyrille
   Pitchen)

 - handle multiple INTx status bits being set in dra7xx (Vignesh R)

 - translate dra7xx hwirq range to fix INTD handling (Vignesh R)

 - remove deprecated Exynos PHY initialization code (Jaehoon Chung)

 - fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)

 - fix NULL pointer dereference in iProc BCMA driver (Ray Jui)

 - fix Keystone interrupt-controller-node lookup (Johan Hovold)

 - constify qcom driver structures (Julia Lawall)

 - rework Tegra config space mapping to increase space available for
   endpoints (Vidya Sagar)

 - simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)

 - remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)

 - add support for Global Fabric Manager Server (GFMS) event to
   Microsemi Switchtec switch driver (Logan Gunthorpe)

 - add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)

* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
  PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
  dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
  PCI: endpoint: Fix EPF device name to support multi-function devices
  PCI: endpoint: Add the function number as argument to EPC ops
  PCI: cadence: Add host driver for Cadence PCIe controller
  dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
  PCI: Add vendor ID for Cadence
  PCI: Add generic function to probe PCI host controllers
  PCI: generic: fix missing call of pci_free_resource_list()
  PCI: OF: Add generic function to parse and allocate PCI resources
  PCI: Regroup all PCI related entries into drivers/pci/Makefile
  PCI/DPC: Reformat DPC register definitions
  PCI/DPC: Add and use DPC Status register field definitions
  PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
  PCI/DPC: Remove unnecessary RP PIO register structs
  PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
  PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
  PCI/DPC: Make RP PIO log size check more generic
  PCI/DPC: Rename local "status" to "dpc_status"
  PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
  ...