linux-stable.git/drivers/pci/hotplug, branch v5.17.2

PCI: pciehp: Clear cmd_busy bit in polling mode

2022-04-08T11:57:31+00:00

commit 92912b175178c7e895f5e5e9f1e30ac30319162b upstream.

Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands."  If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.

pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control.  If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().

But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:

  pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
  pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)

Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).

[bhelgaas: commit log]
Fixes: a5dd4b4b0570 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang 
Signed-off-by: Bjorn Helgaas 
Reviewed-by: Lukas Wunner 
Cc: stable@vger.kernel.org	# v4.19+
Signed-off-by: Greg Kroah-Hartman

Merge branch 'pci/errors'

2022-01-13T15:57:52+00:00

- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking
  for transaction errors on PCI (Naveen Naidu)

- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead
  of in host controller drivers, when transactions fail on PCI (Naveen
  Naidu)

- Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads
  (Naveen Naidu)

* pci/errors:
  PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors
  PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors
  PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors
  PCI: Use PCI_ERROR_RESPONSE to identify config read errors
  PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
  PCI: rockchip-host: Drop error data fabrication when config read fails
  PCI: rcar-host: Drop error data fabrication when config read fails
  PCI: altera: Drop error data fabrication when config read fails
  PCI: mvebu: Drop error data fabrication when config read fails
  PCI: aardvark: Drop error data fabrication when config read fails
  PCI: kirin: Drop error data fabrication when config read fails
  PCI: histb: Drop error data fabrication when config read fails
  PCI: exynos: Drop error data fabrication when config read fails
  PCI: mediatek: Drop error data fabrication when config read fails
  PCI: iproc: Drop error data fabrication when config read fails
  PCI: thunder: Drop error data fabrication when config read fails
  PCI: Drop error data fabrication when config read fails
  PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices
  PCI: Set error response data when config read fails
  PCI: Add PCI_ERROR_RESPONSE and related definitions

PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors

2022-01-12T12:42:51+00:00

Use down_read_nested() and down_write_nested() when taking the
ctrl->reset_lock rw-sem, passing the number of PCIe hotplug controllers in
the path to the PCI root bus as lock subclass parameter.

This fixes the following false-positive lockdep report when unplugging a
Lenovo X1C8 from a Lenovo 2nd gen TB3 dock:

  pcieport 0000:06:01.0: pciehp: Slot(1): Link Down
  pcieport 0000:06:01.0: pciehp: Slot(1): Card not present
  ============================================
  WARNING: possible recursive locking detected
  5.16.0-rc2+ #621 Not tainted
  --------------------------------------------
  irq/124-pciehp/86 is trying to acquire lock:
  ffff8e5ac4299ef8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_check_presence+0x23/0x80

  but task is already holding lock:
  ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180

   other info that might help us debug this:
   Possible unsafe locking scenario:

	 CPU0
	 ----
    lock(&ctrl->reset_lock);
    lock(&ctrl->reset_lock);

   *** DEADLOCK ***

   May be due to missing lock nesting notation

  3 locks held by irq/124-pciehp/86:
   #0: ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
   #1: ffffffffa3b024e8 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pciehp_unconfigure_device+0x31/0x110
   #2: ffff8e5ac1ee2248 (&dev->mutex){....}-{3:3}, at: device_release_driver+0x1c/0x40

  stack backtrace:
  CPU: 4 PID: 86 Comm: irq/124-pciehp Not tainted 5.16.0-rc2+ #621
  Hardware name: LENOVO 20U90SIT19/20U90SIT19, BIOS N2WET30W (1.20 ) 08/26/2021
  Call Trace:
   
   dump_stack_lvl+0x59/0x73
   __lock_acquire.cold+0xc5/0x2c6
   lock_acquire+0xb5/0x2b0
   down_read+0x3e/0x50
   pciehp_check_presence+0x23/0x80
   pciehp_runtime_resume+0x5c/0xa0
   device_for_each_child+0x45/0x70
   pcie_port_device_runtime_resume+0x20/0x30
   pci_pm_runtime_resume+0xa7/0xc0
   __rpm_callback+0x41/0x110
   rpm_callback+0x59/0x70
   rpm_resume+0x512/0x7b0
   __pm_runtime_resume+0x4a/0x90
   __device_release_driver+0x28/0x240
   device_release_driver+0x26/0x40
   pci_stop_bus_device+0x68/0x90
   pci_stop_bus_device+0x2c/0x90
   pci_stop_and_remove_bus_device+0xe/0x20
   pciehp_unconfigure_device+0x6c/0x110
   pciehp_disable_slot+0x5b/0xe0
   pciehp_handle_presence_or_link_change+0xc3/0x2f0
   pciehp_ist+0x179/0x180

