linux-stable.git/drivers/pci/probe.c, branch v3.2

PCI: Clean-up MPS debug output

2011-10-27T19:45:44+00:00

Clean-up MPS debug output to make it a single line and aligned, thus
making it more readable for a large number of buses and devices in a
single system.

Suggested by Benjamin Herrenschmidt 

Signed-off-by: Jon Mason 
Signed-off-by: Jesse Barnes

PCI: enable MPS "performance" setting to properly handle bridge MPS

2011-10-27T19:45:43+00:00

Rework the "performance" MPS option to configure the device MPS with the
smaller of the device MPSS or the bridge MPS (which is assumed to be
properly configured at this point to the largest allowable MPS based on
its parent bus).

Also, rework the MRRS setting to report an inability to set the MRRS to
a valid setting.

Signed-off-by: Jon Mason 
Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Jesse Barnes

PCI: Disable MPS configuration by default

2011-10-04T16:52:28+00:00

Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).

Signed-off-by: Jon Mason 
Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Linus Torvalds

pci: Don't crash when reading mpss from root complex

2011-09-13T23:08:31+00:00

In pcie_find_smpss(), we have the following statement:

 	if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) ||
	    dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT))

The problem is that at least on my machine, this gets called for the
root complex (virtual P2P bridge), and dev->bus->self is NULL since
the parent bus for this is not itself anchor to a PCI device.

This adds the necessary NULL check.

Signed-off-by: Benjamin Herrenschmidt 
Acked-by: Jon Mason 
Signed-off-by: Linus Torvalds

PCI: Remove MRRS modification from MPS setting code

2011-09-10T02:49:58+00:00

Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices.  Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode.  Also, make pcie_bus_safe
the default procedure.

Tested-by: Sven Schnelle 
Tested-by: Simon Kirby 
Tested-by: Stephen M. Cameron 
Reported-and-tested-by: Eric Dumazet 
Reported-and-tested-by: Niels Ole Salscheider 
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason 
Acked-by: Jesse Barnes 
Signed-off-by: Linus Torvalds

Fix pointer dereference before call to pcie_bus_configure_settings

2011-09-10T02:49:58+00:00

Commit b03e7495a862 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.

To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.

Reported-by: Stanislaw Gruszka 
Signed-off-by: Shyam Iyer 
Signed-off-by: Jon Mason 
Acked-by: Jesse Barnes 
Signed-off-by: Linus Torvalds

PCI: export pcie_bus_configure_settings symbol

2011-08-02T15:53:00+00:00

pcie_bus_configure_settings needs to be exported if the PCI hotplug
driver is being compiled as a module.

Reported-by: Stephen Rothwell 
Signed-off-by: Jon Mason 
Signed-off-by: Jesse Barnes

PCI: Set PCI-E Max Payload Size on fabric

2011-08-01T18:49:16+00:00

On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size.  There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device.  However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.

This can be achieved two ways:

- A conservative approach is to use the smallest common denominator of
  the entire tree below a root complex for every device on that fabric.

This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.

It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.

- A more optimal way is possible, if it falls within a couple of
  constraints:
* The top-level host bridge will never generate packets larger than the
  smallest TLP (or if it can be controlled independently from its MPS at
  least)
* The device will never generate packets larger than MPS (which can be
  configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
  some additional code to specifically deal with that case

Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.

In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.

To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls.  "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.

NOTE: due to the location of the enablement, each arch will need to add
calls to this function.  This patch only enables x86.

This patch includes a number of changes recommended by Benjamin
Herrenschmidt.

Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason 
Signed-off-by: Jesse Barnes

Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6

2011-07-30T06:35:05+00:00

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: remove printks about disabled bridge windows
  PCI: fold pci_calc_resource_flags() into decode_bar()
  PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
  PCI: correct pcie_set_readrq write size
  PCI: pciehp: change wait time for valid configuration access
  x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
  PCI: ARI is a PCIe v2 feature
  x86/PCI: quirks: Use pci_dev->revision
  PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
  PCI hotplug: cpqphp: use pci_dev->vendor
  PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
  x86/PCI: config space accessor functions should not ignore the segment argument
  PCI: Assign values to 'pci_obff_signal_type' enumeration constants
  x86/PCI: reduce severity of host bridge window conflict warnings
  PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
  PCI: PCIe AER: add aer_recover_queue
  x86/PCI: select direct access mode for mmconfig option
  PCI hotplug: Rename is_ejectable which also exists in dock.c

Merge branch 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

2011-07-22T21:54:02+00:00

* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  pci/of: Consolidate pci_bus_to_OF_node()
  pci/of: Consolidate pci_device_to_OF_node()
  x86/devicetree: Use generic PCI <-> OF matching
  microblaze/pci: Move the remains of pci_32.c to pci-common.c
  microblaze/pci: Remove powermac originated cruft
  pci/of: Match PCI devices to OF nodes dynamically