linux-stable.git/drivers/net, branch v4.3.5

team: Replace rcu_read_lock with a mutex in team_vlan_rx_kill_vid

2016-01-31T19:25:52+00:00

[ Upstream commit 60a6531bfe49555581ccd65f66a350cc5693fcde ]

We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.

Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko 
Signed-off-by: Ido Schimmel 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx5_core: Fix trimming down IRQ number

2016-01-31T19:25:52+00:00

[ Upstream commit 0b6e26ce89391327d955a756a7823272238eb867 ]

With several ConnectX-4 cards installed on a server, one may receive
irqn > 255 from the kernel API, which we mistakenly trim to 8bit.

This causes EQ creation failure with the following stack trace:
[] dump_stack+0x48/0x64
[] __setup_irq+0x3a1/0x4f0
[] request_threaded_irq+0x120/0x180
[] ? mlx5_eq_int+0x450/0x450 [mlx5_core]
[] mlx5_create_map_eq+0x1e4/0x2b0 [mlx5_core]
[] alloc_comp_eqs+0xb1/0x180 [mlx5_core]
[] mlx5_dev_init+0x5e9/0x6e0 [mlx5_core]
[] init_one+0x99/0x1c0 [mlx5_core]
[] local_pci_probe+0x4c/0xa0

Fixing it by changing of the irqn type from u8 to unsigned int to
support values > 255

Fixes: 61d0e73e0a5a ('net/mlx5_core: Use the the real irqn in eq->irqn')
Reported-by: Jiri Pirko 
Signed-off-by: Doron Tsur 
Signed-off-by: Matan Barak 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

ppp, slip: Validate VJ compression slot parameters completely

2016-01-31T19:25:51+00:00

[ Upstream commit 4ab42d78e37a294ac7bc56901d563c642e03c4ae ]

Currently slhc_init() treats out-of-range values of rslots and tslots
as equivalent to 0, except that if tslots is too large it will
dereference a null pointer (CVE-2015-7799).

Add a range-check at the top of the function and make it return an
ERR_PTR() on error instead of NULL.  Change the callers accordingly.

Compile-tested only.

Reported-by: 郭永刚 
References: http://article.gmane.org/gmane.comp.security.oss.general/17908
Signed-off-by: Ben Hutchings 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

dwc_eth_qos: Fix dma address for multi-fragment skbs

2016-01-31T19:25:51+00:00

[ Upstream commit d461873272169a3fc3a8d155d7b1c92e9d97b419 ]

The offset inside the fragment was not used for the dma address and
silent data corruption resulted because TSO makes the checksum match.

Fixes: 077742dac2c7 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS")
Signed-off-by: Lars Persson 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

bonding: Prevent IPv6 link local address on enslaved devices

2016-01-31T19:25:51+00:00

[ Upstream commit 03d84a5f83a67e692af00a3d3901e7820e3e84d5 ]

Commit 1f718f0f4f97 ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf80e15 ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened.  If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.

In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.

Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave")
Signed-off-by: Karl Heiss 
Signed-off-by: Jay Vosburgh 
Reviewed-by: Jarod Wilson 
Signed-off-by: Andy Gospodarek 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

vxlan: fix test which detect duplicate vxlan iface

2016-01-31T19:25:50+00:00

[ Upstream commit 07b9b37c227cb8d88d478b4a9c5634fee514ede1 ]

When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159dde, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.

Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10          DOWN           f2:55:1c:6a:fb:00 
vxlan11          DOWN           7a:cb:b9:38:59:0d 

Instead of checking sockets, let's loop over the vxlan iface list.

Fixes: 1c51a9159dde ("vxlan: fix race caused by dropping rtnl_unlock")
Reported-by: Thomas Faivre 
Signed-off-by: Nicolas Dichtel 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: cdc_ncm: avoid changing RX/TX buffers on MTU changes

2016-01-31T19:25:49+00:00

[ Upstream commit 1dfddff5fcd869fcab0c52fafae099dfa435a935 ]

NCM buffer sizes are negotiated with the device independently of
the network device MTU.  The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.

The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu.  And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size.  This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.

Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.

Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.

2016-01-31T19:25:49+00:00

[ Upstream commit ce8c839b74e3017996fad4e1b7ba2e2625ede82f ]

Packets that arrive from real hardware devices have ip_summed ==
CHECKSUM_UNNECESSARY if the hardware verified the checksums, or
CHECKSUM_NONE if the packet is bad or it was unable to verify it. The
current version of veth will replace CHECKSUM_NONE with
CHECKSUM_UNNECESSARY, which causes corrupt packets routed from hardware to
a veth device to be delivered to the application. This caused applications
at Twitter to receive corrupt data when network hardware was corrupting
packets.

We believe this was added as an optimization to skip computing and
verifying checksums for communication between containers. However, locally
generated packets have ip_summed == CHECKSUM_PARTIAL, so the code as
written does nothing for them. As far as we can tell, after removing this
code, these packets are transmitted from one stack to another unmodified
(tcpdump shows invalid checksums on both sides, as expected), and they are
delivered correctly to applications. We didn’t test every possible network
configuration, but we tried a few common ones such as bridging containers,
using NAT between the host and a container, and routing from hardware
devices to containers. We have effectively deployed this in production at
Twitter (by disabling RX checksum offloading on veth devices).

This code dates back to the first version of the driver, commit
 ("[NET]: Virtual ethernet device driver"), so I
suspect this bug occurred mostly because the driver API has evolved
significantly since then. Commit <0b7967503dc97864f283a> ("net/veth: Fix
packet checksumming") (in December 2010) fixed this for packets that get
created locally and sent to hardware devices, by not changing
CHECKSUM_PARTIAL. However, the same issue still occurs for packets coming
in from hardware devices.

Co-authored-by: Evan Jones 
Signed-off-by: Evan Jones 
Cc: Nicolas Dichtel 
Cc: Phil Sutter 
Cc: Toshiaki Makita 
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vijay Pandurangan 
Acked-by: Cong Wang 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

gianfar: Don't enable RX Filer if not supported

2016-01-23T04:55:50+00:00

[ Upstream commit 7bff47da1ee23d00d1257905f2944c29594f799d ]

After commit 15bf176db1fb ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176db1fb ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.

We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.

Reviewed-by: Chris Packham 
Reviewed-by: Mark Tomlinson 
Signed-off-by: Hamish Martin 
Reviewed-by: Claudiu Manoil 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

pptp: verify sockaddr_len in pptp_bind() and pptp_connect()

2016-01-23T04:55:48+00:00

[ Upstream commit 09ccfd238e5a0e670d8178cf50180ea81ae09ae1 ]

Reported-by: Dmitry Vyukov 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman