Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
The value of the constant POWER_FAILURE assigned to the variable rc
after the power fault check is never used for anything, so remove it.
Addresses-Coverity-ID: 1226899 ("Unused value")
Link: https://lore.kernel.org/r/20200923025225.471459-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a PCIe card is hot-removed, the Presence Detect State and Data Link
Layer Link Active bits often do not clear simultaneously. I've seen delays
of up to 244 msec between the two events with Thunderbolt.
After pciehp has brought down the slot in response to the first event, the
other bit may still be set. It's not discernible whether it's set because
a new card is already in the slot or if it will soon clear. So pciehp
tries to bring up the slot and in the latter case fails with a bunch of
messages, some of them at KERN_ERR severity. If the slot is no longer
occupied, the messages are false positives and annoy users.
Stuart Hayes reports the following splat on hot removal:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Timeout waiting for Presence Detect
KERN_ERR pcieport 0000:3c:06.0: pciehp: link training error: status 0x0001
KERN_ERR pcieport 0000:3c:06.0: pciehp: Failed to check link status
Dongdong Liu complains about a similar splat:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Link Down
KERN_INFO iommu: Removing device 0000:87:00.0 from group 12
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pcieport 0000:80:10.0: Data Link Layer Link Active not set in 1000 msec
KERN_ERR pciehp 0000:80:10.0:pcie004: Failed to check link status
Users are particularly irritated to see a bringup attempt even though the
slot was explicitly brought down via sysfs. In a perfect world, we could
avoid this by setting Link Disable on slot bringdown and re-enabling it
upon a Presence Detect State change. In reality however, there are broken
hotplug ports which hardwire Presence Detect to zero, see 80696f991424
("PCI: pciehp: Tolerate Presence Detect hardwired to zero"). Conversely,
PCIe r1.0 hotplug ports hardwire Link Active to zero because Link Active
Reporting wasn't specified before PCIe r1.1. On unplug, some ports first
clear Presence then Link (see Stuart Hayes' splat) whereas others use the
inverse order (see Dongdong Liu's splat). To top it off, there are hotplug
ports which flap the Presence and Link bits on slot bringup, see
6c35a1ac3da6 ("PCI: pciehp: Tolerate initially unstable link").
pciehp is designed to work with all of these variants. Surplus attempts at
slot bringup are a lesser evil than not being able to bring up slots at
all. Although we could try to perfect the behavior for specific hotplug
controllers, we'd risk breaking others or increasing code complexity.
But we can certainly minimize annoyance by emitting only a single message
with KERN_INFO severity if bringup is unsuccessful:
* Drop the "Timeout waiting for Presence Detect" message in
pcie_wait_for_presence(). The sole caller of that function,
pciehp_check_link_status(), ignores the timeout and carries on. It emits
error messages of its own and I don't think this particular message adds
much value.
* There's a single error condition in pciehp_check_link_status() which
does not emit a message. Adding one allows dropping the "Failed to check
link status" message emitted by board_added() if
pciehp_check_link_status() returns a non-zero integer.
* Tone down all messages in pciehp_check_link_status() to KERN_INFO
severity and rephrase them to look as innocuous as possible. To this
end, move the message emitted by pcie_wait_for_link_delay() to its
callers.
As a result, Stuart Hayes' splat becomes:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Cannot train link: status 0x0001
Dongdong Liu's splat becomes:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): No link
The messages now merely serve as information that presence or link bits
were set a little longer than expected. Bringup failures which are not
false positives are still reported, albeit no longer at KERN_ERR severity.
Link: https://lore.kernel.org/linux-pci/20200310182100.102987-1-stuart.w.hayes@gmail.com/
Link: https://lore.kernel.org/linux-pci/1547649064-19019-1-git-send-email-liudongdong3@huawei.com/
Link: https://lore.kernel.org/r/b45e46fd8a6aa6930aaac9d7718c2e4b787a4e5e.1595935071.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use for_each_child_of_node() and for_each_node_by_name() macros instead of open coding them. Link: https://lore.kernel.org/r/20200916062128.190819-1-miaoqinglang@huawei.com Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
For fixing the PF to VF link removal we need to perform some action on every removal of a zdev from the common PCI subsystem. So in preparation re-introduce zpci_remove_device() and use that instead of directly calling the common code functions. This was actually still declared from earlier code but no longer implemented. Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Fix pci_cfg_wait queue locking problem (Bjorn Helgaas)
- Convert PCIe capability PCIBIOS errors to errno (Bolarinwa Olayemi
Saheed)
- Align PCIe capability and PCI accessor return values (Bolarinwa
Olayemi Saheed)
- Fix pci_create_slot() reference count leak (Qiushi Wu)
- Announce device after early fixups (Tiezhu Yang)
PCI device hotplug:
- Make rpadlpar functions static (Wei Yongjun)
Driver binding:
- Add device even if driver attach failed (Rajat Jain)
Virtualization:
- xen: Remove redundant initialization of irq (Colin Ian King)
IOMMU:
- Add pci_pri_supported() to check device or associated PF (Ashok Raj)
- Release IVRS table in AMD ACS quirk (Hanjun Guo)
- Mark AMD Navi10 GPU rev 0x00 ATS as broken (Kai-Heng Feng)
- Treat "external-facing" devices themselves as internal (Rajat Jain)
MSI:
- Forward MSI-X error code in pci_alloc_irq_vectors_affinity() (Piotr
Stankiewicz)
Error handling:
- Clear PCIe Device Status errors only if OS owns AER (Jonathan
Cameron)
- Log correctable errors as warning, not error (Matt Jolly)
- Use 'pci_channel_state_t' instead of 'enum pci_channel_state' (Luc
Van Oostenryck)
Peer-to-peer DMA:
- Allow P2PDMA on AMD Zen and newer CPUs (Logan Gunthorpe)
ASPM:
- Add missing newline in sysfs 'policy' (Xiongfeng Wang)
Native PCIe controllers:
- Convert to devm_platform_ioremap_resource_byname() (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() (Dejin Zheng)
- Remove duplicate error message from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Fix runtime PM imbalance on error (Dinghao Liu)
- Remove dev_err() when handing an error from platform_get_irq()
(Krzysztof Wilczyński)
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for
altera, brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3,
versatile, xgene, xilinx, xilinx-nwl (Rob Herring)
- Default host bridge parent device to the platform device (Rob
Herring)
- Use pci_is_root_bus() instead of tracking root bus number
separately in aardvark, designware (imx6, keystone,
designware-host), mobiveil, xilinx-nwl, xilinx, rockchip, rcar (Rob
Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of
each driver for aardvark, designware-host, host-common, mediatek,
rcar, tegra, v3-semi (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob
Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers
that don't support legacy IRQs (iproc) need to undo this (Rob
Herring)
ARM Versatile PCIe controller driver:
- Drop flag PCI_ENABLE_PROC_DOMAINS (Rob Herring)
Cadence PCIe controller driver:
- Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
(Kishon Vijay Abraham I)
- Remove "mem" from reg binding (Kishon Vijay Abraham I)
- Fix cdns_pcie_{host|ep}_setup() error path (Kishon Vijay Abraham I)
- Convert all r/w accessors to perform only 32-bit accesses (Kishon
Vijay Abraham I)
- Add support to start link and verify link status (Kishon Vijay
Abraham I)
- Allow pci_host_bridge to have custom pci_ops (Kishon Vijay Abraham I)
- Add new *ops* for CPU addr fixup (Kishon Vijay Abraham I)
- Fix updating Vendor ID and Subsystem Vendor ID register (Kishon
Vijay Abraham I)
- Use bridge resources for outbound window setup (Rob Herring)
- Remove private bus number and range storage (Rob Herring)
Cadence PCIe endpoint driver:
- Add MSI-X support (Alan Douglas)
HiSilicon PCIe controller driver:
- Remove non-ECAM HiSilicon hip05/hip06 driver (Rob Herring)
Intel VMD host bridge driver:
- Use Shadow MEMBAR registers for QEMU/KVM guests (Jon Derrick)
Loongson PCIe controller driver:
- Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk() (Tiezhu Yang)
Marvell Aardvark PCIe controller driver:
- Indicate error in 'val' when config read fails (Pali Rohár)
- Don't touch PCIe registers if no card connected (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Setup BAR0 in order to fix MSI (Shmuel Hazan)
Microsoft Hyper-V host bridge driver:
- Fix a timing issue which causes kdump to fail occasionally (Wei Hu)
- Make some functions static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Revert tegra124 raw_violation_fixup (Nicolas Chauvet)
- Remove PLL power supplies (Thierry Reding)
Qualcomm PCIe controller driver:
- Change duplicate PCI reset to phy reset (Abhishek Sahu)
- Add missing ipq806x clocks in PCIe driver (Ansuel Smith)
- Add missing reset for ipq806x (Ansuel Smith)
- Add ext reset (Ansuel Smith)
- Use bulk clk API and assert on error (Ansuel Smith)
- Add support for tx term offset for rev 2.1.0 (Ansuel Smith)
- Define some PARF params needed for ipq8064 SoC (Ansuel Smith)
- Add ipq8064 rev2 variant (Ansuel Smith)
- Support PCI speed set for ipq806x (Sham Muthayyan)
Renesas R-Car PCIe controller driver:
- Use devm_pci_alloc_host_bridge() (Rob Herring)
- Use struct pci_host_bridge.windows list directly (Rob Herring)
- Convert rcar-gen2 to use modern host bridge probe functions (Rob
Herring)
TI J721E PCIe driver:
- Add TI J721E PCIe host and endpoint driver (Kishon Vijay Abraham I)
Xilinx Versal CPM PCIe controller driver:
- Add Versal CPM Root Port driver and YAML schema (Bharat Kumar
Gogada)
MicroSemi Switchtec management driver:
- Add missing __iomem and __user tags to fix sparse warnings (Logan
Gunthorpe)
Miscellaneous:
- Replace http:// links with https:// (Alexander A. Klimov)
- Replace lkml.org, spinics, gmane with lore.kernel.org (Bjorn
Helgaas)
- Remove unused pci_lost_interrupt() (Heiner Kallweit)
- Move PCI_VENDOR_ID_REDHAT definition to pci_ids.h (Huacai Chen)
- Fix kerneldoc warnings (Krzysztof Kozlowski)"
* tag 'pci-v5.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (113 commits)
PCI: Fix kerneldoc warnings
PCI: xilinx-cpm: Add Versal CPM Root Port driver
PCI: xilinx-cpm: Add YAML schemas for Versal CPM Root Port
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: Remove dev_err() when handing an error from platform_get_irq()
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
PCI: switchtec: Add missing __iomem tag to fix sparse warnings
PCI: switchtec: Add missing __iomem and __user tags to fix sparse warnings
PCI: rpadlpar: Make functions static
PCI/P2PDMA: Allow P2PDMA on AMD Zen and newer CPUs
PCI: Release IVRS table in AMD ACS quirk
PCI: Announce device after early fixups
PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken
PCI: Remove unused pci_lost_interrupt()
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
...
- Fix several kerneldoc warnings (Krzysztof Kozlowski) * pci/doc: PCI: Fix kerneldoc warnings
Fix kerneldoc warnings, e.g., $ make W=1 drivers/pci/ drivers/pci/ats.c:196: warning: Function parameter or member 'pdev' not described in 'pci_enable_pri' drivers/pci/ats.c:196: warning: Function parameter or member 'reqs' not described in 'pci_enable_pri' ... Link: https://lore.kernel.org/r/20200729201224.26799-2-krzk@kernel.org Link: https://lore.kernel.org/r/20200729201224.26799-3-krzk@kernel.org Link: https://lore.kernel.org/r/20200729201224.26799-4-krzk@kernel.org Link: https://lore.kernel.org/r/20200729201224.26799-5-krzk@kernel.org Link: https://lore.kernel.org/r/20200729201224.26799-6-krzk@kernel.org Link: https://lore.kernel.org/r/20200729201224.26799-7-krzk@kernel.org Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sparse tool report build warnings as follows: drivers/pci/hotplug/rpadlpar_core.c:355:5: warning: symbol 'dlpar_remove_pci_slot' was not declared. Should it be static? drivers/pci/hotplug/rpadlpar_core.c:461:12: warning: symbol 'rpadlpar_io_init' was not declared. Should it be static? drivers/pci/hotplug/rpadlpar_core.c:473:6: warning: symbol 'rpadlpar_io_exit' was not declared. Should it be static? Those functions are not used outside of this file, so mark them static. Also mark rpadlpar_io_exit() as __exit. Link: https://lore.kernel.org/r/20200721151735.41181-1-weiyongjun1@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>