linux-stable.git/drivers/net, branch v4.4.145 Linux kernel stable tree can: xilinx_can: fix RX overflow interrupt not being enabled 2018-07-28T05:45:04+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2018-02-26T12:27:13+00:00 264dc1588925388709eeddd51901042ca277c828 commit 83997997252f5d3fc7f04abc24a89600c2b504ab upstream. RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt() processes it. This means that an RX overflow interrupt will only be processed when another interrupt gets asserted (e.g. for RX/TX). Fix that by enabling the RXOFLW interrupt. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 83997997252f5d3fc7f04abc24a89600c2b504ab upstream.

RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).

Fix that by enabling the RXOFLW interrupt.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: xilinx_can: fix incorrect clear of non-processed interrupts 2018-07-28T05:45:04+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2018-02-26T12:39:59+00:00 f7efacee6f8aaa311726eed09470e970b59fd4e1 commit 2f4f0f338cf453bfcdbcf089e177c16f35f023c8 upstream. xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of them is asserted. This does not take into account that some of them could have been asserted between interrupt status read and interrupt clear, therefore clearing them without handling them. Fix the code to only clear those interrupts that it knows are asserted and therefore going to be processed in xcan_err_interrupt(). Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2f4f0f338cf453bfcdbcf089e177c16f35f023c8 upstream.

xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.

Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting 2018-07-28T05:45:03+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2017-02-23T12:50:03+00:00 e5df9264649e13f0b6c2da9ce089a8ac41ef5121 commit 620050d9c2be15c47017ba95efe59e0832e99a56 upstream. The xilinx_can driver assumes that the TXOK interrupt only clears after it has been acknowledged as many times as there have been successfully sent frames. However, the documentation does not mention such behavior, instead saying just that the interrupt is cleared when the clear bit is set. Similarly, testing seems to also suggest that it is immediately cleared regardless of the amount of frames having been sent. Performing some heavy TX load and then going back to idle has the tx_head drifting further away from tx_tail over time, steadily reducing the amount of frames the driver keeps in the TX FIFO (but not to zero, as the TXOK interrupt always frees up space for 1 frame from the driver's perspective, so frames continue to be sent) and delaying the local echo frames. The TX FIFO tracking is also otherwise buggy as it does not account for TX FIFO being cleared after software resets, causing BUG!, TX FIFO full when queue awake! messages to be output. There does not seem to be any way to accurately track the state of the TX FIFO for local echo support while using the full TX FIFO. The Zynq version of the HW (but not the soft-AXI version) has watermark programming support and with it an additional TX-FIFO-empty interrupt bit. Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used to detect whether 1 or 2 frames have been sent at interrupt processing time. Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode was also tested. An alternative way to solve this would be to drop local echo support but keep using the full TX FIFO. v2: Add FIFO space check before TX queue wake with locking to synchronize with queue stop. This avoids waking the queue when xmit() had just filled it. v3: Keep local echo support and reduce the amount of frames in FIFO instead as suggested by Marc Kleine-Budde. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 620050d9c2be15c47017ba95efe59e0832e99a56 upstream.

The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.

However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.

Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.

The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
  BUG!, TX FIFO full when queue awake!
messages to be output.

There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.

The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.

Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.

Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.

An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.

v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.

v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: xilinx_can: fix device dropping off bus on RX overrun 2018-07-28T05:45:03+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2017-02-07T11:23:04+00:00 d7dec444472632fcba1d4b3be0aac8d279a37cc4 commit 2574fe54515ed3487405de329e4e9f13d7098c10 upstream. The xilinx_can driver performs a software reset when an RX overrun is detected. This causes the device to enter Configuration mode where no messages are received or transmitted. The documentation does not mention any need to perform a reset on an RX overrun, and testing by inducing an RX overflow also indicated that the device continues to work just fine without a reset. Remove the software reset. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2574fe54515ed3487405de329e4e9f13d7098c10 upstream.

The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.

The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.

Remove the software reset.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: xilinx_can: fix recovery from error states not being propagated 2018-07-28T05:45:03+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2017-02-08T11:13:40+00:00 7e572a170fc30ce4e6bff79b2a54f445a88457ac commit 877e0b75947e2c7acf5624331bb17ceb093c98ae upstream. The xilinx_can driver contains no mechanism for propagating recovery from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE. Add such a mechanism by factoring the handling of XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of xcan_err_interrupt and checking for recovery after RX and TX if the interface is in one of those states. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 877e0b75947e2c7acf5624331bb17ceb093c98ae upstream.

The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.

Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: xilinx_can: fix RX loop if RXNEMP is asserted without RXOK 2018-07-28T05:45:03+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2017-02-07T15:01:14+00:00 e4c557649fda285e512f28a771038180cdeff6cf commit 32852c561bffd613d4ed7ec464b1e03e1b7b6c5c upstream. If the device gets into a state where RXNEMP (RX FIFO not empty) interrupt is asserted without RXOK (new frame received successfully) interrupt being asserted, xcan_rx_poll() will continue to try to clear RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is not empty, the interrupt will not be cleared and napi_schedule() will just be called again. This situation can occur when: (a) xcan_rx() returns without reading RX FIFO due to an error condition. The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear due to a frame still being in the FIFO. The frame will never be read from the FIFO as RXOK is no longer set. (b) A frame is received between xcan_rx_poll() reading interrupt status and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain set as the new message is still in the FIFO. I'm able to trigger case (b) by flooding the bus with frames under load. There does not seem to be any benefit in using both RXNEMP and RXOK in the way the driver does, and the polling example in the reference manual (UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either RXOK or RXNEMP can be used for detecting incoming messages. Fix the issue and simplify the RX processing by only using RXNEMP without RXOK. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 32852c561bffd613d4ed7ec464b1e03e1b7b6c5c upstream.

If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.

This situation can occur when:

(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.

(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.

I'm able to trigger case (b) by flooding the bus with frames under load.

There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.

Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper 2018-07-28T05:45:02+00:00 Jack Morgenstein jackm@dev.mellanox.co.il 2018-07-24T11:27:55+00:00 73dad08709fee646875f5a81c07b05fb54582732 [ Upstream commit 958c696f5a7274d9447a458ad7aa70719b29a50a ] Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp context, rather than the one passed in the input modifier. However, the qp number in the qp context is not defined as a required parameter by the FW. Therefore, drivers may choose to not specify the qp number in the qp context for the reset-to-init transition. Thus, we must save the qp number passed in the command input modifier -- which is always present. (This saved qp number is used as the input modifier for command 2RST_QP when a slave's qp's are destroyed). Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 958c696f5a7274d9447a458ad7aa70719b29a50a ]

Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.

However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.

Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).

Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tg3: Add higher cpu clock for 5762. 2018-07-25T08:18:17+00:00 Sanjeev Bansal sanjeevb.bansal@broadcom.com 2018-07-16T05:43:32+00:00 8a82aee2d2f349afbfaee3754af7cf40c16c16a8 [ Upstream commit 3a498606bb04af603a46ebde8296040b2de350d1 ] This patch has fix for TX timeout while running bi-directional traffic with 100 Mbps using 5762. Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 3a498606bb04af603a46ebde8296040b2de350d1 ]

This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.

Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: phy: fix flag masking in __set_phy_supported 2018-07-25T08:18:17+00:00 Heiner Kallweit hkallweit1@gmail.com 2018-07-03T20:34:54+00:00 92b0c8dd9ea76cf215b1f740d06f8de430326289 [ Upstream commit df8ed346d4a806a6eef2db5924285e839604b3f9 ] Currently also the pause flags are removed from phydev->supported because they're not included in PHY_DEFAULT_FEATURES. I don't think this is intended, especially when considering that this function can be called via phy_set_max_speed() anywhere in a driver. Change the masking to mask out only the values we're going to change. In addition remove the misleading comment, job of this small function is just to adjust the supported and advertised speeds. Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit df8ed346d4a806a6eef2db5924285e839604b3f9 ]

Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.

Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtlwifi: rtl8821ae: fix firmware is not ready to run 2018-07-22T12:25:53+00:00 Ping-Ke Shih pkshih@realtek.com 2018-06-28T02:02:27+00:00 99f303b36796f0b43da61434418975cd12fa0097 commit 9a98302de19991d51e067b88750585203b2a3ab6 upstream. Without this patch, firmware will not run properly on rtl8821ae, and it causes bad user experience. For example, bad connection performance with low rate, higher power consumption, and so on. rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and each firmware has firmware data buffer and size individually. Original code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and this mismatch causes firmware checksum error, then firmware can't start. In this situation, driver gives message "Firmware is not ready to run!". Fixes: fe89707f0afa ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware") Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Cc: Stable <stable@vger.kernel.org> # 4.0+ Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9a98302de19991d51e067b88750585203b2a3ab6 upstream.

Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.

rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.

In this situation, driver gives message "Firmware is not ready to run!".

Fixes: fe89707f0afa ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>