linux-stable.git/drivers/net/usb, branch v5.4.26 Linux kernel stable tree r8152: check disconnect status after long sleep 2020-03-18T06:17:41+00:00 You-Sheng Yang vicamo.yang@canonical.com 2020-02-26T15:37:10+00:00 d21ba36e4091676c378424fbe3b9c292e3af7fad [ Upstream commit d64c7a08034b32c285e576208ae44fc3ba3fa7df ] Dell USB Type C docking WD19/WD19DC attaches additional peripherals as: /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M |__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M |__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M |__ Port 4: Dev 13, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock. When hotplugging such dock with additional usb devices already attached on it, the probing process may reset usb 2.1 port, therefore r8152 ethernet device is also reset. However, during r8152 device init there are several for-loops that, when it's unable to retrieve hardware registers due to being disconnected from USB, may take up to 14 seconds each in practice, and that has to be completed before USB may re-enumerate devices on the bus. As a result, devices attached to the dock will only be available after nearly 1 minute after the dock was plugged in: [ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface [ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id [ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready [ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr [ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail This happens in, for example, r8153_init: static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size, void *data, u16 type) { if (test_bit(RTL8152_UNPLUG, &tp->flags)) return -ENODEV; ... } static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index) { u32 data; ... generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen); data = __le32_to_cpu(tmp); ... return (u16)data; } static void r8153_init(struct r8152 *tp) { ... if (test_bit(RTL8152_UNPLUG, &tp->flags)) return; for (i = 0; i < 500; i++) { if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) & AUTOLOAD_DONE) break; msleep(20); } ... } Since ocp_read_word() doesn't check the return status of generic_ocp_read(), and the only exit condition for the loop is to have a match in the returned value, such loops will only ends after exceeding its maximum runs when the device has been marked as disconnected, which takes 500 * 20ms = 10 seconds in theory, 14 in practice. To solve this long latency another test to RTL8152_UNPLUG flag should be added after those 20ms sleep to skip unnecessary loops, so that the device probe can complete early and proceed to parent port reset/reprobe process. This can be reproduced on all kernel versions up to latest v5.6-rc2, but after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less while it was around 1/2. Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit d64c7a08034b32c285e576208ae44fc3ba3fa7df ]

Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:

  /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
      |__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
          |__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
          |__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
              Driver=r8152, 5000M

where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.

When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:

  [ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
  [ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
  [ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
  [ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
  [ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail

This happens in, for example, r8153_init:

  static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
			    void *data, u16 type)
  {
    if (test_bit(RTL8152_UNPLUG, &tp->flags))
      return -ENODEV;
    ...
  }

  static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
  {
    u32 data;
    ...
    generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);

    data = __le32_to_cpu(tmp);
    ...
    return (u16)data;
  }

  static void r8153_init(struct r8152 *tp)
  {
    ...
    if (test_bit(RTL8152_UNPLUG, &tp->flags))
      return;

    for (i = 0; i < 500; i++) {
      if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
          AUTOLOAD_DONE)
        break;
      msleep(20);
    }
    ...
  }

Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.

To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.

This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.

Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qmi_wwan: unconditionally reject 2 ep interfaces 2020-03-05T15:43:37+00:00 Bjørn Mork bjorn@mork.no 2020-02-08T15:55:04+00:00 6eceafad2fffdce6fb227ad88f6e3cad36acfa4e [ Upstream commit 00516d13d4cfa56ce39da144db2dbf08b09b9357 ] We have been using the fact that the QMI and DIAG functions usually are the only ones with class/subclass/protocol being ff/ff/ff on Quectel modems. This has allowed us to match the QMI function without knowing the exact interface number, which can vary depending on firmware configuration. The ability to silently reject the DIAG function, which is usually handled by the option driver, is important for this method to work. This is done based on the knowledge that it has exactly 2 bulk endpoints. QMI function control interfaces will have either 3 or 1 endpoint. This rule is universal so the quirk condition can be removed. The fixed layouts known from the Gobi1k and Gobi2k modems have been gradually replaced by more dynamic layouts, and many vendors now use configurable layouts without changing device IDs. Renaming the class/subclass/protocol matching macro makes it more obvious that this is now not Quectel specific anymore. Cc: Kristian Evensen <kristian.evensen@gmail.com> Cc: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 00516d13d4cfa56ce39da144db2dbf08b09b9357 ]

We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.

The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work.  This is done based on the knowledge that it
has exactly 2 bulk endpoints.  QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.

The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs.  Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.

Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
qmi_wwan: re-add DW5821e pre-production variant 2020-03-05T15:43:37+00:00 Bjørn Mork bjorn@mork.no 2020-02-08T14:50:36+00:00 f5fe94e8dcfe06eb4efdc1bb8ae95f14daae0d71 [ Upstream commit 88bf54603f6f2c137dfee1abf6436ceac3528d2d ] Commit f25e1392fdb5 removed the support for the pre-production variant of the Dell DW5821e to avoid probing another USB interface unnecessarily. However, the pre-production samples are found in the wild, and this lack of support is causing problems for users of such samples. It is therefore necessary to support both variants. Matching on both interfaces 0 and 1 is not expected to cause any problem with either variant, as only the QMI function will be probed successfully on either. Interface 1 will be rejected based on the HID class for the production variant: T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2 P: Vendor=413c ProdID=81d7 Rev=03.18 S: Manufacturer=DELL S: Product=DW5821e Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option And interface 0 will be rejected based on too few endpoints for the pre-production variant: T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2 P: Vendor=413c ProdID=81d7 Rev= 3.18 S: Manufacturer=DELL S: Product=DW5821e Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver= I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware") Link: https://whrl.pl/Rf0vNk Reported-by: Lars Melin <larsm17@gmail.com> Cc: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 88bf54603f6f2c137dfee1abf6436ceac3528d2d ]

Commit f25e1392fdb5 removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples.  It is therefore
necessary to support both variants.

Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either.  Interface 1 will be rejected based on the HID class for the
production variant:

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

And interface 0 will be rejected based on too few endpoints for the
pre-production variant:

T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: disable DelayPhyPwrChg 2020-02-05T21:22:50+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:13+00:00 06b5e10871035d8125eb4aa07935cbecbc289490 [ Upstream commit aa475d935272481c9ffb1ae54eeca5c1819fbe1a ] When enabling this, the device would wait an internal signal which wouldn't be triggered. Then, the device couldn't enter P3 mode, so the power consumption is increased. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit aa475d935272481c9ffb1ae54eeca5c1819fbe1a ]

When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: avoid the MCU to clear the lanwake 2020-02-05T21:22:50+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:12+00:00 510818ae0f388d333bd5c1554fbcee2d2a2e3b1e [ Upstream commit 19813162895a696c5814d76e5f8fb6203d70f6e0 ] Avoid the MCU to clear the lanwake after suspending. It may cause the WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it and reset the lanwake status when resuming or initializing. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 19813162895a696c5814d76e5f8fb6203d70f6e0 ]

Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: disable test IO for RTL8153B 2020-02-05T21:22:50+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:10+00:00 3a128650b47aacded5867e46cad440a0cdf9cd41 [ Upstream commit d7f1b59655efb5a285d227c8f9853a98eab5c2fd ] For RTL8153B with QFN32, disable test IO. Otherwise, it may cause abnormal behavior for the device randomly. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit d7f1b59655efb5a285d227c8f9853a98eab5c2fd ]

For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: Disable PLA MCU clock speed down 2020-02-05T21:22:50+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:09+00:00 bc2ef2e9d1421d21faf2c5f1d30ce663ceb9a092 [ Upstream commit 08997b5eec08a2c29367f19a74abdea54b299406 ] PLA MCU clock speed down could only be enabled when tx/rx are disabled. Otherwise, the packet loss may occur. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 08997b5eec08a2c29367f19a74abdea54b299406 ]

PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: disable U2P3 for RTL8153B 2020-02-05T21:22:50+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:08+00:00 b05091c3ae99b68a93dce88b4c9b7f55c4ce8cd7 [ Upstream commit 809a7fc6593f288d6f820ef6cc57b9d69b5f9474 ] Enable U2P3 may miss zero packet for bulk-in. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 809a7fc6593f288d6f820ef6cc57b9d69b5f9474 ]

Enable U2P3 may miss zero packet for bulk-in.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
r8152: get default setting of WOL before initializing 2020-02-05T21:22:49+00:00 Hayes Wang hayeswang@realtek.com 2020-01-22T08:02:07+00:00 26a581fafceb7cddbabd9d08e679dc3b9d13578d [ Upstream commit 9583a3638dc07cc1878f41265e85ed497f72efcb ] Initailization would reset runtime suspend by tp->saved_wolopts, so the tp->saved_wolopts should be set before initializing. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 9583a3638dc07cc1878f41265e85ed497f72efcb ]

Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
qmi_wwan: Add support for Quectel RM500Q 2020-02-05T21:22:46+00:00 Kristian Evensen kristian.evensen@gmail.com 2020-01-13T13:57:40+00:00 e1133c1796a1e4fa413a773a5ecceb4c40f2258b [ Upstream commit a9ff44f0e61d074f29770413fef6a5452be7b83e ] RM500Q is a 5G module from Quectel, supporting both standalone and non-standalone modes. The normal Quectel quirks apply (DTR and dynamic interface numbers). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a9ff44f0e61d074f29770413fef6a5452be7b83e ]

RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>