Paul reported that after f75b99d5a77d ("PCI: Enforce bus address limits in
resource allocation") on a 32-bit kernel (CONFIG_PHYS_ADDR_T_64BIT not
set), intel-gtt complained "can't ioremap flush page - no chipset
flushing".  In addition, other PCI resource allocations, e.g., for bridge
windows, failed.

This happens because we incorrectly skip bus resources of
[mem 0x00000000-0xffffffff] because we think they are of size zero.
When resource_size_t is 32 bits wide, resource_size() on
[mem 0x00000000-0xffffffff] returns 0 because (r->end - r->start + 1)
overflows.

Therefore, we can't use "resource_size() == 0" to decide that allocation
from this resource will fail.  allocate_resource() should fail anyway if it
can't satisfy the address constraints, so we should just depend on that.

A [mem 0x00000000-0xffffffff] bus resource is obviously not really valid,
but we do fall back to it as a default when we don't have information about
host bridge apertures.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=71611
Fixes: f75b99d5a77d PCI: Enforce bus address limits in resource allocation
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Andreas reported that after 1f42db786b14 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.

This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.

Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device().  But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.

This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.

Fixes: 1f42db786b14 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Pull PCI updates from Bjorn Helgaas:
 "The most interesting thing here is the change to enable INTx (by
  clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
  Apparently the Baytrail BIOS does this, which means EHCI doesn't work.

  Also, fix an AHCI MSI regression and other issues with the recent MSI
  changes.  This also adds pci_enable_msi_exact() and
  pci_enable_msix_exact(), which aren't regression fixes, but will keep
  us from touching drivers twice (once to stop using the deprecated
  pci_enable_msi(), etc., and again to use the *_exact() variants).

  There's also a minor MVEBU fix.

  Summary:

  MSI:
    - Fix AHCI single-MSI fallback (Alexander Gordeev)
    - Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
    - Fix htmldocs problem (Masanari Iida)
    - Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
    - Update documentation (Alexander Gordeev)

  Miscellaneous:
    - mvebu: expose device ID & revision via lspci (Andrew Lunn)
    - Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"

* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ahci: Fix broken fallback to single MSI mode
  PCI: Enable INTx if BIOS left them disabled
  PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
  PCI/MSI: Fix cut-and-paste errors in documentation
  PCI/MSI: Add pci_enable_msi() documentation back
  PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
  PCI/MSI: Fix leak of msi_attrs
  PCI/MSI: Check kmalloc() return value, fix leak of name
  PCI: mvebu: Use Device ID and revision from underlying endpoint

Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts.  Clear Interrupt Disable so we get those interrupts.

Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.

Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>

An empty line in msi.c caused "make htmldocs" failure:

  Warning(/home/iida/Repo/linux-next//drivers/pci/msi.c:962): bad line:

Fixes: ff1aa430a2fa ("PCI/MSI: Add pci_msix_vec_count()")
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Coverity reported that I forgot to clean up some allocated memory on the
error path in populate_msi_sysfs(), so this patch fixes that.

Thanks to Dave Jones for pointing out where the error was, I obviously
can't read code this morning...

Found by Coverity (CID 1163317).

Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dave Jones <davej@redhat.com>

Coverity reported that I forgot to check the return value of kmalloc() when
creating the MSI attribute name, so fix that up and properly free it if
there is an error when allocating the msi_dev_attr variable.

Found by Coverity (CID 1163315 and 1163316).

Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Marvell SoCs place the SoC number into the PCIe endpoint device ID.  The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.

The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.

When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality.  Debian would
like to use this in order to aid installing the correct DTB file.

Fixes: 45361a4fe4464 ("pci: PCIe driver for Marvell Armada 370/XP systems")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org	# v3.11+

The ACPI specification (ACPI 5.0A, Section 6.3.7) says:

 _STA may return bit 0 clear (not present) with bit 3 set (device is
 functional). This case is used to indicate a valid device for which
 no device driver should be loaded (for example, a bridge device.)
 Children of this device may be present and valid. OSPM should
 continue enumeration below a device whose _STA returns this bit
 combination.

Evidently, some BIOSes follow that and return 0x0A from _STA, which
causes problems to happen when they trigger bus check or device check
notifications for those devices too.  Namely, ACPIPHP thinks that they
are gone and may drop them, for example, if such a notification is
triggered during a resume from system suspend.

To fix that, modify ACPICA to regard devies as present and
functioning if _STA returns both the ACPI_STA_DEVICE_ENABLED
and ACPI_STA_DEVICE_FUNCTIONING bits set for them.

Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Subject and changelog, minor code modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If a PCI bridge with an ACPIPHP context attached is removed via
sysfs, the code path executed as a result is the following:

pci_stop_and_remove_bus_device_locked
 pci_remove_bus
  pcibios_remove_bus
   acpi_pci_remove_bus
    acpiphp_remove_slots
     cleanup_bridge
      unregister_hotplug_dock_device (drops dock references to the bridge)
     put_bridge
      free_bridge
       acpiphp_put_context (for each child, under context lock)
        kfree (context)

Now, if a dock event affecting one of the bridge's child devices
occurs (roughly at the same time), it will lead to the following code
path:

acpi_dock_deferred_cb
 dock_notify
  handle_eject_request
   hot_remove_dock_devices
    dock_hotplug_event
     hotplug_event (dereferences context)

That may lead to a kernel crash in hotplug_event() if it is executed
after the last kfree() in the bridge removal code path.

To prevent that from happening, add a wrapper around hotplug_event()
called dock_event() and point the .handler pointer in acpiphp_dock_ops
to it.  Make that wrapper retrieve the device's ACPIPHP context using
acpiphp_get_context() (instead of taking it from the data argument)
under acpiphp_context_lock and check if the parent bridge's
is_going_away flag is set.  If that flag is set, it will return
immediately and if it is not set it will grab a reference to the
device's parent bridge before executing hotplug_event().

Then, in the above scenario, the reference to the parent bridge
held by dock_event() will prevent free_bridge() from being executed
for it until hotplug_event() returns.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>