linux-stable.git/drivers/net/sky2.c, branch linux-2.6.26.y

sky2: 88E8040T pci device id

2008-06-18T03:07:03+00:00

Missed one pci id for 88E8040T.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik

sky2: Hold RTNL while calling dev_close()

2008-06-10T22:40:44+00:00

dev_close() must be called holding the RTNL.

Signed-off-by: Ben Hutchings 
Signed-off-by: Jeff Garzik

sky2: restore vlan acceleration on reset

2008-05-22T09:59:36+00:00

If device has to be reset by sky2_restart, then need to restore
the VLAN acceleration settings.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik

sky2: missing chip name for Yukon Supreme

2008-04-12T05:52:35+00:00

Any usage of sky2 on new Yukon Supreme would cause a NULL dereference.
The chip is very new, so the support is still untested; vendor has
not sent any eval hardware.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik

sky2: fix suspend/resume races

2008-04-02T16:33:53+00:00

There are a couple of possible races on suspend/resume.
First the driver needs to block new packets from being queued for Tx.
The other less likely problem is the watchdog timer going off
during resume.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

sky2: fix LED management

2008-02-24T05:07:39+00:00

Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik

sky2: fix for Yukon FE (regression in 2.6.25)

2008-02-05T18:31:09+00:00

The Yukon FE chip has a ram buffer therefore it needs the alignment
restriction and hang check workarounds.

Therefore:
  * Autodetect the prescence/absence of ram buffer
  * Rename the flag value to reflect this
  * Use it consistently (ie don't reread register)

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik

sky2: fix Wake On Lan interaction with BIOS

2008-02-03T12:28:44+00:00

This patch disables config mode access after clearing PCI settings.
Some BIOS's seem to not do WOL if config bit still set.

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=9721

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik 
Signed-off-by: David S. Miller

sky2: restore multicast addresses after recovery

2008-02-03T12:28:44+00:00

If the sky2 deadman timer forces a recovery, the multicast hash
list is lost. Move the call to sky2_set_multicast to the end
of sky2_up() so all paths that bring device up will restore multicast.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik 
Signed-off-by: David S. Miller

sky2: version 1.21

2008-01-28T23:08:02+00:00

Update driver version reflects new hardware support.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Jeff Garzik