linux-stable.git/drivers/net/wireless, branch v4.4.159

ath10k: disable bundle mgmt tx completion event support

2018-09-19T20:48:58+00:00

[ Upstream commit 673bc519c55843c68c3aecff71a4101e79d28d2b ]

The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.

Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.

Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Signed-off-by: Surabhi Vishnoi 
Signed-off-by: Rakesh Pillai 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ath10k: prevent active scans on potential unusable channels

2018-09-19T20:48:57+00:00

[ Upstream commit 3f259111583801013cb605bb4414aa529adccf1c ]

The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.

Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.

ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.

Fixes: e8a50f8ba44b ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

brcmfmac: stop watchdog before detach and free everything

2018-08-24T11:26:56+00:00

[ Upstream commit 373c83a801f15b1e3d02d855fad89112bd4ccbe0 ]

Using built-in in kernel image without a firmware in filesystem
or in the kernel image can lead to a kernel NULL pointer deference.
Watchdog need to be stopped in brcmf_sdio_remove

The system is going down NOW!
[ 1348.110759] Unable to handle kernel NULL pointer dereference at virtual address 000002f8
Sent SIGTERM to all processes
[ 1348.121412] Mem abort info:
[ 1348.126962]   ESR = 0x96000004
[ 1348.130023]   Exception class = DABT (current EL), IL = 32 bits
[ 1348.135948]   SET = 0, FnV = 0
[ 1348.138997]   EA = 0, S1PTW = 0
[ 1348.142154] Data abort info:
[ 1348.145045]   ISV = 0, ISS = 0x00000004
[ 1348.148884]   CM = 0, WnR = 0
[ 1348.151861] user pgtable: 4k pages, 48-bit VAs, pgdp = (____ptrval____)
[ 1348.158475] [00000000000002f8] pgd=0000000000000000
[ 1348.163364] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 1348.168927] Modules linked in: ipv6
[ 1348.172421] CPU: 3 PID: 1421 Comm: brcmf_wdog/mmc0 Not tainted 4.17.0-rc5-next-20180517 #18
[ 1348.180757] Hardware name: Amarula A64-Relic (DT)
[ 1348.185455] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 1348.190251] pc : brcmf_sdiod_freezer_count+0x0/0x20
[ 1348.195124] lr : brcmf_sdio_watchdog_thread+0x64/0x290
[ 1348.200253] sp : ffff00000b85be30
[ 1348.203561] x29: ffff00000b85be30 x28: 0000000000000000
[ 1348.208868] x27: ffff00000b6cb918 x26: ffff80003b990638
[ 1348.214176] x25: ffff0000087b1a20 x24: ffff80003b94f800
[ 1348.219483] x23: ffff000008e620c8 x22: ffff000008f0b660
[ 1348.224790] x21: ffff000008c6a858 x20: 00000000fffffe00
[ 1348.230097] x19: ffff80003b94f800 x18: 0000000000000001
[ 1348.235404] x17: 0000ffffab2e8a74 x16: ffff0000080d7de8
[ 1348.240711] x15: 0000000000000000 x14: 0000000000000400
[ 1348.246018] x13: 0000000000000400 x12: 0000000000000001
[ 1348.251324] x11: 00000000000002c4 x10: 0000000000000a10
[ 1348.256631] x9 : ffff00000b85bc40 x8 : ffff80003be11870
[ 1348.261937] x7 : ffff80003dfc7308 x6 : 000000078ff08b55
[ 1348.267243] x5 : 00000139e1058400 x4 : 0000000000000000
[ 1348.272550] x3 : dead000000000100 x2 : 958f2788d6618100
[ 1348.277856] x1 : 00000000fffffe00 x0 : 0000000000000000

Signed-off-by: Michael Trimarchi 
Acked-by: Arend van Spriel 
Tested-by: Andy Shevchenko 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

rsi: Fix 'invalid vdd' warning in mmc

2018-08-06T14:24:38+00:00

[ Upstream commit 78e450719c702784e42af6da912d3692fd3da0cb ]

While performing cleanup, driver is messing with card->ocr
value by not masking rocr against ocr_avail. Below panic
is observed with some of the SDIO host controllers due to
this. Issue is resolved by reverting incorrect modifications
to vdd.

[  927.423821] mmc1: Invalid vdd 0x1f
[  927.423925] Modules linked in: rsi_sdio(+) cmac bnep arc4 rsi_91x
	       mac80211 cfg80211 btrsi rfcomm bluetooth ecdh_generic
[  927.424073] CPU: 0 PID: 1624 Comm: insmod Tainted: G		W        4.15.0-1000-caracalla #1
[  927.424075] Hardware name: Dell Inc. Edge Gateway	3003/      , BIOS 01.00.06 01/22/2018
[  927.424082] RIP: 0010:sdhci_set_power_noreg+0xdd/0x190[sdhci]
[  927.424085] RSP: 0018:ffffac3fc064b930 EFLAGS:  00010282
[  927.424107] Call Trace:
[  927.424118]  sdhci_set_power+0x5a/0x60 [sdhci]
[  927.424125]  sdhci_set_ios+0x360/0x3b0 [sdhci]
[  927.424133]  mmc_set_initial_state+0x92/0x120
[  927.424137]  mmc_power_up.part.34+0x33/0x1d0
[  927.424141]  mmc_power_up+0x17/0x20
[  927.424147]  mmc_sdio_runtime_resume+0x2d/0x50
[  927.424151]  mmc_runtime_resume+0x17/0x20
[  927.424156]  __rpm_callback+0xc4/0x200
[  927.424161]  ? idr_alloc_cyclic+0x57/0xd0
[  927.424165]  ? mmc_runtime_suspend+0x20/0x20
[  927.424169]  rpm_callback+0x24/0x80
[  927.424172]  ? mmc_runtime_suspend+0x20/0x20
[  927.424176]  rpm_resume+0x4b3/0x6c0
[  927.424181]  __pm_runtime_resume+0x4e/0x80
[  927.424188]  driver_probe_device+0x41/0x490
[  927.424192]  __driver_attach+0xdf/0xf0
[  927.424196]  ? driver_probe_device+0x490/0x490
[  927.424201]  bus_for_each_dev+0x6c/0xc0
[  927.424205]  driver_attach+0x1e/0x20
[  927.424209]  bus_add_driver+0x1f4/0x270
[  927.424217]  ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio]
[  927.424221]  driver_register+0x60/0xe0
[  927.424227]  ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio]
[  927.424231]  sdio_register_driver+0x20/0x30
[  927.424237]  rsi_module_init+0x16/0x40 [rsi_sdio]

Signed-off-by: Siva Rebbagondla 
Signed-off-by: Amitkumar Karwar 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

brcmfmac: Add support for bcm43364 wireless chipset

2018-08-06T14:24:36+00:00

[ Upstream commit 9c4a121e82634aa000a702c98cd6f05b27d6e186 ]

Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.

The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.

However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.

Signed-off-by: Sean Lanigan 
Acked-by: Ulf Hansson 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mwifiex: correct histogram data with appropriate index

2018-08-06T14:24:34+00:00

[ Upstream commit 30bfce0b63fa68c14ae1613eb9d259fa18644074 ]

Correct snr/nr/rssi data index to avoid possible buffer underflow.

Signed-off-by: Xinming Hu 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ath: Add regulatory mapping for Bahamas

2018-08-06T14:24:34+00:00

[ Upstream commit 699e2302c286a14afe7b7394151ce6c4e1790cc1 ]

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC

Signed-off-by: Sven Eckelmann 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ath: Add regulatory mapping for Bermuda

2018-08-06T14:24:34+00:00

[ Upstream commit 9c790f2d234f65697e3b0948adbfdf36dbe63dd7 ]

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: FCC
* 5GHz: FCC

Signed-off-by: Sven Eckelmann 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ath: Add regulatory mapping for Serbia

2018-08-06T14:24:33+00:00

[ Upstream commit 2a3169a54bb53717928392a04fb84deb765b51f1 ]

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: ETSI

Signed-off-by: Sven Eckelmann 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ath: Add regulatory mapping for Tanzania

2018-08-06T14:24:33+00:00

[ Upstream commit 667ddac5745fb9fddfe8f7fd2523070f50bd4442 ]

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC

Signed-off-by: Sven Eckelmann 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman