linux-stable.git/drivers/net, branch linux-5.18.y Linux kernel stable tree net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode 2022-08-17T12:42:35+00:00 Lukas Wunner lukas@wunner.de 2022-06-20T11:04:50+00:00 d7beed816f994319dd0e9c4a8d346f5408d4ba35 commit 2642cc6c3bbe0900ba15bab078fd15ad8baccbc5 upstream. Simon reports that if two LAN9514 USB adapters are directly connected without an intermediate switch, the link fails to come up and link LEDs remain dark. The issue was introduced by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling"). The PHY suffers from a known erratum wherein link detection becomes unreliable if Energy Detect Power-Down is used. In poll mode, the driver works around the erratum by briefly disabling EDPD for 640 msec to detect a neighbor, then re-enabling it to save power. In interrupt mode, no interrupt is signaled if EDPD is used by both link partners, so it must not be enabled at all. We'll recoup the power savings by enabling SUSPEND1 mode on affected LAN95xx chips in a forthcoming commit. Fixes: 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling") Reported-by: Simon Han <z.han@kunbus.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2642cc6c3bbe0900ba15bab078fd15ad8baccbc5 upstream.

Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark.  The issue was introduced by commit 1ce8b37241ed ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").

The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used.  In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.

In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.

We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.

Fixes: 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: dsa: felix: fix min gate len calculation for tc when its first gate is closed 2022-08-17T12:42:35+00:00 Vladimir Oltean vladimir.oltean@nxp.com 2022-08-04T20:28:17+00:00 38d22c3de8b8ba08263f4f94dbfc2b8622af3040 commit 7e4babffa6f340a74c820d44d44d16511e666424 upstream. min_gate_len[tc] is supposed to track the shortest interval of continuously open gates for a traffic class. For example, in the following case: TC 76543210 t0 00000001b 200000 ns t1 00000010b 200000 ns min_gate_len[0] and min_gate_len[1] should be 200000, while min_gate_len[2-7] should be 0. However what happens is that min_gate_len[0] is 200000, but min_gate_len[1] ends up being 0 (despite gate_len[1] being 200000 at the point where the logic detects the gate close event for TC 1). The problem is that the code considers a "gate close" event whenever it sees that there is a 0 for that TC (essentially it's level rather than edge triggered). By doing that, any time a gate is seen as closed without having been open prior, gate_len, which is 0, will be written into min_gate_len. Once min_gate_len becomes 0, it's impossible for it to track anything higher than that (the length of actually open intervals). To fix this, we make the writing to min_gate_len[tc] be edge-triggered, which avoids writes for gates that are closed in consecutive intervals. However what this does is it makes us need to special-case the permanently closed gates at the end. Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220804202817.1677572-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 7e4babffa6f340a74c820d44d44d16511e666424 upstream.

min_gate_len[tc] is supposed to track the shortest interval of
continuously open gates for a traffic class. For example, in the
following case:

TC 76543210

t0 00000001b 200000 ns
t1 00000010b 200000 ns

min_gate_len[0] and min_gate_len[1] should be 200000, while
min_gate_len[2-7] should be 0.

However what happens is that min_gate_len[0] is 200000, but
min_gate_len[1] ends up being 0 (despite gate_len[1] being 200000 at the
point where the logic detects the gate close event for TC 1).

The problem is that the code considers a "gate close" event whenever it
sees that there is a 0 for that TC (essentially it's level rather than
edge triggered). By doing that, any time a gate is seen as closed
without having been open prior, gate_len, which is 0, will be written
into min_gate_len. Once min_gate_len becomes 0, it's impossible for it
to track anything higher than that (the length of actually open
intervals).

To fix this, we make the writing to min_gate_len[tc] be edge-triggered,
which avoids writes for gates that are closed in consecutive intervals.
However what this does is it makes us need to special-case the
permanently closed gates at the end.

Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220804202817.1677572-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert "mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv" 2022-08-17T12:42:34+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2022-06-27T14:35:59+00:00 af504739ab57a19330d85213dd1770d703f6cc23 commit 5f8954e099b8ae96e7de1bb95950e00c85bedd40 upstream. This reverts commit a52ed4866d2b90dd5e4ae9dabd453f3ed8fa3cbc as it causes build problems in linux-next. It needs to be reintroduced in a way that can allow the api to evolve and not require a "flag day" to catch all users. Link: https://lore.kernel.org/r/20220623160723.7a44b573@canb.auug.org.au Cc: Duoming Zhou <duoming@zju.edu.cn> Cc: Brian Norris <briannorris@chromium.org> Cc: Johannes Berg <johannes@sipsolutions.net> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5f8954e099b8ae96e7de1bb95950e00c85bedd40 upstream.

This reverts commit a52ed4866d2b90dd5e4ae9dabd453f3ed8fa3cbc as it
causes build problems in linux-next.  It needs to be reintroduced in a
way that can allow the api to evolve and not require a "flag day" to
catch all users.

Link: https://lore.kernel.org/r/20220623160723.7a44b573@canb.auug.org.au
Cc: Duoming Zhou <duoming@zju.edu.cn>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbnet: smsc95xx: Fix deadlock on runtime resume 2022-08-17T12:42:21+00:00 Lukas Wunner lukas@wunner.de 2022-07-01T20:47:51+00:00 e81395cfbe62518f41af79a1b287fc8fe7c96b37 [ Upstream commit 7b960c967f2aa01ab8f45c5a0bd78e754cffdeee ] Commit 05b35e7eb9a1 ("smsc95xx: add phylib support") amended smsc95xx_resume() to call phy_init_hw(). That function waits for the device to runtime resume even though it is placed in the runtime resume path, causing a deadlock. The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(), which never uses the _nopm variant of usbnet_read_cmd(). Commit b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with reset operation") causes a similar deadlock on resume if the device was already runtime suspended when entering system sleep: That's because the commit introduced smsc95xx_reset_resume(), which calls down to smsc95xx_reset(), which neglects to use _nopm accessors. Fix by auto-detecting whether a device access is performed by the suspend/resume task_struct and use the _nopm variant if so. This works because the PM core guarantees that suspend/resume callbacks are run in task context. Stacktrace for posterity: INFO: task kworker/2:1:49 blocked for more than 122 seconds. Workqueue: usb_hub_wq hub_event schedule rpm_resume __pm_runtime_resume usb_autopm_get_interface usbnet_read_cmd __smsc95xx_read_reg __smsc95xx_phy_wait_not_busy __smsc95xx_mdio_read smsc95xx_mdiobus_read __mdiobus_read mdiobus_read smsc_phy_reset phy_init_hw smsc95xx_resume usb_resume_interface usb_resume_both usb_runtime_resume __rpm_callback rpm_callback rpm_resume __pm_runtime_resume usb_autoresume_device hub_event process_one_work Fixes: b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with reset operation") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.16+ Cc: Andre Edich <andre.edich@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7b960c967f2aa01ab8f45c5a0bd78e754cffdeee ]

Commit 05b35e7eb9a1 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw().  That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.

The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().

Commit b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:

That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.

Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so.  This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.

Stacktrace for posterity:

  INFO: task kworker/2:1:49 blocked for more than 122 seconds.
  Workqueue: usb_hub_wq hub_event
  schedule
  rpm_resume
  __pm_runtime_resume
  usb_autopm_get_interface
  usbnet_read_cmd
  __smsc95xx_read_reg
  __smsc95xx_phy_wait_not_busy
  __smsc95xx_mdio_read
  smsc95xx_mdiobus_read
  __mdiobus_read
  mdiobus_read
  smsc_phy_reset
  phy_init_hw
  smsc95xx_resume
  usb_resume_interface
  usb_resume_both
  usb_runtime_resume
  __rpm_callback
  rpm_callback
  rpm_resume
  __pm_runtime_resume
  usb_autoresume_device
  hub_event
  process_one_work

Fixes: b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling 2022-08-17T12:42:21+00:00 Lukas Wunner lukas@wunner.de 2022-05-12T08:42:05+00:00 7eea9a60703caf1b04eccba93cd103f1c8fc6809 [ Upstream commit 1ce8b37241ed291af56f7a49bbdbf20c08728e88 ] Link status of SMSC LAN95xx chips is polled once per second, even though they're capable of signaling PHY interrupts through the MAC layer. Forward those interrupts to the PHY driver to avoid polling. Benefits are reduced bus traffic, reduced CPU overhead and quicker interface bringup. Polling was introduced in 2016 by commit d69d16949346 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation"). Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt, hence couldn't detect link-up events when auto-negotiation was disabled. The proper solution would have been to enable the ENERGYON interrupt instead of polling. Since then, PHY handling was moved from the LAN95xx driver to the SMSC PHY driver with commit 05b35e7eb9a1 ("smsc95xx: add phylib support"). That PHY driver is capable of link detection with auto-negotiation disabled because it enables the ENERGYON interrupt. Note that signaling interrupts through the MAC layer not only works with the integrated PHY, but also with an external PHY, provided its interrupt pin is attached to LAN95xx's nPHY_INT pin. In the unlikely event that the interrupt pin of an external PHY is attached to a GPIO of the SoC (or not connected at all), the driver can be amended to retrieve the irq from the PHY's of_node. To forward PHY interrupts to phylib, it is not sufficient to call phy_mac_interrupt(). Instead, the PHY's interrupt handler needs to run so that PHY interrupts are cleared. That's because according to page 119 of the LAN950x datasheet, "The source of this interrupt is a level. The interrupt persists until it is cleared in the PHY." https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf Therefore, create an IRQ domain with a single IRQ for the PHY. In the future, the IRQ domain may be extended to support the 11 GPIOs on the LAN95xx. Normally the PHY interrupt should be masked until the PHY driver has cleared it. However masking requires a (sleeping) USB transaction and interrupts are received in (non-sleepable) softirq context. I decided not to mask the interrupt at all (by using the dummy_irq_chip's noop ->irq_mask() callback): The USB interrupt endpoint is polled in 1 msec intervals and normally that's sufficient to wake the PHY driver's IRQ thread and have it clear the interrupt. If it does take longer, worst thing that can happen is the IRQ thread is woken again. No big deal. Because PHY interrupts are now perpetually enabled, there's no need to selectively enable them on suspend. So remove all invocations of smsc95xx_enable_phy_wakeup_interrupts(). In smsc95xx_resume(), move the call of phy_init_hw() before usbnet_resume() (which restarts the status URB) to ensure that the PHY is fully initialized when an interrupt is handled. Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500 Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514 Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective Cc: Andre Edich <andre.edich@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 1ce8b37241ed291af56f7a49bbdbf20c08728e88 ]

Link status of SMSC LAN95xx chips is polled once per second, even though
they're capable of signaling PHY interrupts through the MAC layer.

Forward those interrupts to the PHY driver to avoid polling.  Benefits
are reduced bus traffic, reduced CPU overhead and quicker interface
bringup.

Polling was introduced in 2016 by commit d69d16949346 ("usbnet:
smsc95xx: fix link detection for disabled autonegotiation").
Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt,
hence couldn't detect link-up events when auto-negotiation was disabled.
The proper solution would have been to enable the ENERGYON interrupt
instead of polling.

Since then, PHY handling was moved from the LAN95xx driver to the SMSC
PHY driver with commit 05b35e7eb9a1 ("smsc95xx: add phylib support").
That PHY driver is capable of link detection with auto-negotiation
disabled because it enables the ENERGYON interrupt.

Note that signaling interrupts through the MAC layer not only works with
the integrated PHY, but also with an external PHY, provided its
interrupt pin is attached to LAN95xx's nPHY_INT pin.

In the unlikely event that the interrupt pin of an external PHY is
attached to a GPIO of the SoC (or not connected at all), the driver can
be amended to retrieve the irq from the PHY's of_node.

To forward PHY interrupts to phylib, it is not sufficient to call
phy_mac_interrupt().  Instead, the PHY's interrupt handler needs to run
so that PHY interrupts are cleared.  That's because according to page
119 of the LAN950x datasheet, "The source of this interrupt is a level.
The interrupt persists until it is cleared in the PHY."

https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf

Therefore, create an IRQ domain with a single IRQ for the PHY.  In the
future, the IRQ domain may be extended to support the 11 GPIOs on the
LAN95xx.

Normally the PHY interrupt should be masked until the PHY driver has
cleared it.  However masking requires a (sleeping) USB transaction and
interrupts are received in (non-sleepable) softirq context.  I decided
not to mask the interrupt at all (by using the dummy_irq_chip's noop
->irq_mask() callback):  The USB interrupt endpoint is polled in 1 msec
intervals and normally that's sufficient to wake the PHY driver's IRQ
thread and have it clear the interrupt.  If it does take longer, worst
thing that can happen is the IRQ thread is woken again.  No big deal.

Because PHY interrupts are now perpetually enabled, there's no need to
selectively enable them on suspend.  So remove all invocations of
smsc95xx_enable_phy_wakeup_interrupts().

In smsc95xx_resume(), move the call of phy_init_hw() before
usbnet_resume() (which restarts the status URB) to ensure that the PHY
is fully initialized when an interrupt is handled.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usbnet: smsc95xx: Avoid link settings race on interrupt reception 2022-08-17T12:42:21+00:00 Lukas Wunner lukas@wunner.de 2022-05-12T08:42:04+00:00 9b61971cab92a918cab7168d439a351b1c799aca [ Upstream commit 8960f878e39fadc03d74292a6731f1e914cf2019 ] When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the MAC full duplex mode and PHY flow control registers based on cached data in struct phy_device: smsc95xx_status() # raises EVENT_LINK_RESET usbnet_deferred_kevent() smsc95xx_link_reset() # uses cached data in phydev Simultaneously, phylib polls link status once per second and updates that cached data: phy_state_machine() phy_check_link_status() phy_read_status() lan87xx_read_status() genphy_read_status() # updates cached data in phydev If smsc95xx_link_reset() wins the race against genphy_read_status(), the registers may be updated based on stale data. E.g. if the link was previously down, phydev->duplex is set to DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even though genphy_read_status() may update it to DUPLEX_FULL afterwards. PHY interrupts are currently only enabled on suspend to trigger wakeup, so the impact of the race is limited, but we're about to enable them perpetually. Avoid the race by delaying execution of smsc95xx_link_reset() until phy_state_machine() has done its job and calls back via smsc95xx_handle_link_change(). Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib picks up link status changes through polling. So drop the declaration of a ->link_reset() callback. Note that the semicolon on a line by itself added in smsc95xx_status() is a placeholder for a function call which will be added in a subsequent commit. That function call will actually handle the INT_ENP_PHY_INT_ interrupt. Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500 Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514 Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 8960f878e39fadc03d74292a6731f1e914cf2019 ]

When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:

  smsc95xx_status()                 # raises EVENT_LINK_RESET
    usbnet_deferred_kevent()
      smsc95xx_link_reset()         # uses cached data in phydev

Simultaneously, phylib polls link status once per second and updates
that cached data:

  phy_state_machine()
    phy_check_link_status()
      phy_read_status()
        lan87xx_read_status()
          genphy_read_status()      # updates cached data in phydev

If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.

E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.

PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.

Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().

Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling.  So drop the declaration
of a ->link_reset() callback.

Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit.  That function call will actually handle the INT_ENP_PHY_INT_
interrupt.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usbnet: smsc95xx: Don't clear read-only PHY interrupt 2022-08-17T12:42:21+00:00 Lukas Wunner lukas@wunner.de 2022-05-12T08:42:02+00:00 ac057561b87ae5564d66f79d8e633753027d9811 [ Upstream commit 3108871f19221372b251f7da1ac38736928b5b3a ] Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver attempts to clear the signaled interrupts by writing "all ones" to the Interrupt Status Register. However the driver only ever enables a single type of interrupt, namely the PHY Interrupt. And according to page 119 of the LAN950x datasheet, its bit in the Interrupt Status Register is read-only. There's no other way to clear it than in a separate PHY register: https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf Consequently, writing "all ones" to the Interrupt Status Register is pointless and can be dropped. Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500 Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514 Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3108871f19221372b251f7da1ac38736928b5b3a ]

Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.

However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt.  And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only.  There's no other
way to clear it than in a separate PHY register:

https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf

Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net/ice: fix initializing the bitmap in the switch code 2022-08-17T12:42:02+00:00 Alexander Lobakin alexandr.lobakin@intel.com 2022-06-24T12:13:11+00:00 06b930278edf0f8580bf0ec7a5946fbb4b8178b9 [ Upstream commit 2f7ee2a72ccec8b85a05c4644d7ec9f40c1c50c8 ] Kbuild spotted the following bug during the testing of one of the optimizations: In file included from include/linux/cpumask.h:12, [...] from drivers/net/ethernet/intel/ice/ice_switch.c:4: drivers/net/ethernet/intel/ice/ice_switch.c: In function 'ice_find_free_recp_res_idx.constprop': include/linux/bitmap.h:447:22: warning: 'possible_idx[0]' is used uninitialized [-Wuninitialized] 447 | *map |= GENMASK(start + nbits - 1, start); | ^~ In file included from drivers/net/ethernet/intel/ice/ice.h:7, from drivers/net/ethernet/intel/ice/ice_lib.h:7, from drivers/net/ethernet/intel/ice/ice_switch.c:4: drivers/net/ethernet/intel/ice/ice_switch.c:4929:24: note: 'possible_idx[0]' was declared here 4929 | DECLARE_BITMAP(possible_idx, ICE_MAX_FV_WORDS); | ^~~~~~~~~~~~ include/linux/types.h:11:23: note: in definition of macro 'DECLARE_BITMAP' 11 | unsigned long name[BITS_TO_LONGS(bits)] | ^~~~ %ICE_MAX_FV_WORDS is 48, so bitmap_set() here was initializing only 48 bits, leaving a junk in the rest 16. It was previously hidden due to that filling 48 bits makes bitmap_set() call external __bitmap_set(), but after making it use plain bit arithmetics on small bitmaps, compilers started seeing the issue. It was still working because those 16 weren't used anywhere anyhow. bitmap_{clear,set}() are not really intended to initialize bitmaps, rather to modify already initialized ones, as they don't do anything past the passed number of bits. The correct function to do this in that particular case is bitmap_fill(), so use it here. It will do `*possible_idx = ~0UL` instead of `*possible_idx |= GENMASK(47, 0)`, not leaving anything in an undefined state. Fixes: fd2a6b71e300 ("ice: create advanced switch recipe") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Yury Norov <yury.norov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2f7ee2a72ccec8b85a05c4644d7ec9f40c1c50c8 ]

Kbuild spotted the following bug during the testing of one of
the optimizations:

In file included from include/linux/cpumask.h:12,
[...]
                from drivers/net/ethernet/intel/ice/ice_switch.c:4:
drivers/net/ethernet/intel/ice/ice_switch.c: In function 'ice_find_free_recp_res_idx.constprop':
include/linux/bitmap.h:447:22: warning: 'possible_idx[0]' is used uninitialized [-Wuninitialized]
  447 |                 *map |= GENMASK(start + nbits - 1, start);
      |                      ^~
In file included from drivers/net/ethernet/intel/ice/ice.h:7,
                 from drivers/net/ethernet/intel/ice/ice_lib.h:7,
                 from drivers/net/ethernet/intel/ice/ice_switch.c:4:
drivers/net/ethernet/intel/ice/ice_switch.c:4929:24: note: 'possible_idx[0]' was declared here
 4929 |         DECLARE_BITMAP(possible_idx, ICE_MAX_FV_WORDS);
      |                        ^~~~~~~~~~~~
include/linux/types.h:11:23: note: in definition of macro 'DECLARE_BITMAP'
   11 |         unsigned long name[BITS_TO_LONGS(bits)]
      |                       ^~~~

%ICE_MAX_FV_WORDS is 48, so bitmap_set() here was initializing only
48 bits, leaving a junk in the rest 16.
It was previously hidden due to that filling 48 bits makes
bitmap_set() call external __bitmap_set(), but after making it use
plain bit arithmetics on small bitmaps, compilers started seeing
the issue. It was still working because those 16 weren't used
anywhere anyhow.
bitmap_{clear,set}() are not really intended to initialize bitmaps,
rather to modify already initialized ones, as they don't do anything
past the passed number of bits. The correct function to do this in
that particular case is bitmap_fill(), so use it here. It will do
`*possible_idx = ~0UL` instead of `*possible_idx |= GENMASK(47, 0)`,
not leaving anything in an undefined state.

Fixes: fd2a6b71e300 ("ice: create advanced switch recipe")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net/mlx5: Expose mlx5_sriov_blocking_notifier_register / unregister APIs 2022-08-17T12:42:01+00:00 Yishai Hadas yishaih@nvidia.com 2022-05-10T09:02:03+00:00 8bfde97fb1fe2f1893014de526c34cf406377c22 [ Upstream commit 846e437387e74c44ddc9f3eeec472fd37ca3cdb9 ] Expose mlx5_sriov_blocking_notifier_register / unregister APIs to let a VF register to be notified for its enablement / disablement by the PF. Upon VF probe it will call mlx5_sriov_blocking_notifier_register() with its notifier block and upon VF remove it will call mlx5_sriov_blocking_notifier_unregister() to drop its registration. This can give a VF the ability to clean some resources upon disable before that the command interface goes down and on the other hand sets some stuff before that it's enabled. This may be used by a VF which is migration capable in few cases.(e.g. PF load/unload upon an health recovery). Link: https://lore.kernel.org/r/20220510090206.90374-2-yishaih@nvidia.com Signed-off-by: Yishai Hadas <yishaih@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 846e437387e74c44ddc9f3eeec472fd37ca3cdb9 ]

Expose mlx5_sriov_blocking_notifier_register / unregister APIs to let a
VF register to be notified for its enablement / disablement by the PF.

Upon VF probe it will call mlx5_sriov_blocking_notifier_register() with
its notifier block and upon VF remove it will call
mlx5_sriov_blocking_notifier_unregister() to drop its registration.

This can give a VF the ability to clean some resources upon disable
before that the command interface goes down and on the other hand sets
some stuff before that it's enabled.

This may be used by a VF which is migration capable in few cases.(e.g.
PF load/unload upon an health recovery).

Link: https://lore.kernel.org/r/20220510090206.90374-2-yishaih@nvidia.com
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv 2022-08-17T12:41:37+00:00 Duoming Zhou duoming@zju.edu.cn 2022-06-07T03:26:26+00:00 938139aef61bff52a154c68553fbaabd6924737f [ Upstream commit a52ed4866d2b90dd5e4ae9dabd453f3ed8fa3cbc ] There are sleep in atomic context bugs when uploading device dump data in mwifiex. The root cause is that dev_coredumpv could not be used in atomic contexts, because it calls dev_set_name which include operations that may sleep. The call tree shows execution paths that could lead to bugs: (Interrupt context) fw_dump_timer_fn mwifiex_upload_device_dump dev_coredumpv(..., GFP_KERNEL) dev_coredumpm() kzalloc(sizeof(*devcd), gfp); //may sleep dev_set_name kobject_set_name_vargs kvasprintf_const(GFP_KERNEL, ...); //may sleep kstrdup(s, GFP_KERNEL); //may sleep The corresponding fail log is shown below: [ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265 ... [ 135.293613] Call Trace: [ 135.293613] <IRQ> [ 135.293613] dump_stack_lvl+0x57/0x7d [ 135.293613] __might_resched.cold+0x138/0x173 [ 135.293613] ? dev_coredumpm+0xca/0x2e0 [ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] dev_coredumpm+0xca/0x2e0 [ 135.293613] ? devcd_freev+0x10/0x10 [ 135.293613] dev_coredumpv+0x1c/0x20 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] mwifiex_upload_device_dump+0x65/0xb0 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] call_timer_fn+0x122/0x3d0 [ 135.293613] ? msleep_interruptible+0xb0/0xb0 [ 135.293613] ? lock_downgrade+0x3c0/0x3c0 [ 135.293613] ? __next_timer_interrupt+0x13c/0x160 [ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] __run_timers.part.0+0x3f8/0x540 [ 135.293613] ? call_timer_fn+0x3d0/0x3d0 [ 135.293613] ? arch_restore_msi_irqs+0x10/0x10 [ 135.293613] ? lapic_next_event+0x31/0x40 [ 135.293613] run_timer_softirq+0x4f/0xb0 [ 135.293613] __do_softirq+0x1c2/0x651 ... [ 135.293613] RIP: 0010:default_idle+0xb/0x10 [ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246 [ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1 [ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20 [ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b [ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410 [ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2 ... [ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end This patch uses delayed work to replace timer and moves the operations that may sleep into a delayed work in order to mitigate bugs, it was tested on Marvell 88W8801 chip whose port is usb and the firmware is usb8801_uapsta.bin. The following is the result after using delayed work to replace timer. [ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end As we can see, there is no bug now. Fixes: f5ecd02a8b20 ("mwifiex: device dump support for usb interface") Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/b63b77fc84ed3e8a6bef02378e17c7c71a0bc3be.1654569290.git.duoming@zju.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a52ed4866d2b90dd5e4ae9dabd453f3ed8fa3cbc ]

