linux-stable.git/drivers/net/phy, branch v4.19.136

net: dp83640: fix SIOCSHWTSTAMP to update the struct with actual configuration

2020-07-29T08:16:49+00:00

[ Upstream commit 473309fb8372365ad211f425bca760af800e10a7 ]

From Documentation/networking/timestamping.txt:

  A driver which supports hardware time stamping shall update the
  struct with the actual, possibly more permissive configuration.

Do update the struct passed when we upscale the requested time
stamping mode.

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov 
Acked-by: Richard Cochran 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: sfp: add some quirks for GPON modules

2020-07-22T07:32:03+00:00

[ Upstream commit b0eae33b2583dceb36224619f9fd85e6140ae594 ]

Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM.  It seems rather common that GPON modules
mis-report.

Let's fix these modules by adding some quirks.

Signed-off-by: Russell King 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: sfp: add support for module quirks

2020-07-22T07:32:03+00:00

[ Upstream commit b34bb2cb5b62c7397c28fcc335e8047a687eada4 ]

Add support for applying module quirks to the list of supported
ethtool link modes.

Signed-off-by: Russell King 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: Check harder for errors in get_phy_id()

2020-07-01T03:17:06+00:00

[ Upstream commit b2ffc75e2e990b09903f9d15ccd53bc5f3a4217c ]

Commit 02a6efcab675 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.

In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).

The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.

Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.

Fixes: 02a6efcab675 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn 
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: fix aneg restart in phy_ethtool_set_eee

2020-05-20T06:18:35+00:00

[ Upstream commit 9de5d235b60a7cdfcdd5461e70c5663e713fde87 ]

phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.

Fixes: f75abeb8338e ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

dp83640: reverse arguments to list_add_tail

2020-05-14T05:57:17+00:00

[ Upstream commit 865308373ed49c9fb05720d14cbf1315349b32a9 ]

In this code, it appears that phyter_clocks is a list head, based on
the previous list_for_each, and that clock->list is intended to be a
list element, given that it has just been initialized in
dp83640_clock_init.  Accordingly, switch the arguments to
list_add_tail, which takes the list head as the second argument.

Fixes: cb646e2b02b27 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Julia Lawall 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before accessing PHY registers

2020-04-13T08:45:08+00:00

[ Upstream commit 6110dff776f7fa65c35850ef65b41d3b39e2fac2 ]

After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.

If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.

This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.

The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.

This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().

Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: mdio-mux-bcm-iproc: check clk_prepare_enable() return value

2020-04-02T13:28:13+00:00

[ Upstream commit 872307abbd0d9afd72171929806c2fa33dc34179 ]

Check clk_prepare_enable() return value.

Fixes: 2c7230446bc9 ("net: phy: Add pm support to Broadcom iProc mdio mux driver")
Signed-off-by: Rayagonda Kokatanur 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: fix MDIO bus PM PHY resuming

2020-03-18T06:14:17+00:00

[ Upstream commit 611d779af7cad2b87487ff58e4931a90c20b113c ]

So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.

To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.

Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven 
Tested-by: Geert Uytterhoeven 
Signed-off-by: Heiner Kallweit 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: Avoid multiple suspends

2020-03-18T06:14:10+00:00

commit 503ba7c6961034ff0047707685644cad9287c226 upstream.

It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().

Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.

This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.

Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman