commit 7fa3f73f6c8ddc5f0425b50fb2a626a782ef7d12 upstream.
nvme_tcp_recv_data() completes a request once the current C2HData PDU
has been consumed. Nothing compares the total bytes received against
the length the command asked for: struct nvme_tcp_request has no
receive-side counter, queue->data_remaining is per queue, and
blk_mq_end_request() completes for blk_rq_bytes(rq) unconditionally
with no residual concept anywhere above.
A controller can therefore answer a 4096-byte read with 512 bytes and
have it reported as a complete read; user space then gets 4096 bytes of
which 3584 are whatever was already in the page. I reproduced that with
a test target.
Count the bytes received and refuse to complete a successful read whose
count does not match, at the two NVME_TCP_F_DATA_SUCCESS paths and in
nvme_tcp_process_nvme_cqe(). The success test shifts req->status right
by one, because the driver keeps the wire value there and shifts it on
completion, so the check must see what the completion path will see.
Only REQ_OP_READ is checked, because there the length comes from the
sectors the request covers; a passthrough command is built by its
submitter, which picks both command and buffer, so the kernel has
nothing to compare against.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Cc: stable@vger.kernel.org
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6efbc52237facda35d2d874fe1765bb4839275d8 upstream.
nvme_tcp_handle_r2t() does not check the direction of the request the
R2T refers to. A malicious controller can send an R2T for a READ and
the host will answer it: nvme_tcp_setup_h2c_data_pdu() builds the
H2CData header and nvme_tcp_try_send_data() sends the request's data
buffer. That buffer is the READ destination, so its contents go to the
controller.
The command then completes normally and nothing is logged.
Against a test controller that answers every READ with an R2T, a 4096
byte buffered read returned all 4096 bytes, split over two R2Ts. The
pages contained stale kernel data, including an array of struct page
pointers.
Reject an R2T for a request that is not a write.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Cc: stable@vger.kernel.org
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a4aa9e6ad3e35f8e24d5eaf38ee4d437075fb36 upstream.
Commit 25e5cb780e62 ("nvme-tcp: fix possible crash in write_zeroes
processing") established that blk_rq_payload_bytes() must not be read
without first checking blk_rq_nr_phys_segments(), and recorded the
result in nvme_tcp_setup_cmd_pdu() as req->data_len. The receive side
was left as it was.
The two differ for REQ_OP_WRITE_ZEROES, which has no physical segments
but a non-zero blk_rq_bytes(), so setup leaves req->iter untouched
while the receive gate lets a C2HData through and nvme_tcp_recv_data()
copies into whatever the previous command on that tag left there. The
driver-private area is zeroed only when the tag set is allocated.
Reproduced with a test target that leaves a residual iterator on a tag
and then sends a C2HData for a WRITE_ZEROES command on the same tag:
BUG: KASAN: wild-memory-access in _copy_to_iter+0x642/0x1330
Write of size 512 at addr ffe728c2175dfa81 by task kworker/0:1H/103
CPU: 0 UID: 0 PID: 103 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMETCP-gf5098b6bae76 #1 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: nvme_tcp_wq nvme_tcp_io_work
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
kasan_report+0xce/0x100
? _copy_to_iter+0x642/0x1330
kasan_check_range+0x105/0x1b0
__asan_memcpy+0x3c/0x60
_copy_to_iter+0x642/0x1330
? __pfx_sock_has_perm+0x10/0x10
? worker_thread+0x45b/0xd10
? __pfx__copy_to_iter+0x10/0x10
? _raw_spin_lock_bh+0x83/0xe0
? __pfx__raw_spin_lock_bh+0x10/0x10
__skb_datagram_iter+0xf3/0x820
? __pfx_simple_copy_to_iter+0x10/0x10
? __asan_memcpy+0x3c/0x60
? skb_copy_bits+0x58d/0x830
skb_copy_datagram_iter+0x37/0x120
nvme_tcp_recv_skb+0xa07/0x4320
? __pfx_nvme_tcp_recv_skb+0x10/0x10
__tcp_read_sock+0x1ab/0x810
? __pfx_nvme_tcp_recv_skb+0x10/0x10
? __pfx_lock_sock_nested+0x10/0x10
? __pfx___tcp_read_sock+0x10/0x10
nvme_tcp_try_recv+0x152/0x1e0
? __pfx_nvme_tcp_try_recv+0x10/0x10
? __pfx_mutex_unlock+0x10/0x10
nvme_tcp_io_work+0x1e4/0x6c0
? __schedule+0x181a/0x49f0
? __pfx_nvme_tcp_io_work+0x10/0x10
process_one_work+0x633/0x1030
Keep the blk_rq_payload_bytes() test and add req->data_len to it. The
old test is what rejects a C2HData naming a tag that is no longer in
flight, because blk_update_request() zeroes rq->__data_len on
completion; req->data_len and req->curr_bio are driver-private and
survive completion, so they cannot stand in for it. Setup initialises
the iterator only when both req->curr_bio and req->data_len are set, so
the gate now tests the same two.
