linux-stable.git/drivers/net, branch v5.4.136

net: bcmgenet: ensure EXT_ENERGY_DET_MASK is clear

2021-07-28T11:31:01+00:00

commit 5a3c680aa2c12c90c44af383fe6882a39875ab81 upstream.

Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.

Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger 
Acked-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: use correct .stats_set_histogram() on Topaz

2021-07-28T11:31:01+00:00

commit 11527f3c4725640e6c40a2b7654e303f45e82a6c upstream.

Commit 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
introduced wrong .stats_set_histogram() method for Topaz family.

The Peridot method should be used instead.

Signed-off-by: Marek Behún 
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

ixgbe: Fix packet corruption due to missing DMA sync

2021-07-28T11:31:01+00:00

commit 09cfae9f13d51700b0fecf591dcd658fc5375428 upstream.

When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.

The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.

Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.

Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme 
Tested-by: Tony Brelinski 
Signed-off-by: Tony Nguyen 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

r8169: Avoid duplicate sysfs entry creation error

2021-07-28T11:30:58+00:00

[ Upstream commit e9a72f874d5b95cef0765bafc56005a50f72c5fe ]

When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:

[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22

Add the segment number to the device name to make it more unique.

This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.

Fixes: f1e911d5d0dfd ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak 
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara 
Acked-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: hns3: fix rx VLAN offload state inconsistent issue

2021-07-28T11:30:57+00:00

[ Upstream commit bbfd4506f962e7e6fff8f37f017154a3c3791264 ]

Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.

Fixes it by enabling rx VLAN offload when VF initializing.

Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen 
Signed-off-by: Guangbin Huang 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: hisilicon: rename CACHE_LINE_MASK to avoid redefinition

2021-07-28T11:30:57+00:00

[ Upstream commit b16f3299ae1aa3c327e1fb742d0379ae4d6e86f2 ]

Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.

../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
  134 | #define CACHE_LINE_MASK   0x3F
In file included from ../include/linux/cache.h:6,
                 from ../include/linux/printk.h:9,
                 from ../include/linux/kernel.h:19,
                 from ../include/linux/list.h:9,
                 from ../include/linux/module.h:12,
                 from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
   17 | #define CACHE_LINE_MASK  (~(L1_CACHE_BYTES - 1))

Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap 
Cc: Vineet Gupta 
Cc: Jiangfeng Xiao 
Cc: "David S. Miller" 
Cc: Jakub Kicinski 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Check abort error state in bnxt_half_open_nic()

2021-07-28T11:30:57+00:00

[ Upstream commit 11a39259ff79b74bc99f8b7c44075a2d6d5e7ab1 ]

bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock.  Firmware reset can be happening at the same
time.  Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock.  It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting.  In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is.  The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.

Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:

  bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
  Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
  ...
  Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
  Call trace:
  bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
  bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
  bnxt_self_test+0x2dc/0x390 [bnxt_en]
  ethtool_self_test+0xe0/0x1f8
  dev_ethtool+0x1744/0x22d0
  dev_ioctl+0x190/0x3e0
  sock_ioctl+0x238/0x480
  do_vfs_ioctl+0xc4/0x758
  ksys_ioctl+0x84/0xb8
  __arm64_sys_ioctl+0x28/0x38
  el0_svc_handler+0xb0/0x180
  el0_svc+0x8/0xc

Fixes: a1301f08c5ac ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Add missing check for BNXT_STATE_ABORT_ERR in bnxt_fw_rset_task()

2021-07-28T11:30:57+00:00

[ Upstream commit 6cd657cb3ee6f4de57e635b126ffbe0e51d00f1a ]

In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock.  If the flag is set, we need to abort.

Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Refresh RoCE capabilities in bnxt_ulp_probe()

2021-07-28T11:30:57+00:00

[ Upstream commit 2c9f046bc377efd1f5e26e74817d5f96e9506c86 ]

The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.

Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur 
Reviewed-by: Edwin Peer 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Improve bnxt_ulp_stop()/bnxt_ulp_start() call sequence.

2021-07-28T11:30:56+00:00

[ Upstream commit aa46dffff452f7c6d907c4e6a0062e2c53a87fc0 ]

We call bnxt_ulp_stop() to notify the RDMA driver that some error or
imminent reset is about to happen.  After that we always call
some variants of bnxt_close().

In the next patch, we will integrate the recently added error
recovery with the RDMA driver.  In response to ulp_stop, the
RDMA driver may free MSIX vectors and that will also trigger
bnxt_close().  To avoid bnxt_close() from being called twice,
we set a new flag after ulp_stop is called.  If the RDMA driver
frees MSIX vectors while the new flag is set, we will not call
bnxt_close(), knowing that it will happen in due course.

With this change, we must make sure that the bnxt_close() call
after ulp_stop will reset IRQ.  Modify bnxt_reset_task()
accordingly if we call ulp_stop.

Signed-off-by: Vasundhara Volam 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin