linux-stable.git/drivers/net/wireless, branch v3.1.3

rt2x00: Fix sleep-while-atomic bug in powersaving code.

2011-11-26T17:08:34+00:00

commit ed66ba472a742cd8df37d7072804b2111cdb1014 upstream.

The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.

Fix this by moving the call to rt2x00lib_config to a workqueue call.

This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672

Tested-by: Tomas Trnka 
Signed-off-by: Gertjan van Wingerde 
Acked-by: Ivo van Doorn 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

Net, libertas: Resolve memory leak in if_spi_host_to_card()

2011-11-26T17:08:34+00:00

commit fe09b32a4361bea44169b2063e8c867cabb6a8ba upstream.

If we hit the default case in the switch in if_spi_host_to_card() we'll leak
the memory we allocated for 'packet'. This patch resolves the leak by freeing
the allocated memory in that case.

Signed-off-by: Jesper Juhl 
Acked-by: Dan Williams 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

b43: refuse to load unsupported firmware

2011-11-21T22:35:24+00:00

[This patch is supposed to be applied in 3.1 (and maybe older) branches only.]

New kernels support newer firmware that users may try to incorrectly use
with older kernels. Display error and explain the problem in such a case

Signed-off-by: Rafał Miłecki 
Signed-off-by: Greg Kroah-Hartman

ath9k_hw: Fix regression of register offset for AR9003 chips

2011-11-11T17:44:48+00:00

commit 52d6d4ef5e6d1517688e27c11c01ab303ec681dd upstream.

My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.

This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message

ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.

Signed-off-by: Rajkumar Manoharan 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

ath9k_hw: Update AR9485 initvals to fix system hang issue

2011-11-11T17:44:44+00:00

commit 98fb2cc115b4ef1ea0a2d87a170c183bd395dd6c upstream.

This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.

Signed-off-by: Rajkumar Manoharan 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

iwlagn: do not use interruptible waits

2011-11-11T17:43:34+00:00

commit effd4d9aece9184f526e6556786a94d335e38b71 upstream.

Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.

This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.

Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.

This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in  'REPLY_SCAN_ABORT_CMD'

I have seen in P2P testing, but it is likely
that there are other errors caused by this.

Cc: Stanislaw Gruszka 
Signed-off-by: Johannes Berg 
Signed-off-by: Wey-Yi Guy 
Signed-off-by: John W. Linville

iwlagn: fix priv->cfg->ht_params NULL pointer dereference

2011-11-11T17:43:09+00:00

commit 107ef97a170dec95893f34614edd92eb8cb9b5d0 upstream.

This fix regression introduced by commit:

commit 15b3f3b006b42a678523cad989bfd60b76bf4403
Author: Wey-Yi Guy 
Date:   Fri Jun 3 07:54:13 2011 -0700

    iwlagn: set smps mode after assoc for 1000 device

Also remove unneeded brackets on the way.

Address:
https://bugzilla.redhat.com/show_bug.cgi?id=744155

Signed-off-by: Stanislaw Gruszka 
Acked-by: Wey-Yi Guy 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

wl12xx: fix forced passive scans

2011-11-11T17:43:09+00:00

commit 6cd9d21a0c1e2648c07c32c66bb25795ad3208aa upstream.

We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.

Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.

Signed-off-by: Luciano Coelho 
Signed-off-by: Greg Kroah-Hartman

ath9k: disable unnecessary PHY error reporting

2011-11-11T17:42:44+00:00

commit ac06697c79bad09e44a8b1d52104014016fb90de upstream.

PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.

Signed-off-by: Felix Fietkau 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

ath9k_hw: Fix number of GPIO pins for AR9287/9300

2011-11-11T17:42:44+00:00

commit 6321eb0977b011ac61dfca36e7c69b2c4325b104 upstream.

this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets

Signed-off-by: Mohammed Shafi Shajakhan 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman