linux-stable.git/drivers/net/phy, branch v4.19.192

net: phy: marvell: fix detection of PHY on Topaz switches

2021-04-28T11:16:51+00:00

commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.

Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.

This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.

This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.

Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.

Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.

Prior this change Topaz's internal PHY is detected by kernel as:

  PHY [...] driver [Marvell 88E6390] (irq=63)

And afterwards as:

  PHY [...] driver [Marvell 88E6341 Family] (irq=63)

Signed-off-by: Pali Rohár 
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: broadcom: Only advertise EEE for supported modes

2021-04-16T09:49:30+00:00

commit c056d480b40a68f2520ccc156c7fae672d69d57d upstream

We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.

Fixes: 99cec8a4dda2 ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Florian Fainelli 
Signed-off-by: Sasha Levin

net: phy: fix save wrong speed and duplex problem if autoneg is on

2021-03-17T15:43:45+00:00

[ Upstream commit d9032dba5a2b2bbf0fdce67c8795300ec9923b43 ]

If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.

And duplex setting has same problem too.

However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.

Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang 
Signed-off-by: Huazhong Tan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

sfp: Fix error handing in sfp_probe()

2020-11-10T11:35:54+00:00

[ Upstream commit 9621618130bf7e83635367c13b9a6ee53935bb37 ]

gpiod_to_irq() never return 0, but returns negative in
case of error, check it and set gpio_irq to 0.

Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: YueHaibing 
Reviewed-by: Andrew Lunn 
Link: https://lore.kernel.org/r/20201031031053.25264-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Greg Kroah-Hartman

mdio: fix mdio-thunder.c dependency & build error

2020-10-14T08:31:25+00:00

[ Upstream commit 7dbbcf496f2a4b6d82cfc7810a0746e160b79762 ]

Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:

ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'

Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot 
Signed-off-by: Randy Dunlap 
Cc: Bartosz Golaszewski 
Cc: Andrew Lunn 
Cc: Heiner Kallweit 
Cc: netdev@vger.kernel.org
Cc: David Daney 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: Avoid NPD upon phy_detach() when driver is unbound

2020-09-26T16:01:30+00:00

[ Upstream commit c2b727df7caa33876e7066bde090f40001b6d643 ]

If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:

echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down

Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: dp83640: fix SIOCSHWTSTAMP to update the struct with actual configuration

2020-07-29T08:16:49+00:00

[ Upstream commit 473309fb8372365ad211f425bca760af800e10a7 ]

From Documentation/networking/timestamping.txt:

  A driver which supports hardware time stamping shall update the
  struct with the actual, possibly more permissive configuration.

Do update the struct passed when we upscale the requested time
stamping mode.

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov 
Acked-by: Richard Cochran 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: sfp: add some quirks for GPON modules

2020-07-22T07:32:03+00:00

[ Upstream commit b0eae33b2583dceb36224619f9fd85e6140ae594 ]

Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM.  It seems rather common that GPON modules
mis-report.

Let's fix these modules by adding some quirks.

Signed-off-by: Russell King 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: sfp: add support for module quirks

2020-07-22T07:32:03+00:00

[ Upstream commit b34bb2cb5b62c7397c28fcc335e8047a687eada4 ]

Add support for applying module quirks to the list of supported
ethtool link modes.

Signed-off-by: Russell King 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: Check harder for errors in get_phy_id()

2020-07-01T03:17:06+00:00

[ Upstream commit b2ffc75e2e990b09903f9d15ccd53bc5f3a4217c ]

Commit 02a6efcab675 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.

In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).

The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.

Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.

Fixes: 02a6efcab675 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn 
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman