linux-stable.git/drivers/net/wan, branch v4.12

net: Fix inconsistent teardown and release of private netdev state.

2017-06-07T19:53:24+00:00

Network devices can allocate reasources and private memory using
netdev_ops->ndo_init().  However, the release of these resources
can occur in one of two different places.

Either netdev_ops->ndo_uninit() or netdev->destructor().

The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.

netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.

netdev->destructor(), on the other hand, does not run until the
netdev references all go away.

Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().

This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.

If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit().  But
it is not able to invoke netdev->destructor().

This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.

However, this means that the resources that would normally be released
by netdev->destructor() will not be.

Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.

Many drivers do not try to deal with this, and instead we have leaks.

Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().

netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().

netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().

Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().

And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().

Signed-off-by: David S. Miller

Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

2017-05-11T02:13:03+00:00

Pull hw lockdown support from David Howells:
 "Annotation of module parameters that configure hardware resources
  including ioports, iomem addresses, irq lines and dma channels.

  This allows a future patch to prohibit the use of such module
  parameters to prevent that hardware from being abused to gain access
  to the running kernel image as part of locking the kernel down under
  UEFI secure boot conditions.

  Annotations are made by changing:

        module_param(n, t, p)
        module_param_named(n, v, t, p)
        module_param_array(n, t, m, p)

  to:

        module_param_hw(n, t, hwtype, p)
        module_param_hw_named(n, v, t, hwtype, p)
        module_param_hw_array(n, t, hwtype, m, p)

  where the module parameter refers to a hardware setting

  hwtype specifies the type of the resource being configured. This can
  be one of:

        ioport          Module parameter configures an I/O port
        iomem           Module parameter configures an I/O mem address
        ioport_or_iomem Module parameter could be either (runtime set)
        irq             Module parameter configures an I/O port
        dma             Module parameter configures a DMA channel
        dma_addr        Module parameter configures a DMA buffer address
        other           Module parameter configures some other value

  Note that the hwtype is compile checked, but not currently stored (the
  lockdown code probably won't require it). It is, however, there for
  future use.

  A bonus is that the hwtype can also be used for grepping.

  The intention is for the kernel to ignore or reject attempts to set
  annotated module parameters if lockdown is enabled. This applies to
  options passed on the boot command line, passed to insmod/modprobe or
  direct twiddling in /sys/module/ parameter files.

  The module initialisation then needs to handle the parameter not being
  set, by (1) giving an error, (2) probing for a value or (3) using a
  reasonable default.

  What I can't do is just reject a module out of hand because it may
  take a hardware setting in the module parameters. Some important
  modules, some ipmi stuff for instance, both probe for hardware and
  allow hardware to be manually specified; if the driver is aborts with
  any error, you don't get any ipmi hardware.

  Further, trying to do this entirely in the module initialisation code
  doesn't protect against sysfs twiddling.

  [!] Note that in and of itself, this series of patches should have no
      effect on the the size of the kernel or code execution - that is
      left to a patch in the next series to effect. It does mark
      annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
      an already existing field"

* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
  Annotate hardware config module parameters in sound/pci/
  Annotate hardware config module parameters in sound/oss/
  Annotate hardware config module parameters in sound/isa/
  Annotate hardware config module parameters in sound/drivers/
  Annotate hardware config module parameters in fs/pstore/
  Annotate hardware config module parameters in drivers/watchdog/
  Annotate hardware config module parameters in drivers/video/
  Annotate hardware config module parameters in drivers/tty/
  Annotate hardware config module parameters in drivers/staging/vme/
  Annotate hardware config module parameters in drivers/staging/speakup/
  Annotate hardware config module parameters in drivers/staging/media/
  Annotate hardware config module parameters in drivers/scsi/
  Annotate hardware config module parameters in drivers/pcmcia/
  Annotate hardware config module parameters in drivers/pci/hotplug/
  Annotate hardware config module parameters in drivers/parport/
  Annotate hardware config module parameters in drivers/net/wireless/
  Annotate hardware config module parameters in drivers/net/wan/
  Annotate hardware config module parameters in drivers/net/irda/
  Annotate hardware config module parameters in drivers/net/hamradio/
  Annotate hardware config module parameters in drivers/net/ethernet/
  ...

wan: pc300too: abort path on failure

2017-04-24T19:51:31+00:00

In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.

Signed-off-by: Pan Bian 
Signed-off-by: David S. Miller

Annotate hardware config module parameters in drivers/net/wan/

2017-04-20T11:02:32+00:00

When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image.  Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.

To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify.  The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.

Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.

This patch annotates drivers in drivers/net/wan/.

Suggested-by: Alan Cox 
Signed-off-by: David Howells 
cc: "Jan \"Yenya\" Kasprzak" 
cc: netdev@vger.kernel.org

ucc/hdlc: fix two little issue

2017-03-14T04:53:48+00:00

1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register

Signed-off-by: Zhao Qiang 
Signed-off-by: David S. Miller

sched/headers: Prepare to move signal wakeup & sigpending methods from into

2017-03-02T07:42:32+00:00

Fix up affected files that include this signal functionality via sched.h.

Acked-by: Linus Torvalds 
Cc: Mike Galbraith 
Cc: Peter Zijlstra 
Cc: Thomas Gleixner 
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar

net/wan: add MODULE_LICENSE for fsl_ucc_hdlc

2017-02-17T20:20:43+00:00

It is required to build it as a module.

Signed-off-by: Valentin Longchamp 
Signed-off-by: David S. Miller

net: wan: slic_ds26522: Remove .owner field for driver

2017-02-07T16:41:15+00:00

Remove .owner field if calls are used which set it automatically.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

Signed-off-by: Wei Yongjun 
Signed-off-by: David S. Miller

net: wan: slic_ds26522: Use module_spi_driver to simplify the code

2017-02-07T16:41:15+00:00

module_spi_driver() makes the code simpler by eliminating
boilerplate code.

Signed-off-by: Wei Yongjun 
Signed-off-by: David S. Miller

drivers: net: generalize napi_complete_done()

2017-01-30T20:10:42+00:00

napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")

This allows for more efficient GRO aggregation without
sacrifying latencies.

Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller