linux-stable.git/drivers/net, branch v5.6.18

Revert "net/mlx5: Annotate mutex destroy for root ns"

2020-06-10T18:22:53+00:00

This reverts commit 9b035b08e7e5fe7b2e75636324edf41ee30c5f94 which is
commit 9ca415399dae133b00273a4283ef31d003a6818d upstream.

It was backported incorrectly, Paul writes at:
	https://lore.kernel.org/r/20200607203425.GD23662@windriver.com

	I happened to notice this commit:

	9ca415399dae - "net/mlx5: Annotate mutex destroy for root ns"

	...was backported to 4.19 and 5.4 and v5.6 in linux-stable.

	It patches del_sw_root_ns() - which only exists after v5.7-rc7 from:

	6eb7a268a99b - "net/mlx5: Don't maintain a case of del_sw_func being
	null"

	which creates the one line del_sw_root_ns stub function around
	kfree(node) by breaking it out of tree_put_node().

	In the absense of del_sw_root_ns - the backport finds an identical one
	line kfree stub fcn - named del_sw_prio from this earlier commit:

	139ed6c6c46a - "net/mlx5: Fix steering memory leak"  [in v4.15-rc5]

	and then puts the mutex_destroy() into that (wrong) function, instead of
	putting it into tree_put_node where the root ns case used to be hand

Reported-by: Paul Gortmaker 
Cc: Roi Dayan 
Cc: Mark Bloch 
Cc: Saeed Mahameed 
Signed-off-by: Greg Kroah-Hartman

net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()

2020-06-10T18:22:49+00:00

[ Upstream commit a683012a8e77675a1947cc8f11f97cdc1d5bb769 ]

The drivers reports EINVAL to userspace through netlink on invalid meta
match. This is confusing since EINVAL is usually reserved for malformed
netlink messages. Replace it by more meaningful codes.

Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: Pablo Neira Ayuso 
Signed-off-by: Saeed Mahameed 
Signed-off-by: Greg Kroah-Hartman

net: dsa: felix: send VLANs on CPU port as egress-tagged

2020-06-10T18:22:49+00:00

[ Upstream commit 183be6f967fe37c3154bfac39e913c3bafe89d1b ]

As explained in other commits before (b9cd75e66895 and 87b0f983f66f),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.

But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:

bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16

(note that port 5 is the CPU port and not the front-panel swp0).

So this hardware will send all VLANs as tagged towards the CPU.

Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

nfp: flower: fix used time of merge flow statistics

2020-06-10T18:22:48+00:00

[ Upstream commit 5b186cd60f033110960a3db424ffbd6de4cee528 ]

Prior to this change the correct value for the used counter is calculated
but not stored nor, therefore, propagated to user-space. In use-cases such
as OVS use-case at least this results in active flows being removed from
the hardware datapath. Which results in both unnecessary flow tear-down
and setup, and packet processing on the host.

This patch addresses the problem by saving the calculated used value
which allows the value to propagate to user-space.

Found by inspection.

Fixes: aa6ce2ea0c93 ("nfp: flower: support stats update for merge flows")
Signed-off-by: Heinrich Kuhn 
Signed-off-by: Simon Horman 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: usb: qmi_wwan: add Telit LE910C1-EUX composition

2020-06-10T18:22:48+00:00

[ Upstream commit 591612aa578cd7148b7b9d74869ef40118978389 ]

Add support for Telit LE910C1-EUX composition

0x1031: tty, tty, tty, rmnet
Signed-off-by: Daniele Palmas 
Acked-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a

2020-06-10T18:22:48+00:00

[ Upstream commit f2fb6b6275eba9d312957ca44c487bd780da6169 ]

For rx filter 'HWTSTAMP_FILTER_PTP_V2_EVENT', it should be
PTP v2/802.AS1, any layer, any kind of event packet, but HW only
take timestamp snapshot for below PTP message: sync, Pdelay_req,
Pdelay_resp.

Then it causes below issue when test E2E case:
ptp4l[2479.534]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.423]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.758]: port 1: received DELAY_REQ without timestamp
ptp4l[2483.524]: port 1: received DELAY_REQ without timestamp
ptp4l[2484.233]: port 1: received DELAY_REQ without timestamp
ptp4l[2485.750]: port 1: received DELAY_REQ without timestamp
ptp4l[2486.888]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.265]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.316]: port 1: received DELAY_REQ without timestamp

Timestamp snapshot dependency on register bits in received path:
SNAPTYPSEL TSMSTRENA TSEVNTENA 	PTP_Messages
01         x         0          SYNC, Follow_Up, Delay_Req,
                                Delay_Resp, Pdelay_Req, Pdelay_Resp,
                                Pdelay_Resp_Follow_Up
01         0         1          SYNC, Pdelay_Req, Pdelay_Resp

For dwmac v5.10a, enabling all events by setting register
DWC_EQOS_TIME_STAMPING[SNAPTYPSEL] to 2’b01, clearing bit [TSEVNTENA]
to 0’b0, which can support all required events.

Signed-off-by: Fugang Duan 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5: Fix crash upon suspend/resume

2020-06-10T18:22:47+00:00

[ Upstream commit 8fc3e29be9248048f449793502c15af329f35c6e ]

Currently a Linux system with the mlx5 NIC always crashes upon
hibernation - suspend/resume.

Add basic callbacks so the NIC could be suspended and resumed.

Fixes: 9603b61de1ee ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Tested-by: Dexuan Cui 
Signed-off-by: Mark Bloch 
Reviewed-by: Moshe Shemesh 
Signed-off-by: Saeed Mahameed 
Signed-off-by: Greg Kroah-Hartman

airo: Fix read overflows sending packets

2020-06-07T11:16:49+00:00

commit 11e7a91994c29da96d847f676be023da6a2c1359 upstream.

The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.

The fix is to pad skb->data to at least ETH_ZLEN bytes.

Cc: 
Reported-by: Hu Jiahui 
Signed-off-by: Dan Carpenter 
Reviewed-by: Eric Dumazet 
Signed-off-by: Kalle Valo 
Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda
Signed-off-by: Greg Kroah-Hartman

net: dsa: mt7530: set CPU port to fallback mode

2020-06-07T11:16:49+00:00

commit 38152ea37d8bdaffa22603e0a5b5b86cfa8714c9 upstream.

Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:

	bridge vlan add dev br0 vid 2 pvid untagged self
	bridge vlan del dev br0 vid 1 self
	bridge vlan add dev sw0p0 vid 2 pvid untagged
	bridge vlan del dev sw0p0 vid 1
	# br0 cannot send untagged frames out of sw0p0 anymore

That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.

Set the CPU port to fallback mode so untagged frames can pass through.

Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

mt76: mt76x02u: Add support for newer versions of the XBox One wifi adapter

2020-06-07T11:16:48+00:00

commit b2934279c3e9719145ff4090d4ab951e340df17e upstream.

The current version has a new USB ID and reports as an 0x7632 device.
Adding the IDs results in it working out of the box.

Signed-off-by: Matthew Garrett 
Signed-off-by: Felix Fietkau 
Signed-off-by: Greg Kroah-Hartman