linux-stable.git/drivers/net/phy, branch v4.4.185

mdio_bus: Fix use-after-free on device_register fails

2019-03-23T07:44:30+00:00

[ Upstream commit 6ff7b060535e87c2ae14dd8548512abfdda528fb ]

KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.

KASAN report details as below:

BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524

CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xfa/0x1ce lib/dump_stack.c:113
 print_address_description+0x65/0x270 mm/kasan/report.c:187
 kasan_report+0x149/0x18d mm/kasan/report.c:317
 mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
 fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
 ? 0xffffffffc0e40000
 ? 0xffffffffc0e40000
 ? 0xffffffffc0e40000
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004

Allocated by task 3524:
 set_track mm/kasan/common.c:85 [inline]
 __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
 kmalloc include/linux/slab.h:545 [inline]
 kzalloc include/linux/slab.h:740 [inline]
 mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
 fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 3524:
 set_track mm/kasan/common.c:85 [inline]
 __kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
 slab_free_hook mm/slub.c:1409 [inline]
 slab_free_freelist_hook mm/slub.c:1436 [inline]
 slab_free mm/slub.c:2986 [inline]
 kfree+0xe1/0x270 mm/slub.c:3938
 device_release+0x78/0x200 drivers/base/core.c:919
 kobject_cleanup lib/kobject.c:662 [inline]
 kobject_release lib/kobject.c:691 [inline]
 kref_put include/linux/kref.h:67 [inline]
 kobject_put+0x146/0x240 lib/kobject.c:708
 put_device+0x1c/0x30 drivers/base/core.c:2060
 __mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
 fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8881dc824c80
 which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
 2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                                ^
 ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: Micrel KSZ8061: link failure after cable connect

2019-03-23T07:44:23+00:00

[ Upstream commit 232ba3a51cc224b339c7114888ed7f0d4d95695e ]

With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.

DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).

END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.

WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
   register 2, prior to connecting the cable or prior to setting the
   Restart Auto-negotiation bit in register 0h. The MMD registers are
   accessed via the indirect access registers Dh and Eh, or via the Micrel
   EthUtil utility as shown here:
   . if using the EthUtil utility (usually with a Micrel KSZ8061
     Evaluation Board), type the following commands:
     > address 1
     > mmd 1
     > iw 2 b61a
   . Alternatively, write the following registers to write to the
     indirect MMD register:
     Write register Dh, data 0001h
     Write register Eh, data 0002h
     Write register Dh, data 4001h
     Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
   either by the strapping option, or by clearing bit 12 in register 0h.
   Care must be taken to ensure that the KSZ8061 and the link partner
   will link with the same speed and duplex. Note that the KSZ8061
   defaults to full-duplex when auto-negotiation is off, but other
   devices may default to half-duplex in the event of failed
   auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
   or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
   be recovered by setting the Restart Auto-Negotiation bit in
   register 0h, or by resetting or power cycling the device. Reset may
   be either hardware reset or software reset (register 0h, bit 15).

PLAN
This errata will not be corrected in the future revision.

Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch 
Signed-off-by: Rajasingh Thavamani 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: dp83640: expire old TX-skb

2019-02-20T09:13:15+00:00

[ Upstream commit 53bc8d2af08654659abfadfd3e98eb9922ff787c ]

During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.

Purge old skbs in decode_txts().

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior 
Reviewed-by: Kurt Kanzenbach 
Acked-by: Richard Cochran 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: don't allow __set_phy_supported to add unsupported modes

2018-12-17T20:55:08+00:00

[ Upstream commit d2a36971ef595069b7a600d1144c2e0881a930a1 ]

Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.

The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.

Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: fix flag masking in __set_phy_supported

2018-07-25T08:18:17+00:00

[ Upstream commit df8ed346d4a806a6eef2db5924285e839604b3f9 ]

Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.

Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: broadcom: Fix bcm_write_exp()

2018-06-13T14:15:29+00:00

[ Upstream commit 79fb218d97980d4fee9a64f4c8ff05289364ba25 ]

On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.

Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.

broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).

Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

dp83640: Ensure against premature access to PHY registers after reset

2018-05-30T05:49:08+00:00

[ Upstream commit 76327a35caabd1a932e83d6a42b967aa08584e5d ]

The datasheet specifies a 3uS pause after performing a software
reset. The default implementation of genphy_soft_reset() does not
provide this, so implement soft_reset with the needed pause.

Signed-off-by: Esben Haabendal 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

net: phy: avoid genphy_aneg_done() for PHYs without clause 22 support

2018-04-13T17:50:18+00:00

[ Upstream commit 41408ad519f7a2a1c5229e61f2a97f4df1b61adc ]

Avoid calling genphy_aneg_done() for PHYs that do not implement the
Clause 22 register set.

Clause 45 PHYs may implement the Clause 22 register set along with the
Clause 22 extension MMD.  Hence, we can't simply block access to the
Clause 22 functions based on the PHY being a Clause 45 PHY.

Signed-off-by: Russell King 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mdio-sun4i: Fix a memory leak

2018-03-03T09:19:45+00:00

[ Upstream commit 56c0290202ab94a2f2780c449395d4ae8495fab4 ]

If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.

Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround

2018-01-02T19:33:26+00:00

[ Upstream commit c1a8d0a3accf64a014d605e6806ce05d1c17adf1 ]

Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.

Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().

Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman