linux-stable.git/drivers/net/phy/phy_device.c, branch v5.2.7

net: phy: Check against net_device being NULL

2019-07-26T07:10:19+00:00

[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei 
Suggested-by: Andrew Lunn 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2019-05-08T00:22:09+00:00

Minor conflict with the DSA legacy code removal.

Signed-off-by: David S. Miller

net: phy: fix phy_validate_pause

2019-05-05T08:04:10+00:00

We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.

See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes

The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.

Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: phy: improve pause handling

2019-05-04T04:47:55+00:00

When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.

In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.

Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: phy: avoid unneeded MDIO reads in genphy_read_status

2019-04-28T23:48:04+00:00

Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: phy: improve genphy_soft_reset

2019-04-26T15:56:54+00:00

PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.

So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.

BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: phy: don't set autoneg if it's not supported

2019-04-18T23:10:27+00:00

In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: phy: fix setting autoneg_complete in genphy_update_link

2019-04-08T23:35:52+00:00

The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.

Fixes: 4950c2ba49cc ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman 
Tested-by: Simon Horman 
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: phy: replace genphy_10g_driver with genphy_c45_driver

2019-04-08T23:24:05+00:00

Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.

Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: phy: improve link partner capability detection

2019-04-08T22:18:00+00:00

genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().

It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.

Signed-off-by: Heiner Kallweit 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller