linux-stable.git/drivers/net/usb, branch v4.14.331 Linux kernel stable tree r8152: Increase USB control msg timeout to 5000ms as per spec 2023-11-08T10:21:05+00:00 Douglas Anderson dianders@chromium.org 2023-10-20T21:06:52+00:00 6112a326fc272bd37b17c94bfc3a5594232f5706 [ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ] According to the comment next to USB_CTRL_GET_TIMEOUT and USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is usually quite fast, the spec allows them to take up to 5 seconds. Let's increase the timeout in the Realtek driver from 500ms to 5000ms (using the #defines) to account for this. This is not just a theoretical change. The need for the longer timeout was seen in testing. Specifically, if you drop a sc7180-trogdor based Chromebook into the kdb debugger and then "go" again after sitting in the debugger for a while, the next USB control message takes a long time. Out of ~40 tests the slowest USB control message was 4.5 seconds. While dropping into kdb is not exactly an end-user scenario, the above is similar to what could happen due to an temporary interrupt storm, what could happen if there was a host controller (HW or SW) issue, or what could happen if the Realtek device got into a confused state and needed time to recover. This change is fairly critical since the r8152 driver in Linux doesn't expect register reads/writes (which are backed by USB control messages) to fail. Fixes: ac718b69301c ("net/usb: new driver for RTL8152") Suggested-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ]

According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.

This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.

While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.

This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.

Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: usb: smsc95xx: Fix an error code in smsc95xx_reset() 2023-10-25T09:13:32+00:00 Dan Carpenter dan.carpenter@linaro.org 2023-10-16T17:28:10+00:00 7191c9a34b0700b606ed9a309a180c9295add43c commit c53647a5df9e66dd9fedf240198e1fe50d88c286 upstream. Return a negative error code instead of success. Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/147927f0-9ada-45cc-81ff-75a19dd30b76@moroto.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c53647a5df9e66dd9fedf240198e1fe50d88c286 upstream.

Return a negative error code instead of success.

Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/147927f0-9ada-45cc-81ff-75a19dd30b76@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read 2023-10-25T09:13:30+00:00 Javier Carrasco javier.carrasco.cruz@gmail.com 2023-10-09T22:26:14+00:00 b53b00bf71c6784adb529741dd0010d0abf3f27d commit 8f8abb863fa5a4cc18955c6a0e17af0ded3e4a76 upstream. syzbot has found an uninit-value bug triggered by the dm9601 driver [1]. This error happens because the variable res is not updated if the call to dm_read_shared_word returns an error. In this particular case -EPROTO was returned and res stayed uninitialized. This can be avoided by checking the return value of dm_read_shared_word and propagating the error if the read operation failed. [1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955 Cc: stable@vger.kernel.org Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com Acked-by: Peter Korsgaard <peter@korsgaard.com> Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver") Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8f8abb863fa5a4cc18955c6a0e17af0ded3e4a76 upstream.

syzbot has found an uninit-value bug triggered by the dm9601 driver [1].

This error happens because the variable res is not updated if the call
to dm_read_shared_word returns an error. In this particular case -EPROTO
was returned and res stayed uninitialized.

This can be avoided by checking the return value of dm_read_shared_word
and propagating the error if the read operation failed.

[1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955

Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver")
Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg 2023-10-10T19:43:41+00:00 Shigeru Yoshida syoshida@redhat.com 2023-09-23T17:35:49+00:00 3e0af6eec1789fd11934164a7f4dbcad979855a4 [ Upstream commit e9c65989920f7c28775ec4e0c11b483910fb67b8 ] syzbot reported the following uninit-value access issue: ===================================================== BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737 usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032 usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241 usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554 hub_port_connect drivers/usb/core/hub.c:5208 [inline] hub_port_connect_change drivers/usb/core/hub.c:5348 [inline] port_event drivers/usb/core/hub.c:5494 [inline] hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576 process_one_work+0x1688/0x2140 kernel/workqueue.c:2269 worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415 kthread+0x551/0x590 kernel/kthread.c:292 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293 Local variable ----buf.i87@smsc75xx_bind created at: __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 This issue is caused because usbnet_read_cmd() reads less bytes than requested (zero byte in the reproducer). In this case, 'buf' is not properly filled. This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads less bytes than requested. Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit e9c65989920f7c28775ec4e0c11b483910fb67b8 ]

syzbot reported the following uninit-value access issue:

=====================================================
BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x21c/0x280 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
 smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
 usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737
 usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374
 really_probe+0xf20/0x20b0 drivers/base/dd.c:529
 driver_probe_device+0x293/0x390 drivers/base/dd.c:701
 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
 usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032
 usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241
 usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272
 really_probe+0xf20/0x20b0 drivers/base/dd.c:529
 driver_probe_device+0x293/0x390 drivers/base/dd.c:701
 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
 usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554
 hub_port_connect drivers/usb/core/hub.c:5208 [inline]
 hub_port_connect_change drivers/usb/core/hub.c:5348 [inline]
 port_event drivers/usb/core/hub.c:5494 [inline]
 hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576
 process_one_work+0x1688/0x2140 kernel/workqueue.c:2269
 worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415
 kthread+0x551/0x590 kernel/kthread.c:292
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293

Local variable ----buf.i87@smsc75xx_bind created at:
 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
 smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
 smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482

This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.

This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.

Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: usb: qmi_wwan: add Quectel EM05GV2 2023-09-23T08:46:53+00:00 Martin Kohn m.kohn@welotec.com 2023-07-27T20:00:43+00:00 0bdeff71e72de707c1efd1a7761d35cc24d2b3ce [ Upstream commit d4480c9bb9258db9ddf2e632f6ef81e96b41089c ] Add support for Quectel EM05GV2 (G=global) with vendor ID 0x2c7c and product ID 0x030e Enabling DTR on this modem was necessary to ensure stable operation. Patch for usb: serial: option: is also in progress. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=030e Rev= 3.18 S: Manufacturer=Quectel S: Product=Quectel EM05-G C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Martin Kohn <m.kohn@welotec.com> Link: https://lore.kernel.org/r/AM0PR04MB57648219DE893EE04FA6CC759701A@AM0PR04MB5764.eurprd04.prod.outlook.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit d4480c9bb9258db9ddf2e632f6ef81e96b41089c ]

Add support for Quectel EM05GV2 (G=global) with vendor ID
0x2c7c and product ID 0x030e

Enabling DTR on this modem was necessary to ensure stable operation.
Patch for usb: serial: option: is also in progress.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030e Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Martin Kohn <m.kohn@welotec.com>
Link: https://lore.kernel.org/r/AM0PR04MB57648219DE893EE04FA6CC759701A@AM0PR04MB5764.eurprd04.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urb 2023-08-11T09:33:56+00:00 Alan Stern stern@rowland.harvard.edu 2023-07-12T14:15:10+00:00 a0715d04cf687a7e21f0d6ac8c1d479294a3f6f8 commit 5e1627cb43ddf1b24b92eb26f8d958a3f5676ccb upstream. The syzbot fuzzer identified a problem in the usbnet driver: usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Modules linked in: CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Workqueue: mld mld_ifc_work RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7 RSP: 0018:ffffc9000463f568 EFLAGS: 00010086 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001 RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003 R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500 FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0 Call Trace: <TASK> usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453 __netdev_start_xmit include/linux/netdevice.h:4918 [inline] netdev_start_xmit include/linux/netdevice.h:4932 [inline] xmit_one net/core/dev.c:3578 [inline] dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594 ... This bug is caused by the fact that usbnet trusts the bulk endpoint addresses its probe routine receives in the driver_info structure, and it does not check to see that these endpoints actually exist and have the expected type and directions. The fix is simply to add such a check. Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5e1627cb43ddf1b24b92eb26f8d958a3f5676ccb upstream.

The syzbot fuzzer identified a problem in the usbnet driver:

usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Workqueue: mld mld_ifc_work
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc9000463f568 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001
RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003
R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500
FS:  0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0
Call Trace:
 <TASK>
 usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453
 __netdev_start_xmit include/linux/netdevice.h:4918 [inline]
 netdev_start_xmit include/linux/netdevice.h:4932 [inline]
 xmit_one net/core/dev.c:3578 [inline]
 dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594
...

This bug is caused by the fact that usbnet trusts the bulk endpoint
addresses its probe routine receives in the driver_info structure, and
it does not check to see that these endpoints actually exist and have
the expected type and directions.

The fix is simply to add such a check.

Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: zaurus: Add ID for A-300/B-500/C-700 2023-08-11T09:33:56+00:00 Ross Maynard bids.7405@bigpond.com 2023-07-31T05:42:04+00:00 a0e677d7e3a68b9f3c5cd36054d6c1b7a2c23821 commit b99225b4fe297d07400f9e2332ecd7347b224f8d upstream. The SL-A300, B500/5600, and C700 devices no longer auto-load because of "usbnet: Remove over-broad module alias from zaurus." This patch adds IDs for those 3 devices. Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632 Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.") Signed-off-by: Ross Maynard <bids.7405@bigpond.com> Cc: stable@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b99225b4fe297d07400f9e2332ecd7347b224f8d upstream.

The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632
Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.")
Signed-off-by: Ross Maynard <bids.7405@bigpond.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: usb: qmi_wwan: add support for Compal RXM-G1 2023-06-21T13:38:58+00:00 Wes Huang wes.huang@moxa.com 2023-06-08T03:01:42+00:00 3a664de3ee85f4646c688a17679ce3ce8bc78e40 commit 863199199713908afaa47ba09332b87621c12496 upstream. Add support for Compal RXM-G1 which is based on Qualcomm SDX55 chip. This patch adds support for two compositions: 0x9091: DIAG + MODEM + QMI_RMNET + ADB 0x90db: DIAG + DUN + RMNET + DPL + QDSS(Trace) + ADB T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=9091 Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=90db Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms Cc: stable@vger.kernel.org Signed-off-by: Wes Huang <wes.huang@moxa.com> Acked-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20230608030141.3546-1-wes.huang@moxa.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 863199199713908afaa47ba09332b87621c12496 upstream.

Add support for Compal RXM-G1 which is based on Qualcomm SDX55 chip.
This patch adds support for two compositions:

0x9091: DIAG + MODEM + QMI_RMNET + ADB
0x90db: DIAG + DUN + RMNET + DPL + QDSS(Trace) + ADB

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=05c6 ProdID=9091 Rev= 4.14
S:  Manufacturer=QCOM
S:  Product=SDXPRAIRIE-MTP _SN:719AB680
S:  SerialNumber=719ab680
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=84(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=05c6 ProdID=90db Rev= 4.14
S:  Manufacturer=QCOM
S:  Product=SDXPRAIRIE-MTP _SN:719AB680
S:  SerialNumber=719ab680
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=84(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms

Cc: stable@vger.kernel.org
Signed-off-by: Wes Huang <wes.huang@moxa.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20230608030141.3546-1-wes.huang@moxa.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize 2023-06-09T08:22:55+00:00 Tudor Ambarus tudor.ambarus@linaro.org 2023-05-17T13:38:08+00:00 2334ff0b343ba6ba7a6c0586fcc83992bbbc1776 commit 7e01c7f7046efc2c7c192c3619db43292b98e997 upstream. Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than the calculated "min" value, but greater than zero, the logic sets tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in cdc_ncm_fill_tx_frame() where all the data is handled. For small values of dwNtbOutMaxSize the memory allocated during alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to how size is aligned at alloc time: size = SKB_DATA_ALIGN(size); size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info)); Thus we hit the same bug that we tried to squash with commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero") Low values of dwNtbOutMaxSize do not cause an issue presently because at alloc_skb() time more memory (512b) is allocated than required for the SKB headers alone (320b), leaving some space (512b - 320b = 192b) for CDC data (172b). However, if more elements (for example 3 x u64 = [24b]) were added to one of the SKB header structs, say 'struct skb_shared_info', increasing its original size (320b [320b aligned]) to something larger (344b [384b aligned]), then suddenly the CDC data (172b) no longer fits in the spare SKB data area (512b - 384b = 128b). Consequently the SKB bounds checking semantics fails and panics: skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:113! invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023 Workqueue: mld mld_ifc_work RIP: 0010:skb_panic net/core/skbuff.c:113 [inline] RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118 [snip] Call Trace: <TASK> skb_put+0x151/0x210 net/core/skbuff.c:2047 skb_put_zero include/linux/skbuff.h:2422 [inline] cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline] cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308 cdc_ncm_tx_fixup+0xa3/0x100 Deal with too low values of dwNtbOutMaxSize, clamp it in the range [USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure enough data space is allocated to handle CDC data by making sure dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE. Fixes: 289507d3364f ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning") Cc: stable@vger.kernel.org Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/ Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 7e01c7f7046efc2c7c192c3619db43292b98e997 upstream.

Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.

For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
	size = SKB_DATA_ALIGN(size);
        size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")

Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).

However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).

Consequently the SKB bounds checking semantics fails and panics:

skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
 <TASK>
 skb_put+0x151/0x210 net/core/skbuff.c:2047
 skb_put_zero include/linux/skbuff.h:2422 [inline]
 cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
 cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
 cdc_ncm_tx_fixup+0xa3/0x100

Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.

Fixes: 289507d3364f ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdc_ncm: Fix the build warning 2023-06-09T08:22:55+00:00 Alexander Bersenev bay@hackerdom.ru 2020-03-14T05:33:24+00:00 47473722d2754621cf8588db0cd3d4720e66d206 commit 5d0ab06b63fc9c727a7bb72c81321c0114be540b upstream. The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16. Fixes: 0fa81b304a79 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block") Signed-off-by: Alexander Bersenev <bay@hackerdom.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5d0ab06b63fc9c727a7bb72c81321c0114be540b upstream.

The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.

Fixes: 0fa81b304a79 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>