linux-stable.git/drivers/net/wireless, branch v4.19.7

brcmfmac: fix reporting support for 160 MHz channels

2018-12-01T08:37:26+00:00

commit d1fe6ad6f6bd61c84788d3a7b11e459a439c6169 upstream.

Driver can report IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ so it's
important to provide valid & complete info about supported bands for
each channel. By default no support for 160 MHz should be assumed unless
firmware reports it for a given channel later.

This fixes info passed to the userspace. Without that change userspace
could try to use invalid channel and fail to start an interface.

Signed-off-by: Rafał Miłecki 
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: don't use SAR Geo if basic SAR is not used

2018-12-01T08:37:26+00:00

commit 5d041c46ccb9b48acc110e214beff5e2789311df upstream.

We can't use SAR Geo if basic SAR is not enabled, since the SAR Geo
tables define offsets in relation to the basic SAR table in use.

To fix this, make iwl_mvm_sar_init() return one in case WRDS is not
available, so we can skip reading WGDS entirely.

Fixes: a6bff3cb19b7 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: fix regulatory domain update when the firmware starts

2018-12-01T08:37:26+00:00

commit 82715ac71e6b94a2c2136e31f3a8e6748e33aa8c upstream.

When the firmware starts, it doesn't have any regulatory
information, hence it uses the world wide limitations. The
driver can feed the firmware with previous knowledge that
was kept in the driver, but the firmware may still not
update its internal tables.

This happens when we start a BSS interface, and then the
firmware can change the regulatory tables based on our
location and it'll use more lenient, location specific
rules. Then, if the firmware is shut down (when the
interface is brought down), and then an AP interface is
created, the firmware will forget the country specific
rules.

The host will think that we are in a certain country that
may allow channels and will try to teach the firmware about
our location, but the firmware may still not allow to drop
the world wide limitations and apply country specific rules
because it was just re-started.

In this case, the firmware will reply with MCC_RESP_ILLEGAL
to the MCC_UPDATE_CMD. In that case, iwlwifi needs to let
the upper layers (cfg80211 / hostapd) know that the channel
list they know about has been updated.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201105

Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Luca Coelho 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: support sta_statistics() even on older firmware

2018-12-01T08:37:26+00:00

commit ec484d03ef0df8d34086b95710e355a259cbe1f2 upstream.

The oldest firmware supported by iwlmvm do support getting
the average beacon RSSI. Enable the sta_statistics() call
from mac80211 even on older firmware versions.

Fixes: 33cef9256342 ("iwlwifi: mvm: support beacon statistics for BSS client")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Luca Coelho 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE

2018-12-01T08:37:26+00:00

commit 66e839030fd698586734e017fd55c4f2a89dba0b upstream.

From coreboot/BIOS:
Name ("WGDS", Package() {
 Revision,
 Package() {
     DomainType,                         // 0x7:WiFi ==> We miss this one.
     WgdsWiFiSarDeltaGroup1PowerMax1,    // Group 1 FCC 2400 Max
     WgdsWiFiSarDeltaGroup1PowerChainA1, // Group 1 FCC 2400 A Offset
     WgdsWiFiSarDeltaGroup1PowerChainB1, // Group 1 FCC 2400 B Offset
     WgdsWiFiSarDeltaGroup1PowerMax2,    // Group 1 FCC 5200 Max
     WgdsWiFiSarDeltaGroup1PowerChainA2, // Group 1 FCC 5200 A Offset
     WgdsWiFiSarDeltaGroup1PowerChainB2, // Group 1 FCC 5200 B Offset
     WgdsWiFiSarDeltaGroup2PowerMax1,    // Group 2 EC Jap 2400 Max
     WgdsWiFiSarDeltaGroup2PowerChainA1, // Group 2 EC Jap 2400 A Offset
     WgdsWiFiSarDeltaGroup2PowerChainB1, // Group 2 EC Jap 2400 B Offset
     WgdsWiFiSarDeltaGroup2PowerMax2,    // Group 2 EC Jap 5200 Max
     WgdsWiFiSarDeltaGroup2PowerChainA2, // Group 2 EC Jap 5200 A Offset
     WgdsWiFiSarDeltaGroup2PowerChainB2, // Group 2 EC Jap 5200 B Offset
     WgdsWiFiSarDeltaGroup3PowerMax1,    // Group 3 ROW 2400 Max
     WgdsWiFiSarDeltaGroup3PowerChainA1, // Group 3 ROW 2400 A Offset
     WgdsWiFiSarDeltaGroup3PowerChainB1, // Group 3 ROW 2400 B Offset
     WgdsWiFiSarDeltaGroup3PowerMax2,    // Group 3 ROW 5200 Max
     WgdsWiFiSarDeltaGroup3PowerChainA2, // Group 3 ROW 5200 A Offset
     WgdsWiFiSarDeltaGroup3PowerChainB2, // Group 3 ROW 5200 B Offset
 }
})

When read the ACPI data to find out the WGDS, the DATA_SIZE is never
matched.
From the above format, it gives 19 numbers, but our driver is hardcode
as 18.
Fix it to pass then can parse the data into our wgds table.
Then we will see:
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init Sending GEO_TX_POWER_LIMIT
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[0]: chain A = 68 chain B = 69 max_tx_power = 54
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[1]: chain A = 48 chain B = 49 max_tx_power = 70
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[0]: chain A = 51 chain B = 67 max_tx_power = 50
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[1]: chain A = 69 chain B = 70 max_tx_power = 68
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[0]: chain A = 49 chain B = 50 max_tx_power = 48
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[1]: chain A = 52 chain B = 53 max_tx_power = 51

Cc: stable@vger.kernel.org # 4.12+
Fixes: a6bff3cb19b7 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Matt Chen 
Signed-off-by: Luca Coelho 
Signed-off-by: Greg Kroah-Hartman

mt76x0: run vco calibration for each channel configuration

2018-11-27T15:13:11+00:00

commit 473f0a763d2c7cd68a6dedf51e7d81e8f58f78ac upstream.

According to vendor sdk, vco calibration has to be executed
for each channel configuration whereas mcu calibration has to be
performed during channel scanning. This patch fixes the mt76x0
monitor mode issue since in that configuration vco calibration
was never executed

Fixes: 10de7a8b4ab9 ("mt76x0: phy files")
Tested-by: Sid Hayn 
Signed-off-by: Lorenzo Bianconi 
Signed-off-by: Felix Fietkau 
Cc: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: check return value of rs_rate_from_ucode_rate()

2018-11-13T19:08:41+00:00

commit 3d71c3f1f50cf309bd20659422af549bc784bfff upstream.

The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access.  This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659

Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho 
Signed-off-by: Kalle Valo 
Signed-off-by: Greg Kroah-Hartman

mt76: mt76x2: fix multi-interface beacon configuration

2018-11-13T19:08:41+00:00

commit 5289976ad887deb07c76df7eecf553c264aeebed upstream.

If the first virtual interface is a station (or an AP with beacons
temporarily disabled), the beacon of the second interface needs to
occupy hardware beacon slot 0.
For some reason the beacon index was incorrectly masked with the
virtual interface beacon mask, which prevents the secondary
interface from sending beacons unless the first one also does.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau 
Signed-off-by: Greg Kroah-Hartman

libertas: don't set URB_ZERO_PACKET on IN USB transfer

2018-11-13T19:08:41+00:00

commit 6528d88047801b80d2a5370ad46fb6eff2f509e0 upstream.

The USB core gets rightfully upset:

  usb 1-1: BOGUS urb flags, 240 --> 200
  WARNING: CPU: 0 PID: 60 at drivers/usb/core/urb.c:503 usb_submit_urb+0x2f8/0x3ed
  Modules linked in:
  CPU: 0 PID: 60 Comm: kworker/0:3 Not tainted 4.19.0-rc6-00319-g5206d00a45c7 #39
  Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
  Workqueue: events request_firmware_work_func
  EIP: usb_submit_urb+0x2f8/0x3ed
  Code: 75 06 8b 8f 80 00 00 00 8d 47 78 89 4d e4 89 55 e8 e8 35 1c f6 ff 8b 55 e8 56 52 8b 4d e4 51 50 68 e3 ce c7 c0 e8 ed 18 c6 ff <0f> 0b 83 c4 14 80 7d ef 01 74 0a 80 7d ef 03 0f 85 b8 00 00 00 8b
  EAX: 00000025 EBX: ce7d4980 ECX: 00000000 EDX: 00000001
  ESI: 00000200 EDI: ce7d8800 EBP: ce7f5ea8 ESP: ce7f5e70
  DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068 EFLAGS: 00210292
  CR0: 80050033 CR2: 00000000 CR3: 00e80000 CR4: 00000090
  Call Trace:
   ? if_usb_fw_timeo+0x64/0x64
   __if_usb_submit_rx_urb+0x85/0xe6
   ? if_usb_fw_timeo+0x64/0x64
   if_usb_submit_rx_urb_fwload+0xd/0xf
   if_usb_prog_firmware+0xc0/0x3db
   ? _request_firmware+0x54/0x47b
   ? _request_firmware+0x89/0x47b
   ? if_usb_probe+0x412/0x412
   lbs_fw_loaded+0x55/0xa6
   ? debug_smp_processor_id+0x12/0x14
   helper_firmware_cb+0x3c/0x3f
   request_firmware_work_func+0x37/0x6f
   process_one_work+0x164/0x25a
   worker_thread+0x1c4/0x284
   kthread+0xec/0xf1
   ? cancel_delayed_work_sync+0xf/0xf
   ? kthread_create_on_node+0x1a/0x1a
   ret_from_fork+0x2e/0x38
  ---[ end trace 3ef1e3b2dd53852f ]---

Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel 
Signed-off-by: Kalle Valo 
Signed-off-by: Greg Kroah-Hartman

ath10k: schedule hardware restart if WMI command times out

2018-11-13T19:08:30+00:00

[ Upstream commit a9911937e7d332761e8c4fcbc7ba0426bdc3956f ]

When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.

Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.

The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.

Signed-off-by: Martin Willi 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman