linux-stable.git/drivers/net/wireless/intel, branch v5.4.178

iwlwifi: mvm: Increase the scan timeout guard to 30 seconds

2022-01-27T08:19:49+00:00

commit ced50f1133af12f7521bb777fcf4046ca908fb77 upstream.

With the introduction of 6GHz channels the scan guard timeout should
be adjusted to account for the following extreme case:

- All 6GHz channels are scanned passively: 58 channels.
- The scan is fragmented with the following parameters: 3 fragments,
  95 TUs suspend time, 44 TUs maximal out of channel time.

The above would result with scan time of more than 24 seconds. Thus,
set the timeout to 30 seconds.

Cc: stable@vger.kernel.org
Signed-off-by: Ilan Peer 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.3c851b93aef5.I346fa2e1d79220a6770496e773c6f87a2ad9e6c4@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: Fix calculation of frame length

2022-01-27T08:19:44+00:00

[ Upstream commit 40a0b38d7a7f91a6027287e0df54f5f547e8d27e ]

The RADA might include in the Rx frame the MIC and CRC bytes.
These bytes should be removed for non monitor interfaces and
should not be passed to mac80211.

Fix the Rx processing to remove the extra bytes on non monitor
cases.

Signed-off-by: Ilan Peer 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.098be12c801e.I1d81733d8a75b84c3b20eb6e0d14ab3405ca6a86@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: remove module loading failure message

2022-01-27T08:19:44+00:00

[ Upstream commit 6518f83ffa51131daaf439b66094f684da3fb0ae ]

When CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, iwlwifi crashes
when the opmode module cannot be loaded, due to completing
the completion before using drv->dev, which can then already
be freed.

Fix this by removing the (fairly useless) message. Moving the
completion later causes a deadlock instead, so that's not an
option.

Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/20211210091245.289008-2-luca@coelho.fi
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: fix leaks/bad data after failed firmware load

2022-01-27T08:19:44+00:00

[ Upstream commit ab07506b0454bea606095951e19e72c282bfbb42 ]

If firmware load fails after having loaded some parts of the
firmware, e.g. the IML image, then this would leak. For the
host command list we'd end up running into a WARN on the next
attempt to load another firmware image.

Fix this by calling iwl_dealloc_ucode() on failures, and make
that also clear the data so we start fresh on the next round.

Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20211210110539.1f742f0eb58a.I1315f22f6aa632d94ae2069f85e1bca5e734dce0@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: mvm: synchronize with FW after multicast commands

2022-01-27T08:19:42+00:00

[ Upstream commit db66abeea3aefed481391ecc564fb7b7fb31d742 ]

If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.

Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach 
Reported-by: Maximilian Ernestus 
Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: mvm: retry init flow if failed

2021-12-08T08:01:14+00:00

commit 5283dd677e52af9db6fe6ad11b2f12220d519d0c upstream.

In some very rare cases the init flow may fail.  In many cases, this is
recoverable, so we can retry.  Implement a loop to retry two more times
after the first attempt failed.

This can happen in two different situations, namely during probe and
during mac80211 start.  For the first case, a simple loop is enough.
For the second case, we need to add a flag to prevent mac80211 from
trying to restart it as well, leaving full control with the driver.

Cc: 
Signed-off-by: Mordechay Goodstein 
Signed-off-by: Luca Coelho 
Signed-off-by: Kalle Valo 
Link: https://lore.kernel.org/r/iwlwifi.20211110150132.57514296ecab.I52a0411774b700bdc7dedb124d8b59bf99456eb2@changeid
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: disable RX-diversity in powersave

2021-11-17T08:48:32+00:00

[ Upstream commit e5322b9ab5f63536c41301150b7ce64605ce52cc ]

Just like we have default SMPS mode as dynamic in powersave,
we should not enable RX-diversity in powersave, to reduce
power consumption when connected to a non-MIMO AP.

Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.fc896bc5cdaa.I1d11da71b8a5cbe921a37058d5f578f1b14a2023@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: mvm: fix access to BSS elements

2021-09-22T10:26:36+00:00

[ Upstream commit 6c608cd6962ebdf84fd3de6d42f88ed64d2f4e1b ]

BSS elements are protected using RCU, so we need to use
RCU properly to access them, fix that.

Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.fd8b5791ab44.Iba26800a6301078d3782fb249c476dd8ac2bf3c6@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin

iwlwifi: mvm: avoid static queue number aliasing

2021-09-22T10:26:36+00:00

[ Upstream commit c6ce1c74ef2923b8ffd85f7f8b486f804f343b39 ]

When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.

Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.

However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.

Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.

This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.

Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.

Signed-off-by: Johannes Berg
Signed-off-by: Luca Coelho
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho
Signed-off-by: Sasha Levin

iwlwifi: mvm: fix a memory leak in iwl_mvm_mac_ctxt_beacon_changed

2021-09-22T10:26:36+00:00

[ Upstream commit 0f5d44ac6e55551798dd3da0ff847c8df5990822 ]

If beacon_inject_active is true, we will return without freeing
beacon.  Fid that by freeing it before returning.

Signed-off-by: Zhang Qilong 
[reworded the commit message]
Signed-off-by: Luca Coelho 
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.d16206ca60fc.I9984a9b442c84814c307cee3213044e24d26f38a@changeid
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin