Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...