linux-stable.git/drivers/net, branch v3.11.8 Linux kernel stable tree Revert "rt2x00pci: Use PCI MSIs whenever possible" 2013-11-13T03:08:08+00:00 Stanislaw Gruszka sgruszka@redhat.com 2013-09-23T02:08:13+00:00 e5804987902e8ab21459acd70217f889e06447d5 commit dfb6b7c109a7f98d324a759599d1b4616f02c79f upstream. This reverts commit 9483f40d8d01918b399b4e24d0c1111db0afffeb. Some devices stop to connect with above commit, see: https://bugzilla.kernel.org/show_bug.cgi?id=61621 Since there is no clear benefit of having MSI enabled, just revert change to fix the problem. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit dfb6b7c109a7f98d324a759599d1b4616f02c79f upstream.

This reverts commit 9483f40d8d01918b399b4e24d0c1111db0afffeb.

Some devices stop to connect with above commit, see:
https://bugzilla.kernel.org/show_bug.cgi?id=61621

Since there is no clear benefit of having MSI enabled, just revert
change to fix the problem.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: flexcan: flexcan_chip_start: fix regression, mark one MB for TX and abort pending TX 2013-11-13T03:08:08+00:00 Marc Kleine-Budde mkl@pengutronix.de 2013-10-04T08:52:36+00:00 96424f593af6d547c677b91d3570827895db51bf commit d5a7b406c529e4595ce03dc8f6dcf7fa36f106fa upstream. In patch 0d1862e can: flexcan: fix flexcan_chip_start() on imx6 the loop in flexcan_chip_start() that iterates over all mailboxes after the soft reset of the CAN core was removed. This loop put all mailboxes (even the ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63, this aborts any pending TX messages. After a cold boot there is random garbage in the mailboxes, which leads to spontaneous transmit of CAN frames during first activation. Further if the interface was disabled with a pending message (usually due to an error condition on the CAN bus), this message is retransmitted after enabling the interface again. This patch fixes the regression by: 1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX FIFO, 8 is used by TX. 2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that mailbox is aborted. Cc: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d5a7b406c529e4595ce03dc8f6dcf7fa36f106fa upstream.

In patch

    0d1862e can: flexcan: fix flexcan_chip_start() on imx6

the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.

After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.

This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.

Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: flexcan: fix mx28 detection by rearanging OF match table 2013-11-13T03:08:08+00:00 Marc Kleine-Budde mkl@pengutronix.de 2013-10-03T21:51:55+00:00 e7443e576411e4c16b63f68d979a605013b8f8c8 commit e358784297992b012e8071764d996191dd2b1a54 upstream. The current implemetation of of_match_device() relies that the of_device_id table in the driver is sorted from most specific to least specific compatible. Without this patch the mx28 is detected as the less specific p1010. This leads to a p1010 specific workaround is activated on the mx28, which is not needed. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e358784297992b012e8071764d996191dd2b1a54 upstream.

The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.

Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can: at91-can: fix device to driver data mapping for platform devices 2013-11-13T03:08:08+00:00 Marc Kleine-Budde mkl@pengutronix.de 2013-10-09T10:19:19+00:00 bf089b665ab4c8c27daed6259adaa90793970a3a commit 5abbeea553c8260ed4e2ac4aae962aff800b6c6d upstream. In commit: 3078cde7 can: at91_can: add dt support device tree support was added to the at91_can driver. In this commit the mapping of device to driver data was mixed up. This results in the sam9x5 parameters being used for the sam9263 and the workaround for the broken mailbox 0 on the sam9263 not being activated. This patch fixes the broken platform_device_id table. Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5abbeea553c8260ed4e2ac4aae962aff800b6c6d upstream.

In commit:

    3078cde7 can: at91_can: add dt support

device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.

This patch fixes the broken platform_device_id table.

Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwlwifi: pcie: add SKUs for 6000, 6005 and 6235 series 2013-11-13T03:08:08+00:00 Emmanuel Grumbach emmanuel.grumbach@intel.com 2013-09-24T16:34:26+00:00 f00f0f238a5e9624bd651f939a34b009cdb9dc9d commit 08a5dd3842f2ac61c6d69661d2d96022df8ae359 upstream. Add some new PCI IDs to the table for 6000, 6005 and 6235 series. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 08a5dd3842f2ac61c6d69661d2d96022df8ae359 upstream.

Add some new PCI IDs to the table for 6000, 6005 and 6235 series.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwlwifi: mvm: call ieee80211_scan_completed when needed 2013-11-13T03:08:07+00:00 Emmanuel Grumbach emmanuel.grumbach@intel.com 2013-09-15T11:39:02+00:00 cb59afeec59a06583359f685290ebb1eeff7a42e commit 5a3e9f7f8c8768b5f7df81100c684e4cd00a6eb5 upstream. When RFKill cuts short a scan, mac80211 cancels the scan. This is done by sending a host command to the firmware, but this command was dropped because of RFKill. Flag this command as "SEND_IN_RFKILL" to make sure it is sent to the firmware. The firmware will send SCAN_COMPLETE_NOTIFICATION which will trigger a call to ieee80211_scan_completed. If the scan cannot be aborted, it is because the firmware already finished the scan but we hadn't notified mac80211 at the time mac80211 decided to cancel the scan. By the time we see the scan could not be aborted, mac80211 has been notified already. This patch fixes situations in which we didn't notify mac80211 upon completion of the scan that was cut short by RFkill. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5a3e9f7f8c8768b5f7df81100c684e4cd00a6eb5 upstream.

When RFKill cuts short a scan, mac80211 cancels the scan.
This is done by sending a host command to the firmware, but
this command was dropped because of RFKill. Flag this
command as "SEND_IN_RFKILL" to make sure it is sent to the
firmware. The firmware will send SCAN_COMPLETE_NOTIFICATION
which will trigger a call to ieee80211_scan_completed.

If the scan cannot be aborted, it is because the firmware
already finished the scan but we hadn't notified mac80211
at the time mac80211 decided to cancel the scan. By the time
we see the scan could not be aborted, mac80211 has been
notified already.

This patch fixes situations in which we didn't notify
mac80211 upon completion of the scan that was cut short
by RFkill.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtlwifi: rtl8192cu: Fix error in pointer arithmetic 2013-11-13T03:08:07+00:00 Mark Cave-Ayland mark.cave-ayland@ilande.co.uk 2013-10-08T15:18:20+00:00 35a9611020cc8d42995c77e30db9e2e48ec831f0 commit 9473ca6e920a3b9ca902753ce52833657f9221cc upstream. An error in calculating the offset in an skb causes the driver to read essential device info from the wrong locations. The main effect is that automatic gain calculations are nonsense. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9473ca6e920a3b9ca902753ce52833657f9221cc upstream.

An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mwifiex: fix SDIO interrupt lost issue 2013-11-13T03:08:07+00:00 Amitkumar Karwar akarwar@marvell.com 2013-09-27T17:55:38+00:00 ecaa9a5393c6efea168c0092058a44e67c6ffa23 commit 453b0c3f6910672f79da354077af728d92f95c5b upstream. 601216e "mwifiex: process RX packets in SDIO IRQ thread directly" introduced a command timeout issue which can be reproduced easily on an AM33xx platform using a test application written by Daniel Mack: https://gist.github.com/zonque/6579314 mwifiex_main_process() is called from both the SDIO handler and the workqueue. In case an interrupt occurs right after the int_status check, but before updating the mwifiex_processing flag, this interrupt gets lost, resulting in a command timeout and consequently a card reset. Let main_proc_lock protect both int_status and mwifiex_processing flag. This fixes the interrupt lost issue. Reported-by: Sven Neumann <s.neumann@raumfeld.com> Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com> Tested-by: Daniel Mack <zonque@gmail.com> Reviewed-by: Dylan Reid <dgreid@chromium.org> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 453b0c3f6910672f79da354077af728d92f95c5b upstream.

601216e "mwifiex: process RX packets in SDIO IRQ thread directly"
introduced a command timeout issue which can be reproduced easily on
an AM33xx platform using a test application written by Daniel Mack:

https://gist.github.com/zonque/6579314

mwifiex_main_process() is called from both the SDIO handler and
the workqueue. In case an interrupt occurs right after the
int_status check, but before updating the mwifiex_processing flag,
this interrupt gets lost, resulting in a command timeout and
consequently a card reset.

Let main_proc_lock protect both int_status and mwifiex_processing
flag. This fixes the interrupt lost issue.

Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ath9k: fix tx queue scheduling after channel changes 2013-11-13T03:08:07+00:00 Felix Fietkau nbd@openwrt.org 2013-10-05T12:09:30+00:00 eca970de7c31574810e80ed780b8a661fc703213 commit ec30326ea773900da210c495e14cfeb532550ba2 upstream. Otherwise, if queues are full during a scan, tx scheduling does not resume after switching back to the home channel. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ec30326ea773900da210c495e14cfeb532550ba2 upstream.

Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wireless: cw1200: acquire hwbus lock around cw1200_irq_handler() call. 2013-11-04T12:35:21+00:00 Solomon Peachy pizza@shaftnet.org 2013-10-09T16:15:11+00:00 60fd01d9c7c5114e2bafaf5c57d2300aa9559c02 commit 4978705d26149a629b9f50ff221caed6f1ae3048 upstream. This fixes "lost interrupt" problems that occurred on SPI-based systems. cw1200_irq_handler() expects the hwbus to be locked, but on the SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the generic SDIO-code takes care of acquiring the lock). Signed-off-by: David Mosberger <davidm@egauge.net> Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 4978705d26149a629b9f50ff221caed6f1ae3048 upstream.

This fixes "lost interrupt" problems that occurred on SPI-based systems.
cw1200_irq_handler() expects the hwbus to be locked, but on the
SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the
generic SDIO-code takes care of acquiring the lock).

Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>