Fixes: 25e5cb780e62 ("nvme-tcp: fix possible crash in write_zeroes processing")
Cc: stable@vger.kernel.org
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08660a5c8d497f43191635d97efd31cd35051f15 upstream.
nvme_pci_configure_admin_queue() enables the controller and then requests
the admin queue interrupt. If queue_request_irq() fails it returns without
disabling the controller, and no caller compensates: nvme_pci_enable() only
frees the IRQ vectors and calls pci_disable_device(), after which
nvme_dev_disable() treats the controller as dead and skips nvme_disable_ctrl().
The controller is left enabled (CC.EN set) on this error path.
Disable it in the failure path, while the PCI device is still enabled so the
CC.EN clear handshake completes.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: b60503ba432b ("NVMe: New driver")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bededeaaeff404978a5a8e2a605a6c3017cddd3e upstream.
nvme_setup_discard() always maps sizeof(struct nvme_dsm_range) *
NVME_DSM_MAX_RANGES = 4096 bytes as the DSM payload however many ranges
the command declares, because some devices ignore the 'Number of Ranges'
field - the Fixes: commit records two that read past the declared ranges.
A single-range discard fills only the first 16 bytes.
Normally the buffer comes from kzalloc() and the other 4080 bytes are
zero. When that allocation fails the code falls back to the
per-controller ctrl->discard_page, which nvme_init_ctrl() obtains with
alloc_page(GFP_KERNEL) and nothing ever zeroes, so those 4080 bytes are
whatever the page last held and are handed to the controller. Reaching
it requires the kzalloc(GFP_ATOMIC | __GFP_NOWARN) to fail, that is
memory pressure; it is not remotely triggerable. Failing the allocation
under KMSAN reproduces it, with the leaked tail full of vmemmap struct
page pointers. The extent in the report is a partial transfer of the
payload, not the whole 4096 bytes; the 16-byte boundary in it is the one
declared range:
[ 11.991601] BUG: KMSAN: uninit-value in dma_map_phys+0x14c8/0x1900
[ 11.991969] dma_map_phys+0x14c8/0x1900
[ 11.992220] dma_map_page_attrs+0xcf/0x130
[ 11.992485] e1000_xmit_frame+0x4099/0x6d10
[ 11.992768] dev_hard_start_xmit+0x22f/0xa80
[ 11.993068] sch_direct_xmit+0x35c/0xcb0
[ 11.993315] __dev_queue_xmit+0x1ee5/0x5eb0
[ 11.993608] ip_finish_output2+0x1903/0x1c30
[ 11.993881] ip_finish_output+0x288/0x870
[ 11.994125] ip_output+0x15e/0x400
[ 11.994365] __ip_queue_xmit+0x1e85/0x1fb0
[ 11.994639] ip_queue_xmit+0x60/0x80
[ 11.994899] __tcp_transmit_skb+0x4e71/0x5fa0
[ 11.995210] tcp_write_xmit+0x3a36/0x9160
[ 11.995533] __tcp_push_pending_frames+0xc5/0x3c0
[ 11.995854] tcp_push+0x7dc/0x840
[ 11.996076] tcp_sendmsg_locked+0x766c/0x8400
[ 11.996371] tcp_sendmsg+0x4b/0x90
[ 11.996572] inet_sendmsg+0x134/0x2a0
[ 11.996823] __sock_sendmsg+0x265/0x360
[ 11.997076] sock_sendmsg+0x100/0x1e0
[ 11.997293] nvme_tcp_try_send+0x196f/0x6370
[ 11.997605] nvme_tcp_queue_rq+0x1d54/0x20b0
[ 11.997882] blk_mq_dispatch_rq_list+0x5ee/0x2e50
[ 11.998175] __blk_mq_sched_dispatch_requests+0x16dc/0x24a0
[ 11.998539] blk_mq_sched_dispatch_requests+0x11b/0x2c0
[ 11.998865] blk_mq_run_work_fn+0x13b/0x280
[ 11.999146] process_scheduled_works+0x966/0x1ad0
[ 11.999465] worker_thread+0xe44/0x1480
[ 11.999709] kthread+0x53b/0x600
[ 11.999927] ret_from_fork+0x29f/0x7c0
[ 12.000191] ret_from_fork_asm+0x1a/0x30
[ 12.000460]
[ 12.000558] Uninit was created at:
[ 12.000788] __alloc_frozen_pages_noprof+0x8bf/0xd30
[ 12.001096] alloc_pages_mpol+0x1d0/0x5f0
[ 12.001326] alloc_pages_noprof+0x102/0x290
[ 12.001627] nvme_init_ctrl+0x5a3/0x9f0
[ 12.001891] nvme_tcp_create_ctrl+0xd75/0x19b0
[ 12.002170] nvmf_dev_write+0x4c68/0x4fd0
[ 12.002426] vfs_write+0x587/0x1a10
[ 12.002636] __x64_sys_write+0x207/0x4f0
[ 12.002874] x64_sys_call+0x2ff0/0x3ea0
[ 12.003123] do_syscall_64+0x147/0x3b0
[ 12.003400] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 12.003680]
[ 12.003777] Bytes 16-2843 of 2844 are uninitialized
[ 12.004068] Memory access of size 2844 starts at ffff888109f82000
[ 12.004412]
[ 12.004530] CPU: 0 UID: 0 PID: 101 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMECTL-gf5098b6bae76 #1 PREEMPT(lazy)
[ 12.005127] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 12.005762] Workqueue: kblockd blk_mq_run_work_fn
[ 12.006073] =====================================================
Allocate the page with __GFP_ZERO. The single allocation site covers
every use of it: bytes no discard has written stay zero, and bytes one
did write hold that controller's own range list, which it has already
been sent.
Fixes: 530436c45ef2 ("nvme: Discard workaround for non-conformant devices")
Cc: stable@vger.kernel.org
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22eb631bf86ee3246f47885e4fa94154a46863e4 upstream.
nvme_fc_create_hw_io_queues() will call __nvme_fc_delete_hw_queue() for the
last queue on which __nvme_fc_create_hw_queue() reported an error when deleting
all the io queues if they cannot all be created. This is incorrect since the
last queue did not actually get created.
The most recent change to this code was commit 17a1ec08ce70 ("nvme/fc: simplify
error handling of nvme_fc_create_hw_io_queues") which moved the cleanup to the
delete_queues: label and changed the loop bounds, however the code was not
correct prior to this change in a different way. The original commit
e399441de911 ("nvme-fabrics: Add host support for FC transport") had a
different error which called __nvme_fc_delete_hw_queue() on queue index 0 which
is used for the admin queue.
Fix this by correcting the initial loop index when deleting the io queues.
Fixes: 17a1ec08ce70 ("nvme/fc: simplify error handling of nvme_fc_create_hw_io_queues")
Fixes: e399441de911 ("nvme-fabrics: Add host support for FC transport")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-6
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36ac05f7cfd59d90c597071304b14e98090d5dd1 ]
nvme uses page_frag_cache to preallocate PDU for each preallocated request
of block device. Block devices are created in parallel threads,
consequently page_frag_cache is used in not thread-safe manner.
That leads to incorrect refcounting of backstore pages and premature free.
That can be catched by !sendpage_ok inside network stack:
WARNING: CPU: 7 PID: 467 at ../net/core/skbuff.c:6931 skb_splice_from_iter+0xfa/0x310.
tcp_sendmsg_locked+0x782/0xce0
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x8b/0xa0
nvme_tcp_try_send_cmd_pdu+0x149/0x2a0
Then random panic may occur.
Fix that by serializing the usage of page_frag_cache.
Fixes: 4e893ca81170 ("nvme_core: scan namespaces asynchronously")
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull block fixes from Jens Axboe:
- blk-cgroup locking rework and fixes:
- fix a use-after-free in __blkcg_rstat_flush()
- defer freeing policy data until after an RCU grace period
- defer the blkcg css_put until the blkg is unlinked from
the queue
- unwind the queue_lock nesting under RCU / blkcg->lock
across the lookup, create, associate and destroy paths
- NVMe fixes via Keith:
- Fix a crash and memory leak during invalid cdev teardown,
and related cdev cleanups (Maurizio, John)
- nvmet fixes: handle TCP_CLOSING in the tcp state_change
handler, reject short AUTH_RECEIVE buffers, handle inline
data with a nonzero offset in rdma, fix an sq refcount leak,
and allocate ana_state with the port (Maurizio, Michael,
Bryam, Wentao, Rosen)
- nvme-fc fix to not cancel requests on an IO target before it
is initialized (Mohamed)
- nvme-apple fix to prevent shared tags across queues on Apple
A11 (Nick)
- Various smaller fixes and cleanups (John)
- MD fixes via Yu Kuai:
- raid1/raid10 fixes for writes_pending and barrier reference
leaks on write and discard failures, plus REQ_NOWAIT handling
fixes (Abd-Alrhman)
- raid5 discard accounting and validation, and a batch of fixes
for stripe batch races (Yu Kuai, Chen)
- Protect raid1 head_position during read balancing (Chen)
- block bio-integrity fixes: correct an error injection static key
decrement, fix GFP flag confusion in bio_integrity_alloc_buf(), and
handle REQ_OP_ZONE_APPEND in __bio_integrity_action() (Christoph)
- Fixes for bio_iov_iter_bounce_write(): revert the iov_iter after a
short copy, and respect the iov_iter nofault flag (Qu)
- Invalidate the cached plug timestamp after a task switch, and clear
PF_BLOCK_TS in copy_process() (Usama)
- Fix the IORING_URING_CMD_REISSUE flags check in blkdev_uring_cmd()
(Yitang)
- Remove a redundant plug in __submit_bio() (Wen)
- Don't warn when reclassifying a busy socket lock in nbd (Deepanshu)
* tag 'block-7.2-20260625' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (45 commits)
block: handle REQ_OP_ZONE_APPEND in __bio_integrity_action
block: fix GFP_ flags confusion in bio_integrity_alloc_buf
block, bfq: don't grab queue_lock to initialize bfq
mm/page_io: don't nest queue_lock under rcu in bio_associate_blkg_from_page()
blk-cgroup: don't nest queue_lock under blkcg->lock in blkcg_destroy_blkgs()
blk-cgroup: don't nest queue_lock under rcu in bio_associate_blkg()
blk-cgroup: don't nest queue_lock under rcu in blkg_lookup_create()
blk-cgroup: don't nest queue_lock under rcu in blkcg_print_blkgs()
blk-cgroup: delay freeing policy data after rcu grace period
blk-cgroup: protect iterating blkgs with blkcg->lock in blkcg_print_stat()
md/raid5: avoid R5_Overlap races while breaking stripe batches
md/raid5: use stripe state snapshot in break_stripe_batch_list()
blk-cgroup: defer blkcg css_put until blkg is unlinked from queue
blk-cgroup: fix UAF in __blkcg_rstat_flush()
block, bfq: protect async queue reset with blkcg locks
nbd: don't warn when reclassifying a busy socket lock
block: fix incorrect error injection static key decrement
md/raid5: let stripe batch bm_seq comparison wrap-safe
md/raid1: protect head_position for read balance
md/raid1: free r1_bio when REQ_NOWAIT is set and read would block on retry
...
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*) that worked
around a WiFi device defect; use a quirk or boot-time
"pci=pcie_bus_tune_*" kernel parameter instead (Bjorn Helgaas)
- Always lift 2.5GT/s restriction in PCIe failed link retraining to
avoid clamping a link to 2.5GT/s after hot-plug changes the device
(Maciej W. Rozycki)
- Request bus reassignment when not probe-only to fix an enumeration
regression on Marvell CN106XX and possibly other DT-based systems
(Ratheesh Kannoth)
- Fix procfs race between pci_proc_init() and pci_bus_add_device()
that resulted in 'proc_dir_entry ... already registered' warnings
and pointer corruption (Krzysztof Wilczyński)
- Fix sysfs race that causes 'duplicate filename' warnings and boot
panics by converting PCI resource files to static attributes
(Krzysztof Wilczyński)
- Expose sysfs 'resourceN_resize' attributes only on platforms with
PCI mmap (Krzysztof Wilczyński)
- Require CAP_SYS_ADMIN to write to sysfs 'resourceN_resize'
attributes (Krzysztof Wilczyński)
- Add security_locked_down(LOCKDOWN_PCI_ACCESS) to alpha PCI resource
mmap path to match the generic path (Krzysztof Wilczyński)
- Use kstrtobool() to parse the 'rom' attribute input to avoid the
unexpected behavior of enabling the ROM when writing '0' with no
trailing newline (Krzysztof Wilczyński)
Resource management:
- Improve resource claim logging for debuggability (Ilpo Järvinen)
- Clean up several uses of const parameters (Ilpo Järvinen)
- Check option ROM header signatures and lengths before accessing to
avoid page faults and alignment faults (Guixin Liu)
ASPM:
- Don't reconfigure ASPM when entering low-power D-state; only do it
when returning back to D0 (Carlos Bilbao)
Power management:
- During suspend, set power state to 'unknown' for all devices, not
just those with drivers (Lukas Wunner)
- Skip restoring Resizable BARs and VF Resizable BARs if device
doesn't respond to config reads, to avoid invalid array accesses
(Marco Nenciarini)
- Add pci_suspend_retains_context() so drivers can tell whether
devices retain internal state across suspend/resume, since some
platforms reset devices on suspend; use this in nvme to avoid
issues on Qcom RCs (Manivannan Sadhasivam)
Power control:
- Only to power on/off devices that actually support power control to
avoid poking at incompatible devices mentioned in DT (Manivannan
Sadhasivam)
Virtualization and resets:
- Log device readiness timeouts as errors, not warnings, because the
device is likely unusable in this case (Bjorn Helgaas)
- Wait for device readiness after soft reset (D3hot ->
D0uninitialized transition), when the device may respond with
Request Retry Status (RRS) if it needs more time to initialize
(Bjorn Helgaas)
- Drop unnecessary retries when restoring BARs because resets should
now already include all required delays (Lukas Wunner)
- Avoid FLR for MediaTek MT7925 WiFi, where FLR fails after a VM
terminates uncleanly (Jose Ignacio Tornos Martinez)
- Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems,
which seem not to support it correctly (Jose Ignacio Tornos
Martinez)
Peer-to-peer DMA:
- Prevent P2PDMA as well as CPU access to non-mappable BARs, e.g.,
s390 ISM BARs (Matt Evans)
- Add Intel QAT, DSA, IAA devices to whitelist (Lukas Wunner)
Endpoint framework:
- Add endpoint controller APIs for use by function drivers to
discover auxiliary blocks like DMA engines (Koichiro Den)
- Remember DesignWare eDMA engine base/size and expose them via the
EPC aux-resource API (Koichiro Den)
- Add endpoint embedded doorbell fallback, used if MSI allocation
fails (Koichiro Den)
- Validate BAR index and remove dead BAR read in endpoint doorbell
test (Carlos Bilbao)
- Unwind MSI/MSI-X vectors if NTB initialization fails part-way
through (Koichiro Den)
- Cache sleepable pci_irq_vector() value at ISR setup to avoid
calling it from hardirq context (Koichiro Den)
- Call sleepable pci_epc_raise_irq() from a work item instead of
atomic context, e.g., when setting bits in NTB peer doorbells in
the ntb_peer_db_set() path (Koichiro Den)
- Report 0-based vNTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Prevent configfs writes to vNTB db_count and other values that are
already in use after EPC attach (Koichiro Den)
- Account for vNTB db_valid reserved slots (link event 0 and
historically skipped slot 1) so they don't appear as valid
doorbells (Koichiro Den)
- Implement vNTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors and avoid thundering herds (Koichiro Den)
- Report 0-based NTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Fix doorbell bitmask and IRQ vector handling to clear only
specified bits, use the correct vector for non-contiguous Linux IRQ
numbers, and validate incoming vectors (Koichiro Den)
- Implement NTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors (Koichiro Den)
Native PCIe controller infrastructure:
- Add pci_host_common_link_train_delay() for the mandatory delay
after > 5GT/s Link training completes and use it for cadence HPA,
j721e, LGA; dwc; aardvark, mediatek-gen3, rzg3s (Hans Zhang)
- Protect root bus removal with rescan lock in altera, brcmstb,
cadence, dwc, iproc, mediatek, plda, rockchip to prevent
use-after-free or crashes when racing with sysfs rescan or hotplug
(Hans Zhang)
- Add pci_host_common_parse_ports() for use by any native driver to
parse Root Port properties (per-Link features like width, speed,
PHY, power and reset control, etc should be described in Root Port
stanzas, not the host bridge; currently only reset GPIOs
implemented) (Sherry Sun)
New native PCIe controller drivers:
- Add DT binding and driver for UltraRISC DP1000 PCIe controller
(Xincheng Zhang, Jia Wang)
Altera PCIe controller driver:
- Do not dispose of the parent IRQ mapping, which belongs to the
parent interrupt controller (Mahesh Vaidya)
- Fix chained IRQ handler ordering issue and resource leaks on probe
failure (Mahesh Vaidya)
AMD MDB PCIe controller driver:
- Assert PERST# on shutdown so any connected Endpoints are held in
reset during shutdown (Sai Krishna Musham)
Amlogic Meson PCIe controller driver:
- Propagate devm_add_action_or_reset() failure to fix probe error
path (Shuvam Pandey)
- Add .remove() callback to deinitialize the host bridge and power
off the PHY (Shuvam Pandey)
Broadcom iProc PCIe controller driver:
- Restore .map_irq() assignment; its removal broke INTx on the iproc
platform bus driver (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- No change, but products using certain WiFi devices may be affected
by removal of CONFIG_PCIE_BUS_* (see above)
Freescale i.MX6 PCIe controller driver:
- Move IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling into the core reset
functions (Richard Zhu)
- Assert PERST# before enabling regulators to ensure that even if
power is enabled, endpoint stays inactive until REFCLK is stable
(Sherry Sun)
- Parse reset properties in Root Port nodes (falling back to host
bridge) to help support Key E connectors and the pwrctrl framework
(Sherry Sun)
- Configure i.MX95 REF_USE_PAD before PHY reset (Richard Zhu)
- Assert i.MX95 ref_clk_en after reference clock stabilizes (Richard
Zhu)
- Integrate new pwrctrl API for DTs with Root Port-level power
supplies (Sherry Sun)
Intel Gateway PCIe controller driver:
- Enable clock before PHY init for correct ordering (Florian Eckert)
- Add .start_link() callback so the driver works again (Florian
Eckert)
- Stop overwriting the ATU base address discovered by
dw_pcie_get_resources() (Florian Eckert)
- Add DT 'atu' region since this is hardware-specific, and fall back
to driver default if lacking (Florian Eckert)
Loongson PCIe controller driver:
- Ignore downstream devices only on internal bridges to avoid
Loongson hardware issue (Rong Zhang)
- Quirk old Loongson-3C6000 bridges that advertise incorrect
supported link speeds (Ziyao Li)
Marvell MVEBU PCIe controller driver:
- Use fixed-width interrupt masks to avoid truncation in 64-bit
builds (Rosen Penev)
MediaTek PCIe controller driver:
- Use FIELD_PREP() to fix incorrect operator precedence in
PCIE_FTS_NUM_L0 (Li RongQing)
- Fix IRQ domain leak when port fails to enable (Manivannan
Sadhasivam)
- Use actual physical address for MSI message address instead of
virt_to_phys() (Manivannan Sadhasivam)
- Add EcoNet EN7528 to DT binding (Caleb James DeLisle)
MediaTek PCIe Gen3 controller driver:
- Deassert PCIE_PHY_RSTB so REFCLK is stable for at least 100ms
(PCIE_T_PVPERL_MS) before deasserting PERST# (Jian Yang)
- Add .shutdown() to assert PERST# before powering down device (Jian
Yang)
- Do full device power down on removal, including asserting PERST#,
when removing driver (Chen-Yu Tsai)
- Fix a 'failed to create pwrctrl devices' error message that was
inadvertently skipped (Chen-Yu Tsai)
NVIDIA Tegra194 PCIe controller driver:
- Program the DesignWare PORT_AFR L1 entrance latency based on the
'aspm-l1-entry-delay-ns' DT property (Manikanta Maddireddy)
Qualcomm PCIe controller driver:
- Add Eliza SoC compatible in DT binding (Krishna Chaitanya Chundru)
- Set max OPP during resume so DBI register accesses don't fail with
NoC errors (Qiang Yu)
- Add pci_host_common_d3cold_possible() to determine whether
downstream devices are already in D3hot and wakeup-enabled devices
are capable of generating PME from D3cold (Krishna Chaitanya
Chundru)
- Add .get_ltssm() callback to get the LTSSM status without DBI,
since DBI may be inaccessible after PME_Turn_Off (Krishna Chaitanya
Chundru)
- Power down PHY via PARF_PHY_CTRL before disabling rails/clocks to
avoid power leakage (Krishna Chaitanya Chundru)
- Decide whether suspend should put the link in L2 and power down
using pci_host_common_d3cold_possible() instead of checking whether
ASPM L1 is enabled (Krishna Chaitanya Chundru)
- Add qcom D3cold support to tear down interconnect bandwidth and OPP
votes (Krishna Chaitanya Chundru)
- Handle unsupported mixed PERST#/PHY DT configurations, e.g., PHY in
RP node while PERST# is in the RC node, but warn about the DT issue
(Qiang Yu)
- Program T_POWER_ON based on DT 't-power-on-us' property in case
hardware advertises incorrect values (Krishna Chaitanya Chundru)
- Disable ASPM L0s for SA8775P (Shawn Guo)
- Initialize DWC MSI lock for firmware-managed ECAM hosts, which
don't use the dw_pcie_host_init() path that initializes the lock
(Yadu M G)
Renesas RZ/G3S PCIe controller driver:
- Add RZ/V2N DT support (Lad Prabhakar)
SOPHGO PCIe controller driver:
- Add 'dma-coherent' DT property for sg2042-pcie driver (Han Gao)
Synopsys DesignWare PCIe controller driver:
- Apply ECRC TLP Digest workaround for all DesignWare cores prior to
5.10a, not just 4.90a and 5.00a (Manikanta Maddireddy)
- Use common struct dw_pcie 'mode' rather than duplicating it in
artpec6, dra7xx, dwc-pcie, and keembay driver structs (Hans Zhang)
- Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs to reduce
boilerplate and fix a seq_file memory leak by including a
.release() callback (Hans Zhang)
- Fix a signedness bug in fault injection test code (Dan Carpenter)
- Avoid NULL pointer dereference when tearing down debugfs for
controller that lacks RAS DES capability (Shuvam Pandey)
MicroSemi Switchtec management driver:
- Add Gen6 Device IDs (Ben Reed)
Miscellaneous:
- Remove unused gpio.h include from amd-mdb, designware-plat, fu740,
visconti drivers (Andy Shevchenko)
- Fix typos in documentation (josh ziegler)
- Use FIELD_MODIFY() instead of open-coding it (Hans Zhang)"
* tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (168 commits)
PCI/sysfs: Use kstrtobool() to parse the ROM attribute input
PCI/sysfs: Limit BAR resize attribute scope to platforms with PCI mmap
PCI/sysfs: Remove pci_create_legacy_files() and pci_sysfs_init()
PCI/sysfs: Convert legacy I/O and memory attributes to static definitions
PCI/sysfs: Add __weak pci_legacy_has_sparse() helper
alpha/PCI: Compute legacy size in pci_mmap_legacy_page_range()
PCI: Add macros for legacy I/O and memory address space sizes
PCI/sysfs: Remove pci_{create,remove}_sysfs_dev_files()
alpha/PCI: Convert resource files to static attributes
alpha/PCI: Add static PCI resource attribute macros
alpha/PCI: Remove WARN from __pci_mmap_fits() and __legacy_mmap_fits()
alpha/PCI: Fix __pci_mmap_fits() overflow for zero-length BARs
alpha/PCI: Use PCI resource accessor macros
alpha/PCI: Use BAR index in sysfs attr->private instead of resource pointer
alpha/PCI: Add security_locked_down() check to pci_mmap_resource()
PCI/sysfs: Limit pci_sysfs_init() late_initcall compile scope
PCI/sysfs: Add stubs for pci_{create,remove}_sysfs_dev_files()
PCI/sysfs: Warn about BAR resize failure in __resource_resize_store()
PCI/sysfs: Convert PCI resource files to static attributes
PCI/proc: Fix race between pci_proc_init() and pci_bus_add_device()
...
Pull NVMe fixes from Keith:
"- Apple A11 quirk for sharing tags across admin and IO queues (Nick)
- Target fix for short AUTH_RECEIVE buffers (Michael)
- Target fix for SQ refcount leak (Wentao)
- Target RDMA handling inline data with nonzero offset (Bryam)
- Target TCP fix handling the TCP_CLOSING state (Maurizio)
- FC abort fixes in early initialization (Mohamed)
- Controller device teardown fixes (Maurizio, John)
- Allocate the target ana_state with the port (Rosen)
- Quieten sparse and sysfs symbol warnings (John)"
* tag 'nvme-7.2-2026-06-23' of git://git.infradead.org/nvme:
nvmet-tcp: handle TCP_CLOSING state in nvmet_tcp_state_change
nvmet-auth: reject short AUTH_RECEIVE buffers
nvme-fc: Do not cancel requests in io target before it is initialized
nvme: make nvme_add_ns{_head}_cdev return void
nvme: make some sysfs diagnostic structures static
nvmet-rdma: handle inline data with a nonzero offset
nvme: target: allocate ana_state with port
nvme: fix crash and memory leak during invalid cdev teardown
nvmet: fix refcount leak in nvmet_sq_create()
nvme: quieten sparse warning in valid LBA size check
nvme-apple: Prevent shared tags across queues on Apple A11