linux-stable.git/drivers/net/phy, branch v5.2.8

net: phy: fix race in genphy_update_link

2019-08-09T15:51:47+00:00

[ Upstream commit aa6b1956158f1afc52761137620d4b3f8a058d24 ]

In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".

[0] https://marc.info/?t=156413509900003&r=1&w=2

Fixes: 4950c2ba49cc ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong 
Tested-by: liuyonglong 
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: mscc: initialize stats array

2019-08-09T15:51:44+00:00

[ Upstream commit f972037e71246c5e0916eef835174d58ffc517e4 ]

The memory allocated for the stats array may contain arbitrary data.

Fixes: e4f9ba642f0b ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e0e78 ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc5218 ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phylink: Fix flow control for fixed-link

2019-08-09T15:51:44+00:00

[ Upstream commit 8aace4f3eba2a3ceb431e18683ea0e1ecbade5cd ]

In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.

By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.

Results with this patch.

Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
  validate().
- flow = results reported my link is Up line.

+-----+------------+-------+
| DT  | validate() | flow  |
+-----+------------+-------+
| Yes | Yes        | rx/tx |
| No  | Yes        | off   |
| Yes | No         | off   |
+-----+------------+-------+

Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst 
Acked-by: Russell King 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phylink: don't start and stop SGMII PHYs in SFP modules twice

2019-08-09T15:51:44+00:00

[ Upstream commit c7fa7f567cab6532be285a5df104617d80bce245 ]

SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.

Since commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:

  % ip link set up dev eth0
  ------------[ cut here ]------------
  called from state UP
  WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
  Modules linked in:
  CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
  NIP:  c0227bf0 LR: c0227bf0 CTR: c004d224
  REGS: df547720 TRAP: 0700   Not tainted  (5.2.0+)
  MSR:  00029000   CR: 24002822  XER: 00000000

  GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
  GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
  GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
  GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
  NIP [c0227bf0] phy_start+0x74/0xc0
  LR [c0227bf0] phy_start+0x74/0xc0
  Call Trace:
  [df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
  [df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
  [df547828] [c023cf08] gfar_enet_open+0x364/0x374
  [df547898] [c029d870] __dev_open+0xe4/0x140
  [df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
  [df5478f8] [c029dc28] dev_change_flags+0x20/0x54
  [df547918] [c02ae304] do_setlink+0x310/0x818
  [df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df547c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
  --- interrupt: c01 at 0xfd4e030
      LR = 0xfd4e010
  Instruction dump:
  813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
  3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
  ---[ end trace d4c095aeaf6ea998 ]---

and

  % ip link set down dev eth0
  ------------[ cut here ]------------
  called from state HALTED
  WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88

  <...>

  Call Trace:
  [df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
  [df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
  [df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
  [df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
  [df581858] [c0225608] phylink_stop+0x7c/0xe4
  [df581868] [c023c57c] stop_gfar+0x7c/0x94
  [df581888] [c023c5b8] gfar_close+0x24/0x94
  [df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
  [df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
  [df5818f8] [c029dc28] dev_change_flags+0x20/0x54
  [df581918] [c02ae304] do_setlink+0x310/0x818
  [df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df581c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df581f38] [c000d1d8] ret_from_syscall+0x0/0x38

  <...>

  ---[ end trace d4c095aeaf6ea999 ]---

SFP modules with the 1000Base-X interface are not affected.

Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.

Fixes: 217962615662 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha 
Acked-by: Russell King 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: fixed_phy: print gpio error only if gpio node is present

2019-08-09T15:51:44+00:00

[ Upstream commit ab98c008ac761752cdc27f9eb053419feadeb2f7 ]

It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.

Fixes: 5468e82f7034 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: sfp: hwmon: Fix scaling of RX power

2019-07-28T06:27:14+00:00

[ Upstream commit 0cea0e1148fe134a4a3aaf0b1496f09241fb943a ]

The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.

With this change in place, sensors(1) and ethtool -m agree:

sff2-isa-0000
Adapter: ISA adapter
in0:          +3.23 V
temp1:        +33.1 C
power1:      270.00 uW
power2:      200.00 uW
curr1:        +0.01 A

        Laser output power                        : 0.2743 mW / -5.62 dBm
        Receiver signal average optical power     : 0.2014 mW / -6.96 dBm

Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn 
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: sfp: add mutex to prevent concurrent state checks

2019-07-26T07:10:23+00:00

[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]

sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.

Suggested-by: Russell King 
Signed-off-by: Robert Hancock 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: Check against net_device being NULL

2019-07-26T07:10:19+00:00

[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei 
Suggested-by: Andrew Lunn 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

Revert "net: phylink: set the autoneg state in phylink_phy_change"

2019-06-16T01:10:30+00:00

This reverts commit ef7bfa84725d891bbdb88707ed55b2cbf94942bb.

Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.

Signed-off-by: David S. Miller

net: phylink: set the autoneg state in phylink_phy_change

2019-06-15T20:29:32+00:00

The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.

Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei 
Signed-off-by: David S. Miller