[ Upstream commit 07b9b37c227cb8d88d478b4a9c5634fee514ede1 ]

When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159dde, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.

Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10          DOWN           f2:55:1c:6a:fb:00 <BROADCAST,MULTICAST>
vxlan11          DOWN           7a:cb:b9:38:59:0d <BROADCAST,MULTICAST>

Instead of checking sockets, let's loop over the vxlan iface list.

Fixes: 1c51a9159dde ("vxlan: fix race caused by dropping rtnl_unlock")
Reported-by: Thomas Faivre <thomas.faivre@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When looking for outer IP header, use the actual socket address family, not
the address family of the default destination which is not set for metadata
based interfaces (and doesn't have to match the address family of the
received packet even if it was set).

Fix also the misleading comment.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fill the metadata correctly even when tunneling over IPv6. Also, check that
the provided metadata is of an address family that is supported by the
tunnel.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will be used also for ndo_fill_metadata_dst.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv6/xfrm6_output.c
	net/openvswitch/flow_netlink.c
	net/openvswitch/vport-gre.c
	net/openvswitch/vport-vxlan.c
	net/openvswitch/vport.c
	net/openvswitch/vport.h

The openvswitch conflicts were overlapping changes.  One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.

The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.

Signed-off-by: David S. Miller <davem@davemloft.net>

While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices.  Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.

Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/usb/asix_common.c
	net/ipv4/inet_connection_sock.c
	net/switchdev/switchdev.c

In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.

The other two conflicts were overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>

Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.

An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.

CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

For metadata based vxlan interface, open both IPv4 and IPv6 socket. This is
much more user friendly: it's not necessary to create two vxlan interfaces
and pay attention to using the right one in routing rules.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make vxlan_sock_add both alloc the socket and attach it to vxlan_dev. Let
vxlan_sock_release accept vxlan_dev as its parameter instead of vxlan_sock.

This makes vxlan_sock_add and vxlan_sock release complementary. It reduces
code duplication in the next patch.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>