linux-stable.git/drivers/net, branch v3.16.76

caif-hsi: fix possible deadlock in cfhsi_exit_module()

2019-10-31T22:15:04+00:00

commit fdd258d49e88a9e0b49ef04a506a796f1c768a8e upstream.

cfhsi_exit_module() calls unregister_netdev() under rtnl_lock().
but unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.

Fixes: c41254006377 ("caif-hsi: Add rtnl support")
Signed-off-by: Taehee Yoo 
Signed-off-by: David S. Miller 
Signed-off-by: Ben Hutchings

bonding: validate ip header before check IPPROTO_IGMP

2019-10-31T22:15:02+00:00

commit 9d1bc24b52fb8c5d859f9a47084bf1179470e04c upstream.

bond_xmit_roundrobin() checks for IGMP packets but it parses
the IP header even before checking skb->protocol.

We should validate the IP header with pskb_may_pull() before
using iph->protocol.

Reported-and-tested-by: syzbot+e5be16aa39ad6e755391@syzkaller.appspotmail.com
Fixes: a2fd940f4cff ("bonding: fix broken multicast with round-robin mode")
Cc: Jay Vosburgh 
Cc: Veaceslav Falico 
Cc: Andy Gospodarek 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller 
[bwh: Backported to 3.16:
 - Keep using ACCESS_ONCE(), dev_kfree_skb_any(), …_can_tx()
 - Adjust context]
Signed-off-by: Ben Hutchings

carl9170: fix misuse of device driver API

2019-10-31T22:14:58+00:00

commit feb09b2933275a70917a869989ea2823e7356be8 upstream.

This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"

that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.

Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).

a summary from the changes (copied from the p54 patch):
 * Call usb_driver_release_interface() rather than
   device_release_driver().

 * Lock udev (the interface's parent) before unbinding the
   driver instead of locking udev->parent.

 * During the firmware loading process, take a reference
   to the USB interface instead of the USB device.

 * Don't take an unnecessary reference to the device during
   probe (and then don't drop it during disconnect).

and

 * Make sure to prevent use-after-free bugs by explicitly
   setting the driver context to NULL after signaling the
   completion.

Cc: Alan Stern 
Signed-off-by: Christian Lamparter 
Acked-by: Alan Stern 
Signed-off-by: Kalle Valo 
Signed-off-by: Ben Hutchings

mwifiex: fix 802.11n/WPA detection

2019-10-31T22:14:57+00:00

commit df612421fe2566654047769c6852ffae1a31df16 upstream.

Commit 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant
vendor IEs") adjusted the ieee_types_vendor_header struct, which
inadvertently messed up the offsets used in
mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring
mwifiex_is_rsn_oui_present().

As it stands, commit 63d7ef36103d breaks compatibility with WPA (not
WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is
not supported by AP" case in mwifiex_is_network_compatible().

Fixes: 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant vendor IEs")
Signed-off-by: Brian Norris 
Signed-off-by: Kalle Valo 
[bwh: Backported to 3.16: adjust filenames, context]
Signed-off-by: Ben Hutchings

mwifiex: Don't abort on small, spec-compliant vendor IEs

2019-10-31T22:14:57+00:00

commit 63d7ef36103d26f20325a921ecc96a3288560146 upstream.

Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.

Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.

While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.

Fixes: 685c9b7750bf ("mwifiex: Abort at too short BSS descriptor element")
Cc: Takashi Iwai 
Signed-off-by: Brian Norris 
Reviewed-by: Takashi Iwai 
Signed-off-by: Kalle Valo 
[bwh: Backported to 3.16: adjust filenames, context]
Signed-off-by: Ben Hutchings

bonding: Add vlan tx offload to hw_enc_features

2019-10-05T15:20:06+00:00

commit d595b03de2cb0bdf9bcdf35ff27840cc3a37158f upstream.

As commit 30d8177e8ac7 ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.

Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:

	 if (skb->encapsulation)
                 features &= dev->hw_enc_features;

clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8ac7 like this:

vlan_dev_hard_start_xmit
  -->dev_queue_xmit
    -->validate_xmit_skb
      -->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
      -->validate_xmit_vlan
        -->__vlan_hwaccel_push_inside //skb->tci is cleared
...
 --> bond_start_xmit
   --> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
     --> __skb_flow_dissect // nhoff point to IP header
        -->  case htons(ETH_P_8021Q)
             // skb_vlan_tag_present is false, so
             vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
             //vlan point to ip header wrongly

Fixes: b2a103e6d0af ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing 
Acked-by: Jay Vosburgh 
Signed-off-by: David S. Miller 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

bonding: Always enable vlan tx offload

2019-10-05T15:20:06+00:00

commit 30d8177e8ac776d89d387fad547af6a0f599210e upstream.

We build vlan on top of bonding interface, which vlan offload
is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is
BOND_XMIT_POLICY_ENCAP34.

Because vlan tx offload is off, vlan tci is cleared and skb push
the vlan header in validate_xmit_vlan() while sending from vlan
devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to
get information from protocol headers encapsulated within vlan,
because 'nhoff' is points to IP header, so bond hashing is based
on layer 2 info, which fails to distribute packets across slaves.

This patch always enable bonding's vlan tx offload, pass the vlan
packets to the slave devices with vlan tci, let them to handle
vlan implementation.

Fixes: 278339a42a1b ("bonding: propogate vlan_features to bonding master")
Suggested-by: Jiri Pirko 
Signed-off-by: YueHaibing 
Acked-by: Jiri Pirko 
Signed-off-by: David S. Miller 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

be2net: fix link failure after ethtool offline test

2019-10-05T15:20:04+00:00

commit 2e5db6eb3c23e5dc8171eb8f6af7a97ef9fcf3a9 upstream.

Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.

Changes in v2:
- added fixes header

Fixes: 4276e47e2d1c ("be2net: Add link test to list of ethtool self tests.")
Signed-off-by: Petr Oros 
Reviewed-by: Ivan Vecera 
Signed-off-by: David S. Miller 
Signed-off-by: Ben Hutchings

be2net: Fix number of Rx queues used for flow hashing

2019-10-05T15:20:00+00:00

commit 718f4a2537089ea41903bf357071306163bc7c04 upstream.

Number of Rx queues used for flow hashing returned by the driver is
incorrect and this bug prevents user to use the last Rx queue in
indirection table.

Let's say we have a NIC with 6 combined queues:

[root@sm-03 ~]# ethtool -l enp4s0f0
Channel parameters for enp4s0f0:
Pre-set maximums:
RX:             5
TX:             5
Other:          0
Combined:       6
Current hardware settings:
RX:             0
TX:             0
Other:          0
Combined:       6

Default indirection table maps all (6) queues equally but the driver
reports only 5 rings available.

[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 5 RX ring(s):
    0:      0     1     2     3     4     5     0     1
    8:      2     3     4     5     0     1     2     3
   16:      4     5     0     1     2     3     4     5
   24:      0     1     2     3     4     5     0     1
...

Now change indirection table somehow:

[root@sm-03 ~]# ethtool -X enp4s0f0 weight 1 1
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 6 RX ring(s):
    0:      0     0     0     0     0     0     0     0
...
   64:      1     1     1     1     1     1     1     1
...

Now it is not possible to change mapping back to equal (default) state:

[root@sm-03 ~]# ethtool -X enp4s0f0 equal 6
Cannot set RX flow hash configuration: Invalid argument

Fixes: 594ad54a2c3b ("be2net: Add support for setting and getting rx flow hash options")
Reported-by: Tianhao 
Signed-off-by: Ivan Vecera 
Signed-off-by: David S. Miller 
Signed-off-by: Ben Hutchings

can: flexcan: fix timeout when set small bitrate

2019-10-05T15:19:54+00:00

commit 247e5356a709eb49a0d95ff2a7f07dac05c8252c upstream.

Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):

| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000

A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.

| RTNETLINK answers: Connection timed out

It is caused by calling of flexcan_chip_unfreeze() timeout.

Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.

After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.

Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.

Signed-off-by: Joakim Zhang 
Reviewed-by: Dong Aisheng 
Signed-off-by: Marc Kleine-Budde 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings