linux-stable.git/drivers/net, branch v6.6

iavf: in iavf_down, disable queues when removing the driver

2023-10-26T00:48:31+00:00

In iavf_down, we're skipping the scheduling of certain operations if
the driver is being removed. However, the IAVF_FLAG_AQ_DISABLE_QUEUES
request must not be skipped in this case, because iavf_close waits
for the transition to the __IAVF_DOWN state, which happens in
iavf_virtchnl_completion after the queues are released.

Without this fix, "rmmod iavf" takes half a second per interface that's
up and prints the "Device resources not yet released" warning.

Fixes: c8de44b577eb ("iavf: do not process adminq tasks when __IAVF_IN_REMOVE_TASK is set")
Signed-off-by: Michal Schmidt 
Reviewed-by: Wojciech Drewek 
Tested-by: Rafal Romanowski 
Tested-by: Jacob Keller 
Signed-off-by: Jacob Keller 
Link: https://lore.kernel.org/r/20231025183213.874283-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski

i40e: Fix wrong check for I40E_TXR_FLAGS_WB_ON_ITR

2023-10-25T00:03:29+00:00

The I40E_TXR_FLAGS_WB_ON_ITR is i40e_ring flag and not i40e_pf one.

Fixes: 8e0764b4d6be42 ("i40e/i40evf: Add support for writeback on ITR feature for X722")
Signed-off-by: Ivan Vecera 
Tested-by: Pucha Himasekhar Reddy  (A Contingent worker at Intel)
Signed-off-by: Jacob Keller 
Link: https://lore.kernel.org/r/20231023212714.178032-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski

gtp: fix fragmentation needed check with gso

2023-10-24T10:02:02+00:00

Call skb_gso_validate_network_len() to check if packet is over PMTU.

Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Pablo Neira Ayuso 
Signed-off-by: Paolo Abeni

sfc: cleanup and reduce netlink error messages

2023-10-23T22:47:47+00:00

Reduce the length of netlink error messages as they are likely to be
truncated anyway. Additionally, reword netlink error messages so they
are more consistent with previous messages.

Fixes: 9dbc8d2b9a02 ("sfc: add decrement ipv6 hop limit by offloading set hop limit actions")
Fixes: 3c9561c0a5b9 ("sfc: support TC decap rules matching on enc_ip_tos")
Reported-by: kernel test robot 
Closes: https://lore.kernel.org/oe-kbuild-all/202310202136.4u7bv0hp-lkp@intel.com/
Signed-off-by: Pieter Jansen van Vuuren 
Reviewed-by: Edward Cree 
Link: https://lore.kernel.org/r/20231020140149.30490-1-pieter.jansen-van-vuuren@amd.com
Signed-off-by: Jakub Kicinski

r8152: Block future register access if register access fails

2023-10-22T10:46:18+00:00

Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.

The first problem is that the r8152 driver often uses code patterns
similar to this:
  x = read_register()
  x = x | SOME_BIT;
  write_register(x);

...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad18959 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.

It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.

The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.

One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.

On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
   things recover.

The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.

On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).

Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.

When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.

Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller

r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE

2023-10-22T10:46:18+00:00

Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.

This is a no-op change and just a search and replace.

Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller

r8152: Check for unplug in r8153b_ups_en() / r8153c_ups_en()

2023-10-22T10:46:18+00:00

If the adapter is unplugged while we're looping in r8153b_ups_en() /
r8153c_ups_en() we could end up looping for 10 seconds (20 ms * 500
loops). Add code similar to what's done in other places in the driver
to check for unplug and bail.

Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller

r8152: Check for unplug in rtl_phy_patch_request()

2023-10-22T10:46:18+00:00

If the adapter is unplugged while we're looping in
rtl_phy_patch_request() we could end up looping for 10 seconds (2 ms *
5000 loops). Add code similar to what's done in other places in the
driver to check for unplug and bail.

Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller

r8152: Release firmware if we have an error in probe

2023-10-22T10:46:18+00:00

The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().

Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller

r8152: Cancel hw_phy_work if we have an error in probe

2023-10-22T10:46:17+00:00

The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().

Fixes: a028a9e003f2 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson 
Reviewed-by: Grant Grundler 
Signed-off-by: David S. Miller