linux-stable.git/drivers/net/wireless, branch v3.12.41

iwlwifi: dvm: run INIT firmware again upon .start()

2015-04-22T06:58:33+00:00

commit 9c8928f5176766bec79f272bd47b7124e11cccbd upstream.

The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341

Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Jiri Slaby

ath5k: fix spontaneus AR5312 freezes

2015-03-16T13:58:21+00:00

commit 8bfae4f9938b6c1f033a5159febe97e441d6d526 upstream.

Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.

The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.

This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().

I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.

Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.

CC: Jiri Slaby 
CC: Nick Kossifidis 
CC: Luis R. Rodriguez 
Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux 
Tested-by: Christophe Prevotaux 
Tested-by: Eric Bree 
Signed-off-by: Sergey Ryazanov 
Signed-off-by: Kalle Valo 
Signed-off-by: Jiri Slaby

ath6kl: fix struct hif_scatter_req list handling

2015-03-05T14:37:13+00:00

commit 31b9cc9a873dcab161999622314f98a75d838975 upstream.

Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command:

iperf -c $TARGET_IP -i 5 -t 50 -w 1M

The crash was:

Unable to handle kernel paging request at virtual address 1a480000
pgd = 80004000
[1a480000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core]
CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1
Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio]
task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000
PC is at v7_dma_clean_range+0x20/0x38
LR is at dma_cache_maint_page+0x50/0x54
pc : [<8001a6f8>]    lr : [<800170fc>]    psr: 20000093
sp : dc9afcf8  ip : 8001a748  fp : 00000004
r10: 00000000  r9 : 00000001  r8 : 00000000
r7 : 00000001  r6 : 00000000  r5 : 80cb7000  r4 : 03f9a480
r3 : 0000001f  r2 : 00000020  r1 : 1a480000  r0 : 1a480000
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 6cc5004a  DAC: 00000015
Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238)
Stack: (0xdc9afcf8 to 0xdc9b0000)
fce0:                                                       80c9b29c 00000000
fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8
fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000
fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00
fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4
fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800
fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90
fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10
fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00
fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000
fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034
fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000
fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100
fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c
fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770
fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400
fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414
ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030
ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941
ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000
ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000
ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0
ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54)
[<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c)
[<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68)
[<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4)
[<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00)
[<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec)
[<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4)
[<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84)
[<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20)
[<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio])
[<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio])
[<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370)
[<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc)
[<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8)
[<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c)
Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a)
---[ end trace 0c038f0b8e0b67a3 ]---
Kernel panic - not syncing: Fatal exception

Jason's analysis:

  "The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead,
   it only run one round loop. This may be caused by that the GCC 4.8.1 thought
   that the scat_list only have one item and then no need to do full iteration,
   but this is simply wrong by looking at the assebly code. This will cause the sg
   buffer not get set when scat_entries > 1 and thus lead to kernel panic.

   Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)"

Fix this by using the normal [0] style for defining unknown number of list
entries following the struct. This also fixes corruption with scat_q_depth, which
was mistankely added to the end of struct and overwritten if there were more
than item in the scat list.

Reported-by: Jason Liu 
Tested-by: Jason Liu 
Signed-off-by: Kalle Valo 
Signed-off-by: Jiri Slaby

iwlwifi: mvm: always use mac color zero

2015-03-01T22:34:14+00:00

commit 5523d11cc46393a1e61b7ef4a0b2d4e7ed9521e4 upstream.

We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere.  In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.

Remove the color increment to use always zero and avoid reaching 255.

Signed-off-by: Luciano Coelho 
Reviewed-by: Johannes Berg 
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Jiri Slaby

iwlwifi: mvm: validate tid and sta_id in ba_notif

2015-03-01T22:34:14+00:00

commit 2cee4762c528a9bd2cdff793197bf591a2196c11 upstream.

These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.

Signed-off-by: Eyal Shapira 
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Jiri Slaby

iwlwifi: pcie: disable the SCD_BASE_ADDR when we resume from WoWLAN

2015-03-01T22:34:14+00:00

commit cd8f438405032ac8ff88bd8f2eca5e0c0063b14b upstream.

The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.

Reviewed-by: Johannes Berg 
Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Jiri Slaby

ath5k: fix hardware queue index assignment

2015-01-26T13:38:40+00:00

commit 9e4982f6a51a2442f1bb588fee42521b44b4531c upstream.

Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.

Signed-off-by: Felix Fietkau 
Signed-off-by: John W. Linville 
Signed-off-by: Jiri Slaby

ath9k: fix BE/BK queue order

2015-01-14T13:42:51+00:00

commit 78063d81d353e10cbdd279c490593113b8fdae1c upstream.

Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.

Signed-off-by: Felix Fietkau 
Signed-off-by: John W. Linville 
Signed-off-by: Jiri Slaby

ath9k_hw: fix hardware queue allocation

2015-01-14T13:42:51+00:00

commit ad8fdccf9c197a89e2d2fa78c453283dcc2c343f upstream.

The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.

Reported-by: Hubert Feurstein 
Signed-off-by: Felix Fietkau 
Signed-off-by: John W. Linville 
Signed-off-by: Jiri Slaby

rt2x00: do not align payload on modern H/W

2014-12-06T14:18:25+00:00

commit cfd9167af14eb4ec21517a32911d460083ee3d59 upstream.

RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.

For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.

Patch fixes skb_under_panic problems reported from time to time:

https://bugzilla.kernel.org/show_bug.cgi?id=84911
https://bugzilla.kernel.org/show_bug.cgi?id=72471
http://marc.info/?l=linux-wireless&m=139108549530402&w=2
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591

Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:

	if (payload_length && payload_align > header_align)
		header_align += 4;

but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).

Reported-and-tested-by: Antti S. Lankila 
Debugged-by: Antti S. Lankila 
Reported-by: Henrik Asp 
Originally-From: Helmut Schaa 
Signed-off-by: Stanislaw Gruszka 
Signed-off-by: John W. Linville 
Signed-off-by: Jiri Slaby