This lockdep warning is triggered because with Thunderbolt, hotplug ports
are nested. When removing multiple devices in a daisy-chain, each hotplug
port's reset_lock may be acquired recursively. It's never the same lock, so
the lockdep splat is a false positive.

Because locks at the same hierarchy level are never acquired recursively, a
per-level lockdep class is sufficient to fix the lockdep warning.

The choice to use one lockdep subclass per pcie-hotplug controller in the
path to the root-bus was made to conserve class keys because their number
is limited and the complexity grows quadratically with number of keys
according to Documentation/locking/lockdep-design.rst.

Link: https://lore.kernel.org/linux-pci/20190402021933.GA2966@mit.edu/
Link: https://lore.kernel.org/linux-pci/de684a28-9038-8fc6-27ca-3f6f2f6400d7@redhat.com/
Link: https://lore.kernel.org/r/20211217141709.379663-1-hdegoede@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208855
Reported-by: "Theodore Ts'o" 
Signed-off-by: Hans de Goede 
Signed-off-by: Bjorn Helgaas 
Reviewed-by: Lukas Wunner 
Cc: stable@vger.kernel.org

PCI: ibmphp: Remove commented-out functions

2021-12-10T15:55:47+00:00

The functions get_max_adapter_speed() and get_bus_name() in ibmphp_core.c
are commented-out and the fields .get_max_adapter_speed and
.get_bus_name_status are removed from struct hotplug_slot_ops in
pci_hotplug.h. Remove the commented-out functions.

Link: https://lore.kernel.org/r/20211209213618.20522-1-makvihas@gmail.com
Signed-off-by: Vihas Mak 
Signed-off-by: Bjorn Helgaas

PCI: pciehp: Fix infinite loop in IRQ handler upon power fault

2021-11-19T18:39:33+00:00

The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky:  It can only be cleared
after turning off slot power.  Per PCIe r5.0, sec. 6.7.1.8:

  If a power controller detects a main power fault on the hot-plug slot,
  it must automatically set its internal main power fault latch [...].
  The main power fault latch is cleared when software turns off power to
  the hot-plug slot.

The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfafe ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17f3 ("PCI: pciehp: enable
software notification on empty slots").

Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt
race"):  The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set.  That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop.  Fix by setting the
power_fault_detected flag already in the hardirq handler.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao 
Tested-by: Joseph Bao 
Signed-off-by: Lukas Wunner 
Signed-off-by: Bjorn Helgaas 
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes

PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads

2021-11-18T20:13:18+00:00

When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).

Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.

Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware.  This unifies PCI error response checking and makes error
checks consistent and easier to find.

Link: https://lore.kernel.org/r/b12005c0d57bb9d4c8b486724d078b7bd92f8321.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu 
Signed-off-by: Bjorn Helgaas

PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads

2021-11-18T20:13:18+00:00

When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).

Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.

Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware.  This unifies PCI error response checking and makes error
checks consistent and easier to find.

Compile tested only.

Link: https://lore.kernel.org/r/e185b052fbfd530df703a36dd31126cb870eed95.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu 
Signed-off-by: Bjorn Helgaas 
Acked-by: Lukas Wunner

s390/pci: implement reset_slot for hotplug slot

2021-11-08T13:17:49+00:00

This is done by adding a zpci_hot_reset_device() call which does a low
level reset of the PCI function without changing its higher level
function state. This way it can be used while the zPCI function is bound
to a driver and with DMA tables being controlled either through the
IOMMU or DMA APIs which is prohibited when using zpci_disable_device()
as that drop existing DMA translations.

As this reset, unlike a normal FLR, also calls zpci_clear_irq() we need
to implement arch_restore_msi_irqs() and make sure we re-enable IRQs for
the PCI function if they were previously disabled.

Reviewed-by: Pierre Morel 
Reviewed-by: Matthew Rosato 
Signed-off-by: Niklas Schnelle 
Signed-off-by: Vasily Gorbik

Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2021-11-06T21:36:12+00:00

Pull pci updates from Bjorn Helgaas:
 "Enumeration:
   - Conserve IRQs by setting up portdrv IRQs only when there are users
     (Jan Kiszka)
   - Rework and simplify _OSC negotiation for control of PCIe features
     (Joerg Roedel)
   - Remove struct pci_dev.driver pointer since it's redundant with the
     struct device.driver pointer (Uwe Kleine-König)

  Resource management:
   - Coalesce contiguous host bridge apertures from _CRS to accommodate
     BARs that cover more than one aperture (Kai-Heng Feng)

  Sysfs:
   - Check CAP_SYS_ADMIN before parsing user input (Krzysztof
     Wilczyński)
   - Return -EINVAL consistently from "store" functions (Krzysztof
     Wilczyński)
   - Use sysfs_emit() in endpoint "show" functions to avoid buffer
     overruns (Kunihiko Hayashi)

  PCIe native device hotplug:
   - Ignore Link Down/Up caused by resets during error recovery so
     endpoint drivers can remain bound to the device (Lukas Wunner)

  Virtualization:
   - Avoid bus resets on Atheros QCA6174, where they hang the device
     (Ingmar Klein)
   - Work around Pericom PI7C9X2G switch packet drop erratum by using
     store and forward mode instead of cut-through (Nathan Rossi)
   - Avoid trying to enable AtomicOps on VFs; the PF setting applies to
     all VFs (Selvin Xavier)

  MSI:
   - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
     interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
     Song)

  VPD:
   - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
     in the possible VPD space; use these to simplify the cxgb3 driver
     (Heiner Kallweit)

  Peer-to-peer DMA:
   - Add (not subtract) the bus offset when calculating DMA address
     (Wang Lu)

  ASPM:
   - Re-enable LTR at Downstream Ports so they don't report Unsupported
     Requests when reset or hot-added devices send LTR messages
     (Mingchuang Qiao)

  Apple PCIe controller driver:
   - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
     Zyngier)

  Cadence PCIe controller driver:
   - Return success when probe succeeds instead of falling into error
     path (Li Chen)

  HiSilicon Kirin PCIe controller driver:
   - Reorganize PHY logic and add support for external PHY drivers
     (Mauro Carvalho Chehab)
   - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
     Carvalho Chehab)
   - Add Kirin 970 support (Mauro Carvalho Chehab)
   - Make driver removable (Mauro Carvalho Chehab)

  Intel VMD host bridge driver:
   - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
     enabled (Adrian Huang)
   - Number each controller so we can tell them apart in
     /proc/interrupts (Chunguang Xu)
   - Avoid building on UML because VMD depends on x86 bare metal APIs
     (Johannes Berg)

  Marvell Aardvark PCIe controller driver:
   - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
   - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
   - Downgrade PIO Response Status messages to debug level (Marek Behún)
   - Preserve CRS SV (Config Request Retry Software Visibility) bit in
     emulated Root Control register (Pali Rohár)
   - Fix issue in configuring reference clock (Pali Rohár)
   - Don't clear status bits for masked interrupts (Pali Rohár)
   - Don't mask unused interrupts (Pali Rohár)
   - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
   - Retry config accesses on CRS response (Pali Rohár)
   - Simplify emulated Root Capabilities initialization (Pali Rohár)
   - Fix several link training issues (Pali Rohár)
   - Fix link-up checking via LTSSM (Pali Rohár)
   - Fix reporting of Data Link Layer Link Active (Pali Rohár)
   - Fix emulation of W1C bits (Marek Behún)
   - Fix MSI domain .alloc() method to return zero on success (Marek
     Behún)
   - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
     (Marek Behún)
   - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
     at startup; PCI core will set those as necessary (Pali Rohár)
   - When operating as a Root Port, set class code to "PCI Bridge"
     instead of the default "Mass Storage Controller" (Pali Rohár)
   - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
     implement this per spec (Pali Rohár)
   - Add emulation of option ROM BAR since aardvark doesn't implement
     this per spec (Pali Rohár)

  MediaTek MT7621 PCIe controller driver:
   - Add MediaTek MT7621 PCIe host controller driver and DT binding
     (Sergio Paracuellos)

  Qualcomm PCIe controller driver:
   - Add SC8180x compatible string (Bjorn Andersson)
   - Add endpoint controller driver and DT binding (Manivannan
     Sadhasivam)
   - Restructure to use of_device_get_match_data() (Prasad Malisetty)
   - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)

  Renesas R-Car PCIe controller driver:
   - Remove unnecessary includes (Geert Uytterhoeven)

  Rockchip DesignWare PCIe controller driver:
   - Add DT binding (Simon Xue)

  Socionext UniPhier Pro5 controller driver:
   - Serialize INTx masking/unmasking (Kunihiko Hayashi)

  Synopsys DesignWare PCIe controller driver:
   - Run dwc .host_init() method before registering MSI interrupt
     handler so we can deal with pending interrupts left by bootloader
     (Bjorn Andersson)
   - Clean up Kconfig dependencies (Andy Shevchenko)
   - Export symbols to allow more modular drivers (Luca Ceresoli)

  TI DRA7xx PCIe controller driver:
   - Allow host and endpoint drivers to be modules (Luca Ceresoli)
   - Enable external clock if present (Luca Ceresoli)

  TI J721E PCIe driver:
   - Disable PHY when probe fails after initializing it (Christophe
     JAILLET)

  MicroSemi Switchtec management driver:
   - Return error to application when command execution fails because an
     out-of-band reset has cleared the device BARs, Memory Space Enable,
     etc (Kelvin Cao)
   - Fix MRPC error status handling issue (Kelvin Cao)
   - Mask out other bits when reading of management VEP instance ID
     (Kelvin Cao)
   - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
     (Kelvin Cao)
   - Add check of event support (Logan Gunthorpe)

  Miscellaneous:
   - Remove unused pci_pool wrappers, which have been replaced by
     dma_pool (Cai Huoqing)
   - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
     Wilczyński)
   - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
     Wilczyński)
   - Fix some sscanf(), sprintf() format mismatches (Krzysztof
     Wilczyński)
   - Update PCI subsystem information in MAINTAINERS (Krzysztof
     Wilczyński)
   - Correct some misspellings (Krzysztof Wilczyński)"

* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
  PCI: Add ACS quirk for Pericom PI7C9X2G switches
  PCI: apple: Configure RID to SID mapper on device addition
  iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
  PCI: apple: Implement MSI support
  PCI: apple: Add INTx and per-port interrupt support
  PCI: kirin: Allow removing the driver
  PCI: kirin: De-init the dwc driver
  PCI: kirin: Disable clkreq during poweroff sequence
  PCI: kirin: Move the power-off code to a common routine
  PCI: kirin: Add power_off support for Kirin 960 PHY
  PCI: kirin: Allow building it as a module
  PCI: kirin: Add MODULE_* macros
  PCI: kirin: Add Kirin 970 compatible
  PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
  PCI: apple: Set up reference clocks when probing
  PCI: apple: Add initial hardware bring-up
  PCI: of: Allow matching of an interrupt-map local to a PCI device
  of/irq: Allow matching of an interrupt-map local to an interrupt controller
  irqdomain: Make of_phandle_args_to_fwspec() generally available
  PCI: Do not enable AtomicOps on VFs
  ...

Merge branch 'pci/misc'

2021-11-05T16:28:47+00:00

- Tidy setup-irq.c comments (Pranay Sanghai)

- Fix misspellings (Krzysztof Wilczyński)

- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)

- Tidy cpqphp code formatting (Krzysztof Wilczyński)

- Remove unused pci_pool wrappers, which have been replaced by dma_pool
  (Cai Huoqing)

- Remove a redundant initialization in __pci_reset_function_locked() (Colin
  Ian King)

- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)

- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)

- Include generic  headers instead of  for cpqphp and vmd
  (Krzysztof Wilczyński)

* pci/misc:
  PCI: vmd: Drop redundant includes of , 
  PCI: cpqphp: Use  instead of 
  MAINTAINERS: Update PCI subsystem information
  PCI: Prefer 'unsigned int' over bare 'unsigned'
  PCI: Remove redundant 'rc' initialization
  PCI: Remove unused pci_pool wrappers
  PCI: cpqphp: Format if-statement code block correctly
  PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
  PCI: hv: Remove unnecessary use of %hx
  PCI: Correct misspelled and remove duplicated words
  PCI: Tidy comments