There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:

   (Interrupt context)
fw_dump_timer_fn
  mwifiex_upload_device_dump
    dev_coredumpv(..., GFP_KERNEL)
      dev_coredumpm()
        kzalloc(sizeof(*devcd), gfp); //may sleep
        dev_set_name
          kobject_set_name_vargs
            kvasprintf_const(GFP_KERNEL, ...); //may sleep
            kstrdup(s, GFP_KERNEL); //may sleep

The corresponding fail log is shown below:

[  135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[  135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
...
[  135.293613] Call Trace:
[  135.293613]  <IRQ>
[  135.293613]  dump_stack_lvl+0x57/0x7d
[  135.293613]  __might_resched.cold+0x138/0x173
[  135.293613]  ? dev_coredumpm+0xca/0x2e0
[  135.293613]  kmem_cache_alloc_trace+0x189/0x1f0
[  135.293613]  ? devcd_match_failing+0x30/0x30
[  135.293613]  dev_coredumpm+0xca/0x2e0
[  135.293613]  ? devcd_freev+0x10/0x10
[  135.293613]  dev_coredumpv+0x1c/0x20
[  135.293613]  ? devcd_match_failing+0x30/0x30
[  135.293613]  mwifiex_upload_device_dump+0x65/0xb0
[  135.293613]  ? mwifiex_dnld_fw+0x1b0/0x1b0
[  135.293613]  call_timer_fn+0x122/0x3d0
[  135.293613]  ? msleep_interruptible+0xb0/0xb0
[  135.293613]  ? lock_downgrade+0x3c0/0x3c0
[  135.293613]  ? __next_timer_interrupt+0x13c/0x160
[  135.293613]  ? lockdep_hardirqs_on_prepare+0xe/0x220
[  135.293613]  ? mwifiex_dnld_fw+0x1b0/0x1b0
[  135.293613]  __run_timers.part.0+0x3f8/0x540
[  135.293613]  ? call_timer_fn+0x3d0/0x3d0
[  135.293613]  ? arch_restore_msi_irqs+0x10/0x10
[  135.293613]  ? lapic_next_event+0x31/0x40
[  135.293613]  run_timer_softirq+0x4f/0xb0
[  135.293613]  __do_softirq+0x1c2/0x651
...
[  135.293613] RIP: 0010:default_idle+0xb/0x10
[  135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246
[  135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1
[  135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20
[  135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b
[  135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410
[  135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2
...
[  135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end

This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.

[  134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[  135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end

As we can see, there is no bug now.

Fixes: f5ecd02a8b20 ("mwifiex: device dump support for usb interface")
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/b63b77fc84ed3e8a6bef02378e17c7c71a0bc3be.1654569290.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>