linux-stable.git/drivers/net, branch v5.4.80 Linux kernel stable tree can: m_can: process interrupt only when not runtime suspended 2020-11-24T12:29:18+00:00 Jarkko Nikula jarkko.nikula@linux.intel.com 2020-09-15T13:47:15+00:00 56588c1fdd19fbe6cd6c5cbd9ae3630279c574a2 [ Upstream commit a1f634463aaf2c94dfa13001dbdea011303124cc ] Avoid processing bogus interrupt statuses when the HW is runtime suspended and the M_CAN_IR register read may get all bits 1's. Handler can be called if the interrupt request is shared with other peripherals or at the end of free_irq(). Therefore check the runtime suspended status before processing. Fixes: cdf8259d6573 ("can: m_can: Add PM Support") Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a1f634463aaf2c94dfa13001dbdea011303124cc ]

Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().

Therefore check the runtime suspended status before processing.

Fixes: cdf8259d6573 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery 2020-11-24T12:29:18+00:00 Marc Kleine-Budde mkl@pengutronix.de 2020-11-18T15:01:48+00:00 a3c94201e0a752e7dd80de4c543a4a7d753292fa [ Upstream commit cd9f13c59461351d7a5fd07924264fb49b287359 ] If the CAN controller goes into bus off, the do_set_mode() callback with CAN_MODE_START can be used to recover the controller, which then calls flexcan_chip_start(). If configured, this is done automatically by the framework or manually by the user. In flexcan_chip_start() there is an explicit call to flexcan_transceiver_enable(), which does a regulator_enable() on the transceiver regulator. This results in a net usage counter increase, as there is no corresponding flexcan_transceiver_disable() in the bus off code path. This further leads to the transceiver stuck enabled, even if the CAN interface is shut down. To fix this problem the flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close(). Fixes: e955cead0311 ("CAN: Add Flexcan CAN controller driver") Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit cd9f13c59461351d7a5fd07924264fb49b287359 ]

If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.

In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.

To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().

Fixes: e955cead0311 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits 2020-11-24T12:29:17+00:00 Jimmy Assarsson extja@kvaser.com 2020-11-15T16:30:23+00:00 6d184f851182701dd8299d6eaedb936744b3e65e [ Upstream commit d003868d7f8579838ed58b6429af91844039b6f8 ] Use correct bittiming limits for the KCAN CAN controller. Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit d003868d7f8579838ed58b6429af91844039b6f8 ]

Use correct bittiming limits for the KCAN CAN controller.

Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: kvaser_pciefd: Fix KCAN bittiming limits 2020-11-24T12:29:08+00:00 Jimmy Assarsson extja@kvaser.com 2020-11-15T16:30:22+00:00 987bd7901ae397b144ffdb0dbcbab141fe278da6 [ Upstream commit 470e14c00c63752466ac44de392f584dfdddd82e ] Use correct bittiming limits for the KCAN CAN controller. Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20201115163027.16851-1-jimmyassarsson@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 470e14c00c63752466ac44de392f584dfdddd82e ]

Use correct bittiming limits for the KCAN CAN controller.

Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-1-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled 2020-11-24T12:29:07+00:00 Eli Cohen elic@nvidia.com 2020-11-09T09:35:52+00:00 401afa5f5e5eff9e4b70d9dea739b805a7bfb0e2 [ Upstream commit 5b8631c7b21ca8bc039f0bc030048973b039e0d2 ] Avoid calling mlx5_esw_modify_vport_rate() if qos is not enabled and avoid unnecessary syndrome messages from firmware. Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support") Signed-off-by: Eli Cohen <elic@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 5b8631c7b21ca8bc039f0bc030048973b039e0d2 ]

Avoid calling mlx5_esw_modify_vport_rate() if qos is not enabled and
avoid unnecessary syndrome messages from firmware.

Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: m_can: m_can_stop(): set device to software init mode before closing 2020-11-24T12:29:07+00:00 Faiz Abbas faiz_abbas@ti.com 2020-08-25T05:54:42+00:00 24ce39bf0aa28ca7e907ac8915ba735da5ae6205 [ Upstream commit a584e9bc1b7e88f24f8504886eafbe6c73d8a97c ] There might be some requests pending in the buffer when the interface close sequence occurs. In some devices, these pending requests might lead to the module not shutting down properly when m_can_clk_stop() is called. Therefore, move the device to init state before potentially powering it down. Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Dan Murphy <dmurphy@ti.com> Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a584e9bc1b7e88f24f8504886eafbe6c73d8a97c ]

There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.

Therefore, move the device to init state before potentially powering it down.

Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: m_can: m_can_class_free_dev(): introduce new function 2020-11-24T12:29:07+00:00 Dan Murphy dmurphy@ti.com 2020-02-27T18:38:29+00:00 db2f5579e725b15245b5052dad28e109d40cbf52 [ Upstream commit a8c22f5b0c689a29f45ef4a110d09fd391debcbc ] This patch creates a common function that peripherials can call to free the netdev device when failures occur. Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework") Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a8c22f5b0c689a29f45ef4a110d09fd391debcbc ]

This patch creates a common function that peripherials can call to free the
netdev device when failures occur.

Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: m_can: m_can_handle_state_change(): fix state change 2020-11-24T12:29:07+00:00 Wu Bo wubo.oduw@gmail.com 2020-01-29T02:23:30+00:00 9b0596c07da8cdfd4979c0e342bbcb19fbe74de0 [ Upstream commit cd0d83eab2e0c26fe87a10debfedbb23901853c1 ] m_can_handle_state_change() is called with the new_state as an argument. In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the following code indicate that a CAN_STATE_ERROR_WARNING is handled. This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING. Signed-off-by: Wu Bo <wubo.oduw@gmail.com> Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com Cc: Dan Murphy <dmurphy@ti.com> Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit cd0d83eab2e0c26fe87a10debfedbb23901853c1 ]

m_can_handle_state_change() is called with the new_state as an argument.

In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.

This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.

Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration 2020-11-24T12:29:07+00:00 Marc Kleine-Budde mkl@pengutronix.de 2020-08-10T20:23:49+00:00 69851481b342b274db1084299e29022d63431fc4 [ Upstream commit c81d0b6ca665477c761f227807010762630b089f ] Change the order in tcan4x5x_can_remove() to be the exact inverse of tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the device. Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c81d0b6ca665477c761f227807010762630b089f ]

Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.

Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init() 2020-11-24T12:29:06+00:00 Marc Kleine-Budde mkl@pengutronix.de 2020-01-03T10:30:34+00:00 d527bb8bd577f511a6096036cd3f3840a607efff [ Upstream commit 1ff203badbbf1738027c8395d5b40b0d462b6e4d ] This patch adds the missing error checking when initializing the regmap interface fails. Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 1ff203badbbf1738027c8395d5b40b0d462b6e4d ]

This patch adds the missing error checking when initializing the regmap
interface fails.

Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>