linux-stable.git/drivers/net/phy, branch v4.19.63 Linux kernel stable tree net: phy: sfp: hwmon: Fix scaling of RX power 2019-07-28T06:29:24+00:00 Andrew Lunn andrew@lunn.ch 2019-07-21T16:50:08+00:00 201d7d62a82a01f6085adc08e9fa2c093f717d25 [ Upstream commit 0cea0e1148fe134a4a3aaf0b1496f09241fb943a ] The RX power read from the SFP uses units of 0.1uW. This must be scaled to units of uW for HWMON. This requires a divide by 10, not the current 100. With this change in place, sensors(1) and ethtool -m agree: sff2-isa-0000 Adapter: ISA adapter in0: +3.23 V temp1: +33.1 C power1: 270.00 uW power2: 200.00 uW curr1: +0.01 A Laser output power : 0.2743 mW / -5.62 dBm Receiver signal average optical power : 0.2014 mW / -6.96 dBm Reported-by: chris.healy@zii.aero Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 0cea0e1148fe134a4a3aaf0b1496f09241fb943a ]

The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.

With this change in place, sensors(1) and ethtool -m agree:

sff2-isa-0000
Adapter: ISA adapter
in0:          +3.23 V
temp1:        +33.1 C
power1:      270.00 uW
power2:      200.00 uW
curr1:        +0.01 A

        Laser output power                        : 0.2743 mW / -5.62 dBm
        Receiver signal average optical power     : 0.2014 mW / -6.96 dBm

Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: sfp: add mutex to prevent concurrent state checks 2019-07-26T07:14:05+00:00 Robert Hancock hancock@sedsystems.ca 2019-06-07T16:42:36+00:00 c7bf2df4504439480afce68e84490d5d976deebc [ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ] sfp_check_state can potentially be called by both a threaded IRQ handler and delayed work. If it is concurrently called, it could result in incorrect state management. Add a st_mutex to protect the state - this lock gets taken outside of code that checks and handle state changes, and the existing sm_mutex nests inside of it. Suggested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]

sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.

Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: phy: Check against net_device being NULL 2019-07-26T07:14:02+00:00 Ioana Ciornei ioana.ciornei@nxp.com 2019-05-28T17:38:09+00:00 fc25cfb03ea2918ab529dfef9fc45b4025943e3b [ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ] In general, we don't want MAC drivers calling phy_attach_direct with the net_device being NULL. Add checks against this in all the functions calling it: phy_attach() and phy_connect_direct(). Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: phy: rename Asix Electronics PHY driver 2019-07-14T06:11:08+00:00 Michael Schmitz schmitzmic@gmail.com 2019-06-07T05:37:34+00:00 374180b11b299779893ad14553bb49e0e0242bdc [ Upstream commit a9520543b123bbd7275a0ab8d0375a5412683b41 ] [Resent to net instead of net-next - may clash with Anders Roxell's patch series addressing duplicate module names] Commit 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver") introduced a new PHY driver drivers/net/phy/asix.c that causes a module name conflict with a pre-existiting driver (drivers/net/usb/asix.c). The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded by that driver via its PHY ID. A rename of the driver looks unproblematic. Rename PHY driver to ax88796b.c in order to resolve name conflict. Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Fixes: 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a9520543b123bbd7275a0ab8d0375a5412683b41 ]

[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]

Commit 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).

The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.

Rename PHY driver to ax88796b.c in order to resolve name conflict.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: phy: dp83867: Set up RGMII TX delay 2019-06-22T06:15:20+00:00 Max Uvarov muvarov@gmail.com 2019-05-28T10:00:52+00:00 7b9e10944f0dc82627321288a3012c2cf233f85d [ Upstream commit 2b892649254fec01678c64f16427622b41fa27f4 ] PHY_INTERFACE_MODE_RGMII_RXID is less then TXID so code to set tx delay is never called. Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy") Signed-off-by: Max Uvarov <muvarov@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2b892649254fec01678c64f16427622b41fa27f4 ]

PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.

Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: phylink: ensure consistent phy interface mode 2019-06-22T06:15:20+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-05-28T09:27:21+00:00 7698ad8c14c7ba8fc4364e6c9150c94203de7333 [ Upstream commit c678726305b9425454be7c8a7624290b602602fc ] Ensure that we supply the same phy interface mode to mac_link_down() as we did for the corresponding mac_link_up() call. This ensures that MAC drivers that use the phy interface mode in these methods can depend on mac_link_down() always corresponding to a mac_link_up() call for the same interface mode. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c678726305b9425454be7c8a7624290b602602fc ]

Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call.  This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: sfp: read eeprom in maximum 16 byte increments 2019-06-11T10:20:49+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-06-02T14:13:00+00:00 9740f4ff1a66ff3d7f3e69da9f84421522c0e99f [ Upstream commit 28e74a7cfd6403f0d1c0f8b10b45d6fae37b227e ] Some SFP modules do not like reads longer than 16 bytes, so read the EEPROM in chunks of 16 bytes at a time. This behaviour is not specified in the SFP MSAs, which specifies: "The serial interface uses the 2-wire serial CMOS E2PROM protocol defined for the ATMEL AT24C01A/02/04 family of components." and "As long as the SFP+ receives an acknowledge, it shall serially clock out sequential data words. The sequence is terminated when the host responds with a NACK and a STOP instead of an acknowledge." We must avoid breaking a read across a 16-bit quantity in the diagnostic page, thankfully all 16-bit quantities in that page are naturally aligned. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 28e74a7cfd6403f0d1c0f8b10b45d6fae37b227e ]

Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time.  This behaviour is not specified
in the SFP MSAs, which specifies:

 "The serial interface uses the 2-wire serial CMOS E2PROM protocol
  defined for the ATMEL AT24C01A/02/04 family of components."

and

 "As long as the SFP+ receives an acknowledge, it shall serially clock
  out sequential data words. The sequence is terminated when the host
  responds with a NACK and a STOP instead of an acknowledge."

We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: phy: marvell10g: report if the PHY fails to boot firmware 2019-06-04T06:02:32+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-05-28T09:34:42+00:00 33f737a4307dcc85ca850b1fc8e29899922ffed7 [ Upstream commit 3d3ced2ec5d71b99d72ae6910fbdf890bc2eccf0 ] Some boards do not have the PHY firmware programmed in the 3310's flash, which leads to the PHY not working as expected. Warn the user when the PHY fails to boot the firmware and refuse to initialise. Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 3d3ced2ec5d71b99d72ae6910fbdf890bc2eccf0 ]

Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected.  Warn the user when the
PHY fails to boot the firmware and refuse to initialise.

Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi: Micrel eth switch: declare missing of table 2019-05-16T17:41:25+00:00 Daniel Gomez dagmcr@gmail.com 2019-04-22T19:08:03+00:00 09185e35982784678ad1a9e72a1ad0c0abe07f4d [ Upstream commit 2f23a2a768bee7ad2ff1e9527c3f7e279e794a46 ] Add missing <of_device_id> table for SPI driver relying on SPI device match since compatible is in a DT binding or in a DTS. Before this patch: modinfo drivers/net/phy/spi_ks8995.ko | grep alias alias: spi:ksz8795 alias: spi:ksz8864 alias: spi:ks8995 After this patch: modinfo drivers/net/phy/spi_ks8995.ko | grep alias alias: spi:ksz8795 alias: spi:ksz8864 alias: spi:ks8995 alias: of:N*T*Cmicrel,ksz8795C* alias: of:N*T*Cmicrel,ksz8795 alias: of:N*T*Cmicrel,ksz8864C* alias: of:N*T*Cmicrel,ksz8864 alias: of:N*T*Cmicrel,ks8995C* alias: of:N*T*Cmicrel,ks8995 Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2f23a2a768bee7ad2ff1e9527c3f7e279e794a46 ]

Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.

Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias:          spi:ksz8795
alias:          spi:ksz8864
alias:          spi:ks8995

After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias:          spi:ksz8795
alias:          spi:ksz8864
alias:          spi:ks8995
alias:          of:N*T*Cmicrel,ksz8795C*
alias:          of:N*T*Cmicrel,ksz8795
alias:          of:N*T*Cmicrel,ksz8864C*
alias:          of:N*T*Cmicrel,ksz8864
alias:          of:N*T*Cmicrel,ks8995C*
alias:          of:N*T*Cmicrel,ks8995

Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
net: phy: marvell: Fix buffer overrun with stats counters 2019-05-05T12:42:38+00:00 Andrew Lunn andrew@lunn.ch 2019-04-24T22:33:00+00:00 1d412d873a12f5d7aa1d8ef1792f330a5e0a27c2 [ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ] marvell_get_sset_count() returns how many statistics counters there are. If the PHY supports fibre, there are 3, otherwise two. marvell_get_strings() does not make this distinction, and always returns 3 strings. This then often results in writing past the end of the buffer for the strings. Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ]

marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.

marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.

Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>