linux-stable.git/drivers/net/wireless, branch v3.2.36 Linux kernel stable tree iwlwifi: handle DMA mapping failures 2013-01-03T03:33:52+00:00 Johannes Berg johannes.berg@intel.com 2012-11-04T08:29:17+00:00 efd6621c748efd652b53ac6e718915bbbdca645e commit 7c34158231b2eda8dcbd297be2bb1559e69cb433 upstream. The RX replenish code doesn't handle DMA mapping failures, which will cause issues if there actually is a failure. This was reported by Shuah Khan who found a DMA mapping framework warning ("device driver failed to check map error"). Reported-by: Shuah Khan <shuah.khan@hp.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: - Adjust filename, context, indentation - Use bus(trans) instead of trans where necessary - Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7c34158231b2eda8dcbd297be2bb1559e69cb433 upstream.

The RX replenish code doesn't handle DMA mapping failures,
which will cause issues if there actually is a failure. This
was reported by Shuah Khan who found a DMA mapping framework
warning ("device driver failed to check map error").

Reported-by: Shuah Khan <shuah.khan@hp.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
 - Adjust filename, context, indentation
 - Use bus(trans) instead of trans where necessary
 - Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
iwlwifi: don't handle masked interrupt 2013-01-03T03:33:35+00:00 Emmanuel Grumbach emmanuel.grumbach@intel.com 2012-11-28T08:51:34+00:00 a4616d110b0de31d3ee0f447daf220be104aab42 commit 25a172655f837bdb032e451f95441bb4acec51bb upstream. This can lead to a panic if the driver isn't ready to handle them. Since our interrupt line is shared, we can get an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks that even when the interrupt is being freed). If the op_mode has gone away, we musn't call it. To avoid this the transport disables the interrupts when the hw is stopped and the op_mode is leaving. If there is an event that would cause an interrupt the INTA register is updated regardless of the enablement of the interrupts: even if the interrupts are disabled, the INTA will be changed, but the device won't issue an interrupt. But the ISR can be called at any time, so we ought ignore the value in the INTA otherwise we can call the op_mode after it was freed. I found this bug when the op_mode_start failed, and called iwl_trans_stop_hw(trans, true). Then I played with the RFKILL button, and removed the module. While removing the module, the IRQ is freed, and the ISR is called (CONFIG_DEBUG_SHIRQ enabled). Panic. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: - Adjust context - Pass bus(trans), not trans, to iwl_{read,write}32()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 25a172655f837bdb032e451f95441bb4acec51bb upstream.

This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).

If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.

I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
 - Adjust context
 - Pass bus(trans), not trans, to iwl_{read,write}32()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ath9k_hw: Fix signal strength / channel noise reporting 2013-01-03T03:33:33+00:00 Felix Fietkau nbd@openwrt.org 2012-12-10T13:03:17+00:00 f271af61a44cfe3d8c1b74ed4a7b9d79821026eb commit b7c0c238898d200e80487516e2b67aba2a522cc0 upstream. While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor for a chip measured in clean air, it refers to the lowest expected reading. Depending on the frequency, this measurement can vary by about 6db, thus causing a higher reported channel noise and signal strength. Factor in the 6db offset when converting internal noisefloor to channel noise. This patch makes the reported values more accurate for all chips without affecting NF calibration behavior. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit b7c0c238898d200e80487516e2b67aba2a522cc0 upstream.

While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.

Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.

Factor in the 6db offset when converting internal noisefloor to channel noise.

This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ath9k: ar9003: fix OTP register offsets for AR9340 2013-01-03T03:33:33+00:00 Gabor Juhos juhosg@openwrt.org 2012-12-09T22:57:09+00:00 97a93f6964202d8f25e8a2a284b66b5a2884d81e commit b3cd8021379306c0be6932e4d3b4b01efc681769 upstream. Trying to access the OTP memory on the AR9340 causes a data bus error like this: Data bus error, epc == 86e84164, ra == 86e84164 Oops[#1]: Cpu 0 $ 0 : 00000000 00000061 deadc0de 00000000 $ 4 : b8115f18 00015f18 00000007 00000004 $ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c $12 : 7c7c3c7c 001f0041 00000000 7c7c7c3c $16 : 86ee0000 00015f18 00000000 00000007 $20 : 00000004 00000064 00000004 86d71c44 $24 : 00000000 86e6ca00 $28 : 86d70000 86d71b20 86ece0c0 86e84164 Hi : 00000000 Lo : 00000064 epc : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw] Tainted: G O ra : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw] Status: 1100d403 KERNEL EXL IE Cause : 4080801c PrId : 0001974c (MIPS 74Kc) Modules linked in: ath9k(O+) ath9k_common(O) ath9k_hw(O) ath(O) ar934x_nfc mac80211(O) usbcore usb_common scsi_mod nls_base nand nand_ecc nand_ids crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crypto_blkcipher cryptomgr aead crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio Process insmod (pid: 459, threadinfo=86d70000, task=87942140, tls=779ac440) Stack : 802fb500 000200da 804db150 804e0000 87816130 86ee0000 00010000 86d71b88 86d71bc0 00000004 00000003 86e9fcd0 80305300 0002c0d0 86e74c50 800b4c20 000003e8 00000001 00000000 86ee0000 000003ff 86e9fd64 80305300 80123938 fffffffc 00000004 000058bc 00000000 86ea0000 86ee0000 000001ff 878d6000 99999999 86e9fdc0 86ee0fcc 86e9e664 0000c0d0 86ee0000 0000700000007000 ... Call Trace: [<86e84164>] ath9k_hw_wait+0x58/0xb0 [ath9k_hw] [<86e9fcd0>] ath9k_hw_setup_statusring+0x16b8/0x1c7c [ath9k_hw] Code: 0000a812 0040f809 00000000 <00531024> 1054000b 24020001 0c05b5dc 2404000a 26520001 The cause of the error is that the OTP register offsets are different on the AR9340 than the actually used values. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit b3cd8021379306c0be6932e4d3b4b01efc681769 upstream.

Trying to access the OTP memory on the AR9340
causes a data bus error like this:

  Data bus error, epc == 86e84164, ra == 86e84164
  Oops[#1]:
  Cpu 0
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 001f0041 00000000 7c7c7c3c
  $16   : 86ee0000 00015f18 00000000 00000007
  $20   : 00000004 00000064 00000004 86d71c44
  $24   : 00000000 86e6ca00
  $28   : 86d70000 86d71b20 86ece0c0 86e84164
  Hi    : 00000000
  Lo    : 00000064
  epc   : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
      Tainted: G           O
  ra    : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
  Status: 1100d403    KERNEL EXL IE
  Cause : 4080801c
  PrId  : 0001974c (MIPS 74Kc)
  Modules linked in: ath9k(O+) ath9k_common(O) ath9k_hw(O) ath(O) ar934x_nfc
  mac80211(O) usbcore usb_common scsi_mod nls_base nand nand_ecc nand_ids
  crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crypto_blkcipher cryptomgr
  aead crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio
  Process insmod (pid: 459, threadinfo=86d70000, task=87942140, tls=779ac440)
  Stack : 802fb500 000200da 804db150 804e0000 87816130 86ee0000 00010000 86d71b88
          86d71bc0 00000004 00000003 86e9fcd0 80305300 0002c0d0 86e74c50 800b4c20
          000003e8 00000001 00000000 86ee0000 000003ff 86e9fd64 80305300 80123938
          fffffffc 00000004 000058bc 00000000 86ea0000 86ee0000 000001ff 878d6000
          99999999 86e9fdc0 86ee0fcc 86e9e664 0000c0d0 86ee0000 0000700000007000
          ...
  Call Trace:
  [<86e84164>] ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
  [<86e9fcd0>] ath9k_hw_setup_statusring+0x16b8/0x1c7c [ath9k_hw]

  Code: 0000a812  0040f809  00000000 <00531024> 1054000b  24020001  0c05b5dc  2404000a  26520001

The cause of the error is that the OTP register
offsets are different on the AR9340 than the
actually used values.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Revert "ath9k_hw: Update AR9003 high_power tx gain table" 2013-01-03T03:33:32+00:00 Felix Fietkau nbd@openwrt.org 2012-12-06T17:40:11+00:00 c9d0bebf4f44ed7f28965207ead52460b1aee53b commit 9c170e068636deb3e3f96114034bb711675f0faa upstream. This reverts commit f74b9d365ddd33a375802b064f96a5d0e99af7c0. Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd "ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to bring the tx power back to normal levels on devices like the Buffalo WZR-HP-G450H, this one needs to be reverted as well. This revert improves tx power by ~10 db on that device Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 9c170e068636deb3e3f96114034bb711675f0faa upstream.

This reverts commit f74b9d365ddd33a375802b064f96a5d0e99af7c0.

Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.

This revert improves tx power by ~10 db on that device

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ath9k_hw: Enable hw PLL power save for AR9462 2013-01-03T03:32:58+00:00 Rajkumar Manoharan rmanohar@qca.qualcomm.com 2012-10-25T11:41:31+00:00 247a0b330ef3bb2e642d4bec5c04aee589733a4a commit 1680260226a8fd2aab590319da83ad8e610da9bd upstream. This reduced the power consumption to half in full and network sleep. Cc: Paul Stewart <pstew@chromium.org> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> [bwh: Backported to 3.2: - INIT_INI_ARRAY macro requires an explicit size argument - Remove the now-redundant macro PCIE_PLL_ON_CREQ_DIS_L1_2P0] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 1680260226a8fd2aab590319da83ad8e610da9bd upstream.

This reduced the power consumption to half in full and network sleep.

Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2:
 - INIT_INI_ARRAY macro requires an explicit size argument
 - Remove the now-redundant macro PCIE_PLL_ON_CREQ_DIS_L1_2P0]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mwifiex: report error to MMC core if we cannot suspend 2012-12-06T11:20:25+00:00 Bing Zhao bzhao@marvell.com 2012-11-15T23:58:48+00:00 e68f283495084cdf869400382fefab4aecccf7d2 commit dd321acddc3be1371263b8c9e6c6f2af89f63d57 upstream. When host_sleep_config command fails we should return error to MMC core to indicate the failure for our device. The misspelled variable is also removed as it's redundant. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit dd321acddc3be1371263b8c9e6c6f2af89f63d57 upstream.

When host_sleep_config command fails we should return error to
MMC core to indicate the failure for our device.

The misspelled variable is also removed as it's redundant.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mwifiex: fix system hang issue in cmd timeout error case 2012-12-06T11:20:24+00:00 Bing Zhao bzhao@marvell.com 2012-11-15T23:58:47+00:00 154fa8dc03e900f316a0267cbf45954c2f48a6e9 commit b1a47aa5e1e159e2cb06d7dfcc17ef5149b09299 upstream. Reported by Tim Shepard: I was seeing sporadic failures (wedgeups), and the majority of those failures I saw printed the printouts in mwifiex_cmd_timeout_func with cmd = 0xe5 which is CMD_802_11_HS_CFG_ENH. When this happens, two minutes later I get notified that the rtcwake thread is blocked, like this: INFO: task rtcwake:3495 blocked for more than 120 seconds. To get the hung thread unblocked we wake up the cmd wait queue and cancel the ioctl. Reported-by: Tim Shepard <shep@laptop.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit b1a47aa5e1e159e2cb06d7dfcc17ef5149b09299 upstream.

Reported by Tim Shepard:
I was seeing sporadic failures (wedgeups), and the majority of those
failures I saw printed the printouts in mwifiex_cmd_timeout_func with
cmd = 0xe5 which is CMD_802_11_HS_CFG_ENH.  When this happens, two
minutes later I get notified that the rtcwake thread is blocked, like
this:
      INFO: task rtcwake:3495 blocked for more than 120 seconds.

To get the hung thread unblocked we wake up the cmd wait queue and
cancel the ioctl.

Reported-by: Tim Shepard <shep@laptop.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
rtlwifi: rtl8192cu: Add new USB ID 2012-12-06T11:20:24+00:00 Albert Pool albertpool@solcon.nl 2012-10-30T19:58:06+00:00 8d61fa9bf394c53a4666c183f8d7a339e9c114bc commit a485e827f07bfdd0762059386e6e787bed6e81ee upstream. This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102. Its FCC ID is the same. Signed-off-by: Albert Pool <albertpool@solcon.nl> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a485e827f07bfdd0762059386e6e787bed6e81ee upstream.

This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102.
Its FCC ID is the same.

Signed-off-by: Albert Pool <albertpool@solcon.nl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
brcm80211: smac: only print block-ack timeout message at trace level 2012-12-06T11:20:16+00:00 Arend van Spriel arend@broadcom.com 2012-02-23T17:38:23+00:00 a30fc5988dd488e280fe8d3eb636e6fba00af139 commit 2b0a53d51b5f263bb581bbdb40ebb9f7e09609b1 upstream. In regular use block-ack timeouts can happen so it does not make sense to fill the log with these messages. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2b0a53d51b5f263bb581bbdb40ebb9f7e09609b1 upstream.

In regular use block-ack timeouts can happen so it does not make
sense to fill the log with these messages.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>